Hilti TE 1000-AVR Operating Instructions Manual
Hide thumbs
Also See for TE 1000-AVR:
- User manual ,
- Operating instructions manual (235 pages) ,
- Original operating instructions (188 pages)
Related Manuals for Hilti TE 1000-AVR
Summary of Contents for Hilti TE 1000-AVR
- Page 1 TE 1000-AVR / TE 1500-AVR Operating instructions Mode d’emploi Manual de instrucciones Manual de instruções...
- Page 2 This Product is Certified Ce produit est certifié Este producto esta certificado Este produto está certificado...
-
Page 5: Table Of Contents
In these operating instructions, the designation “the Always keep these operating instructions power tool” always refers to the TE 1000-AVR and / together with the power tool. or TE 1500-AVR breaker. Ensure that the operating instructions are... -
Page 6: Description
Make a note of this data in your operating instructions and always refer to it when making an Wear eye Wear a hard Wear ear Wear enquiry to your Hilti representative or service depart- protection protection protective ment. gloves Type: Serial no.:... - Page 7 The power tool may be operated only when connected to a power supply providing a voltage and frequency in compliance with the information given on its type identification plate. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance.
-
Page 8: Accessories, Consumables
Dust removal module TE DRS B Use the Hilti chisels or other tools listed below. With these chisels and tools you will achieve higher performance and longer lifetime as the power tool and chisels have been optimized as a system. -
Page 9: Technical Data
Width in Length in TE-S chuck Designation Width (mm) Length (mm) inches inches Flat chisels TE SP FM 36 TE SP FM 50 TE SP FM 70 Wide-flat chisels TE SP SPM 5/36 Wide-flat chisels TE SP SPM 5/50 Wide-flat chisels TE SP SPM 8/36 Wide-flat chisels... -
Page 10: Safety Instructions
Power tool TE 1000 AVR TE 1500 AVR 32.5 Hz 27 Hz Hammering frequency under load Information about the power tool and its applications Protection class Protection class I 5. Safety instructions cord suitable for outdoor use reduces the risk of 5.1 General power tool safety warnings electric shock. - Page 11 5.1.4 Power tool use and care 5.2 Additional safety instructions a) Do not force the power tool. Use the correct 5.2.1 Personal protective equipment power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
- Page 12 Hilti Customer Service. Check extension cords j) The appliance is not intended for use by chil- at regular intervals and replace them if found dren, by debilitated persons or those who have to be damaged.
-
Page 13: Before Use
area. Untidiness at the workplace can lead to 5.2.4 Work area accidents. c) If the work involves breaking right through, take the appropriate safety measures at the opposite side. Parts breaking away could fall out and / or fall down and injure other persons. a) Ensure that the workplace is well ventilated. - Page 14 If the power tool starts without pressing the on/off operating instructions for the theft protection system. switch when the supply cord is plugged back in after 7.2.2 Chiseling unplugging, the power tool must be brought to Hilti Service immediately. 7.2.2.1 Working at low temperatures NOTE...
-
Page 15: Care And Maintenance
NOTE 7.3 Chiseling tips As starting is electronically controlled, the power 7.3.1 Starting chiseling 7 tool’s starting characteristics may be different in cold Position the tip of the chisel approx. 80-100 mm from conditions. the edge of the workpiece. 7.2.2.2 Switching on 7.3.2 Reinforcing bars 8 1. -
Page 16: Troubleshooting
Check all external parts of the power tool for dam- with Hilti grease. It is essential that the dust shield age at regular intervals and check that all controls is replaced if the sealing lip is found to be damaged. -
Page 17: Disposal
NOTE If the fault cannot be eliminated by the measures listed above, have the power tool checked by Hilti Service. 10. Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. -
Page 18: Manufacturer's Warranty - Tools
11. Manufacturer’s warranty - tools Hilti warrants that the tool supplied is free of defects Additional claims are excluded, unless stringent na- in material and workmanship. This warranty is valid tional rules prohibit such exclusion. In particular, so long as the tool is operated and handled correctly,... - Page 19 Fax: +423 / 234 29 65 www.hilti.com 248973 / A Hilti = registered trademark of Hilti Corp., Schaan W 3150 0609 00-Pos. 3 1 Printed in Liechtenstein © 2009 Right of technical and programme changes reserved S. E. & O.
Need help?
Do you have a question about the TE 1000-AVR and is the answer not in the manual?
Questions and answers