Hilti TE 1000-AVR Original Operating Instructions
Breaker
Hide thumbs
Also See for TE 1000-AVR:
- Operating instructions manual (235 pages) ,
- Manual (180 pages) ,
- Original operating instructions (176 pages)
Table of Contents
Advertisement
Quick Links
Printed: 08.10.2014 | Doc-Nr: PUB / 5165549 / 000 / 03
TE 1000-AVR
Bedienungsanleitung
Operating instructions
Mode d'emploi
Istruzioni d'uso
Manual de instrucciones
Manual de instruções
Gebruiksaanwijzing
Οδηγιες χρησεως
Használati utasítás
Instrukcja obsługi
Инструкция по зксплуатации
Návod k obsluze
Návod na obsluhu
Upute za uporabu
Uputstvo za upotrebu
Navodila za uporabo
Ръководство за обслужване
Instrucţiuni de utilizare
de
en
fr
it
es
pt
nl
el
hu
pl
ru
cs
sk
hr
sr
sl
bg
ro
he
Advertisement
Table of Contents
Related Manuals for Hilti TE 1000-AVR
Summary of Contents for Hilti TE 1000-AVR
- Page 1 TE 1000-AVR Bedienungsanleitung Operating instructions Mode d’emploi Istruzioni d’uso Manual de instrucciones Manual de instruções Gebruiksaanwijzing Οδηγιες χρησεως Használati utasítás Instrukcja obsługi Инструкция по зксплуатации Návod k obsluze Návod na obsluhu Upute za uporabu Uputstvo za upotrebu Navodila za uporabo Ръководство...
- Page 2 Printed: 08.10.2014 | Doc-Nr: PUB / 5165549 / 000 / 03...
-
Page 6: Table Of Contents
ORIGINAL OPERATING INSTRUCTIONS TE 1000-AVR breaker 1 These numbers refer to the illustrations. You can It is essential that the operating instructions find the illustrations at the beginning of the operating are read before the power tool is operated for instructions. -
Page 7: Description
The power tool may be operated only when connected to a power supply providing a voltage and frequency in compliance with the information given on its type identification plate. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance. - Page 8 Grease Cleaning cloth Operating instructions Hilti toolbox 2.10 Using extension cords Use only extension cords of a type approved for the application and with conductors of adequate cross section. The power tool may otherwise lose performance and the extension cord may overheat. Check the extension cord for damage at regular intervals.
-
Page 9: Accessories, Consumables
Short designation Dust removal module TE DRS‑B Use the Hilti chisels or other tools listed below. With these you will achieve higher performance and longer lifetime as the power tool and chisels have been optimized as a system. TE‑S chuck /... -
Page 10: Technical Data
TE‑S chuck / Width in Length in tool designa- Width (mm) Length (mm) inches inches tion Earth rod rammer TE‑S‑RD ³⁄₄" Inside ∅ ³⁄₄ 4 Technical data Right of technical changes reserved. Rated voltage 100 V 110 V 110 V 127 V Rated power input 1,750 W... -
Page 11: Safety Instructions
5 Safety instructions protection used for appropriate conditions will reduce 5.1 General Power Tool Safety Warnings personal injuries. WARNING c) Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to power Read all safety warnings and all instructions. Fail- source and/or battery pack, picking up or carrying ure to follow the warnings and instructions may result the tool. - Page 12 Always hold the power tool securely with both should be checked at regular intervals at a Hilti hands on the grips provided. Keep the grips dry, Service Center. Under unfavorable circumstances, clean and free from oil and grease.
-
Page 13: Before Use
c) If the work involves breaking right through, take 5.3.4 Personal protective equipment the appropriate safety measures at the opposite side. Parts breaking away could fall out and / or fall down and injure other persons. d) Approval must be obtained from the site engineer or architect prior to beginning the work. -
Page 14: Operation
If the power tool starts without pressing the on/off free from oil and grease. switch when the supply cord is plugged back in after unplugging, the power tool must be brought to Hilti 7.1 Preparing for use Service immediately. CAUTION... -
Page 15: Care And Maintenance
Break material away by increasing the angle to ap- 7.2.1.3 Adjusting chiseling power 6 prox. 90° as the chisel penetrates. Chiseling power can be reduced to approx. 70% by pressing the power level selector switch. The power level 7.3.4 Self-sharpening process 10 LED then lights up, indicating reduced power. -
Page 16: Troubleshooting
Clean the sealing lip by wiping it Check all external parts of the power tool for damage carefully and then grease it again lightly with Hilti grease. at regular intervals and check that all controls operate faultlessly. -
Page 17: Disposal
NOTE If the fault can not be eliminated by the measures listed above, have the power tool checked by Hilti Service. 10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. -
Page 18: Ec Declaration Of Conformity (Original)
Authorized assessment office (0044) TÜV NORD CERT GmbH Hannover office Am TÜV 1 30519 Hannover Germany Hilti Corporation, Feldkircherstrasse 100, FL‑9494 Schaan Paolo Luccini Jan Doongaji Head of BA Quality and Process Management Executive Vice President Business Area Electric Tools & Accessories Business Unit Power Tools &... - Page 19 Hilti Corporation LI-9494 Schaan Tel.: +423 / 234 21 11 Fax: +423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan Pos. 1 | 20140903 Printed: 08.10.2014 | Doc-Nr: PUB / 5165549 / 000 / 03...