Hilti TE 1000-AVR Operating Instructions Manual
Breaker
Hide thumbs
Also See for TE 1000-AVR:
- User manual ,
- Operating instructions manual (235 pages) ,
- Original operating instructions (188 pages)
Related Manuals for Hilti TE 1000-AVR
Summary of Contents for Hilti TE 1000-AVR
- Page 1 TE 1000-AVR Operating instructions Mode d’emploi Manual de instrucciones Manual de instruções Printed: 16.05.2014 | Doc-Nr: PUB / 5165612 / 000 / 02...
- Page 2 This Product is Certified Ce produit est homologué Producto homologado por Este produto está registrado C US Printed: 16.05.2014 | Doc-Nr: PUB / 5165612 / 000 / 02...
- Page 3 Printed: 16.05.2014 | Doc-Nr: PUB / 5165612 / 000 / 02...
- Page 4 Printed: 16.05.2014 | Doc-Nr: PUB / 5165612 / 000 / 02...
- Page 5 Printed: 16.05.2014 | Doc-Nr: PUB / 5165612 / 000 / 02...
-
Page 6: Table Of Contents
ORIGINAL OPERATING INSTRUCTIONS TE 1000-AVR breaker 1 These numbers refer to the corresponding illustra- It is essential that the operating instructions tions. The illustrations can be found on the fold-out cover are read before the power tool is operated for pages. -
Page 7: Description
The power tool may be operated only when connected to a power supply providing a voltage and frequency in compliance with the information given on its type identification plate. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance. - Page 8 Grease Cleaning cloth Operating instructions Hilti toolbox 2.10 Using extension cords Use only extension cords of a type approved for the application and with conductors of adequate cross section. The power tool may otherwise lose performance and the extension cord may overheat. Check the extension cord for damage at regular intervals.
-
Page 9: Accessories, Consumables
Short designation Dust removal module TE DRS‑B Use the Hilti chisels or other tools listed below. With these you will achieve higher performance and longer lifetime as the power tool and chisels have been optimized as a system. TE‑S chuck /... -
Page 10: Technical Data
4 Technical data Right of technical changes reserved. NOTE The power tool is available in various voltage ratings. Please refer to the power tool’s type identification plate for details of its voltage, current and input power ratings. Rated voltage 120 V Rated current input 15 A Mains frequency... - Page 11 c) Hold power tool by insulated gripping surfaces, tached to a rotating part of the power tool may result in personal injury. when performing an operation where the cutting accessory may contact hidden wiring or its own e) Do not overreach. Keep proper footing and bal- cord.
-
Page 12: Before Use
Approval must be obtained from the site engineer should be checked at regular intervals at a Hilti or architect prior to beginning the work. Work Service Center. Under unfavorable circumstances,... -
Page 13: Operation
This ensures that flat chisels and shaped switch when the supply cord is plugged back in after chisels can always be set to the optimum working posi- unplugging, the power tool must be brought to Hilti tion. Service immediately. -
Page 14: Care And Maintenance
7.2.1 Chiseling 7.3 Chiseling tips 7.2.1.1 Working at low temperatures 7.3.1 Starting chiseling 7 NOTE Bring the tip of the chisel into contact with the workpiece The power tool must reach a minimum operating tem- about 3¹⁄₈" - 4" (80 - 100 mm) from its edge. perature before the hammering mechanism begins to 7.3.2 Reinforcing bars 8 operate. -
Page 15: Troubleshooting
Clean the sealing lip by wiping it Check all external parts of the power tool for damage carefully and then grease it again lightly with Hilti grease. at regular intervals and check that all controls operate faultlessly. -
Page 16: Disposal
NOTE If the fault can not be eliminated by the measures listed above, have the power tool checked by Hilti Service. 10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. - Page 17 Tel.: +423 / 234 21 11 Fax: +423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 4338 | 0514 | 00-Pos. 3 | 1 Printed in Germany © 2014 Right of technical and programme changes reserved S. E. & O.
Need help?
Do you have a question about the TE 1000-AVR and is the answer not in the manual?
Questions and answers