Hilti TE 1000-AVR Original Operating Instructions
Hide thumbs
Also See for TE 1000-AVR:
- User manual ,
- Operating instructions manual (235 pages) ,
- Original operating instructions (188 pages)
Table of Contents
Advertisement
Quick Links
Printed: 16.05.2014 | Doc-Nr: PUB / 5070757 / 000 / 03
TE 1000-AVR /
TE 1500-AVR
Bedienungsanleitung
Operating instructions
Οδηγιες χρησεως
Használati utasítás
Instrukcja obsługi
Инструкция по зксплуатации
Návod k obsluze
Návod na obsluhu
Upute za uporabu
Navodila za uporabo
Ръководство за обслужване
Instrucţiuni de utilizare
Kulllanma Talimatı
IНСТРУКЦIЯ З ЕКСПЛУАТАЦIЇ
Пайдалану бойынша басшылық
de
en
el
hu
pl
ru
cs
sk
hr
sl
bg
ro
tr
ar
uk
kk
ja
ko
zh
cn
Advertisement
Table of Contents
Related Manuals for Hilti TE 1000-AVR
Summary of Contents for Hilti TE 1000-AVR
- Page 1 TE 1000-AVR / TE 1500-AVR Bedienungsanleitung Operating instructions Οδηγιες χρησεως Használati utasítás Instrukcja obsługi Инструкция по зксплуатации Návod k obsluze Návod na obsluhu Upute za uporabu Navodila za uporabo Ръководство за обслужване Instrucţiuni de utilizare Kulllanma Talimatı IНСТРУКЦIЯ З ЕКСПЛУАТАЦIЇ...
- Page 2 Printed: 16.05.2014 | Doc-Nr: PUB / 5070757 / 000 / 03...
- Page 3 Printed: 16.05.2014 | Doc-Nr: PUB / 5070757 / 000 / 03...
- Page 4 Printed: 16.05.2014 | Doc-Nr: PUB / 5070757 / 000 / 03...
-
Page 5: Table Of Contents
In these operating instructions, the designation “the Always keep these operating instructions to- power tool” always refers to the TE 1000-AVR and / gether with the power tool. or TE 1500-AVR breaker. Ensure that the operating instructions are... -
Page 6: Description
Make a note of this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative or service department. Wear eye Wear a hard... - Page 7 To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance. Modification of the power tool or tampering with its parts is not permissible.
-
Page 8: Accessories, Consumables
Dust removal module TE DRS‑B Use the Hilti chisels or other tools listed below. With these chisels and tools you will achieve higher performance and longer lifetime as the power tool and chisels have been optimized as a system. TE‑S chuck /... -
Page 9: Technical Data
TE‑S chuck / Width in Length in tool designa- Width (mm) Length (mm) inches inches tion Flexible chisel TE‑S‑BSPM 25¹⁄₂ Scraper / flexible chisel TE‑SP‑SPMK 4³⁄₄ 12/50 Pointed flat chisel TE‑S‑SPI 50 4¹⁄₂ 19¹⁄₈ Ballast bed chisel TE‑S‑TT 60 Shank TE‑S‑SS 11³⁄₄... -
Page 10: Safety Instructions
Noise and vibration information (measured in accordance with EN 60745‑1): Typical A-weighted sound power level, TE 1000-AVR 98 dB (A) Typical A-weighted emission sound pressure level, TE... - Page 11 5.1.2 Electrical safety 5.1.4 Power tool use and care a) Power tool plugs must match the outlet. Never a) Do not force the power tool. Use the correct modify the plug in any way. Do not use any ad- power tool for your application. The correct power apter plugs with earthed (grounded) power tools.
- Page 12 Hilti d) Always lead the supply cord and extension cord Service Center. Under unfavorable circumstances,...
-
Page 13: Before Use
tion, protective gloves and breathing protection while 5.3.4 Personal protective equipment the tool is in use. The user and any other persons in the vicinity must wear suitable eye protection, a hard hat, ear protec- 6 Before use Relax the tension on the side handle clamping band and slide it over the chuck and onto the cylindrical section at the front end of the power tool. - Page 14 Repeat the procedure if the hammering mechanism switch when the supply cord is plugged back in after does not begin to operate. unplugging, the power tool must be brought to Hilti NOTE Service immediately. As starting is electronically controlled, the power tool’s...
-
Page 15: Care And Maintenance
Clean the sealing lip by wiping it carefully and then grease it again lightly with Hilti grease. Check all external parts of the power tool for damage It is essential that the dust shield is replaced if the sealing at regular intervals and check that all controls operate lip is found to be damaged. -
Page 16: Troubleshooting
The chuck is not pulled back fully. Pull the chuck back as far as it will go and remove the insert tool. from the chuck. NOTE If the fault cannot be eliminated by the measures listed above, have the power tool checked by Hilti Service. -
Page 17: Disposal
10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or Hilti representative for further information. - Page 18 Hilti Corporation, Feldkircherstrasse 100, FL‑9494 Schaan Paolo Luccini Jan Doongaji Head of BA Quality and Process Management Executive Vice President Business Area Electric Tools & Accessories Business Unit Power Tools & Accessories 01/2012 01/2012 Technical documentation filed at: Hilti Entwicklungsgesellschaft mbH...
- Page 19 LI-9494 Schaan Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3150 | 0514 | 00-Pos. 8 | 1 Printed in Liechtenstein © 2014 248974 / A5 Right of technical and programme changes reserved S. E. & O...
Need help?
Do you have a question about the TE 1000-AVR and is the answer not in the manual?
Questions and answers