Lee Maker And Storage Bin; Refrigerator Features; Refrigerator Shelvee - Kenmore Side by Side Refrigerator Use & Care Manual

2, Remove the cap by turning it ceur~terclockwise antit it stops,
IMPORTANT: Do not discar(I the cap, It is part of your
refrigerator, Keep the c,~p to Lies with the replacement lil~er.
3. With tile cap in a borlzontal position, in~rt the cap into the
base grille until It stops,
,..~1~:-
4. Turn tile cap counterclockwise until the cap slips into tire
................................................ attachment,slot:, ~t'.hen;.tern the cep.eloekwiee,ur~til.it.ls irt a ....................
horizontal position.
NOTE= The cap will not be even with the b,~tse grille,
Turning the ice Maker On/Off
[o turn ON the ice maker, simply lower the wire shutoff arrn,
To mant.lai]y turn off the ice rnaker, llft the wire shutoff arm to the
OFF (arm up) position and listen for the click,
NOTEz Your ice maker has an autornatic shutoff, As ice is reade,
the ice cubes will fill the ice storage bin, and the ice cubes will
raise the wire shutoff arm [o the OFF (arm up) position, Do not
force the wire shutoff arm up or down.
R~MEMB~R=
Allow 24 hours to produce ~he first batch o~ ice, Discard the
first three batches of ice produced,
The quality of your ice will be only as good as the quality of
the water supplied to your ice maker, Avoid connecting the
ice maker to a softened water supply, Water softener
chemicals (such as sail) can damage pa~s of the ice maker
and lead to peer quality ice. I[ a softened water supply c~tnnot
be avoided, make sere the water soflener is operating
propedy and is well maln[alned,
¯ Do not use anything sharp to break up the ice in the storage
bin, This can cause damage to the ice container and the
dispenser mechanism,
¯ Do not store anything on top of or in the ice maker or storage
bird,
Removing and Replacing Ice Storage Bin
Pull the covering panel up frorr'~ the bottom and then slide it
back toward the rear,
Lift the wire shutoff arm so it clicks into the OFF Cap) position,
Ice can still be dispensed, but no more can be made,
Lift ~.~p the front of the storage bin and pull it out,
4, Replace the bin by pushing it in all the way or the dispenser
will act work, Push the wire shutoff arm clown to the ON
position to rest~:~rt ice production, Make sere the door is
closed tightly,
REFRIGERATOR FEATURES
Your itrodel may have some or all of these features, Features that
can be purchased separately as product accessories are labeled
with the word "Accessory," Not all accessories will fit all models,
If you are interested in purchasing one of the accessories, please
call fbe toll.,free number on ~he bask {;over or in the
"Accessories" section,
Important Informatio~ to know about glass shelves
asd covers:
1'.)o not clean glass shelves or covers with warm water when
they are cold, Shelves and covers may break if exposed to
..... sr.ldden, tempetature.changes.'or'impact;..such' as.bumping; ........................................................
Per your protection, tempered glass is designed to abetter
i~to many small, pebble-size pieces, This is normal. Glass
shelves and covers are heavy, Use special care wllen
together and adjnst the shelves to fit dllfereat heights, This
reduces tbe time the refdgerator door Is open and saves energy. ~>~
Slide=Out Shelves (on some models) ~
To Remove and Replace a Shelf in a Metal Frame;
1. Pull the shelf forward to the stop, Tilt the front of the shelf up
and lift it slightly as yea pull the shelf from the frame,
2. Replace the shelf by guiding tt back into the slots on the
frame and pushing the shelf In past the stop,
Shelves and Shelf Frames
To Remove and Replace a Shelf/Frame;
1. Remove the shelf/frame by tilting it up at the front and lifting it
out of the shelf supports.
2. Replace the shelf/frame by guiding the rear shelf hooks into
the shelf s*Jpports, Tilt the front of the shelf up ur~til rear shelf
hooks drop into tbe shelf supports, Check to make sure that
the shelf is securely in position,
13