Hilti TE 1000-AVR Operating Instructions Manual
Te 1000?avr / te 1500?avr breaker
Hide thumbs
Also See for TE 1000-AVR:
- Manual (176 pages) ,
- Operating instructions manual (126 pages) ,
- Original operating instructions (58 pages)
Related Manuals for Hilti TE 1000-AVR
Summary of Contents for Hilti TE 1000-AVR
- Page 1 TE 1000-AVR / TE 1500-AVR Operating instructions Mode d’emploi Manual de instrucciones Manual de instruções Printed: 08.07.2013 | Doc-Nr: PUB / 5070758 / 000 / 02...
- Page 2 This Product is Certified Ce produit est certifié Este producto esta certificado Este produto está certificado Printed: 08.07.2013 | Doc-Nr: PUB / 5070758 / 000 / 02...
- Page 3 Printed: 08.07.2013 | Doc-Nr: PUB / 5070758 / 000 / 02...
- Page 4 Printed: 08.07.2013 | Doc-Nr: PUB / 5070758 / 000 / 02...
-
Page 5: Table Of Contents
In these operating instructions, the designation “the Always keep these operating instructions to- power tool” always refers to the TE 1000-AVR and / gether with the power tool. or TE 1500-AVR breaker. Ensure that the operating instructions are... -
Page 6: Description
Make a note of this data in your operating instructions and always refer to it when making an enquiry to your Hilti representative or service department. Wear eye Wear a hard... - Page 7 To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance. Modification of the power tool or tampering with its parts is not permissible.
-
Page 8: Accessories, Consumables
Dust removal module TE DRS‑B Use the Hilti chisels or other tools listed below. With these chisels and tools you will achieve higher performance and longer lifetime as the power tool and chisels have been optimized as a system. TE‑S chuck /... -
Page 9: Technical Data
TE‑S chuck / Width in Length in tool designa- Width (mm) Length (mm) inches inches tion Pointed flat chisel TE‑S‑SPI 50 4¹⁄₂ 19¹⁄₈ Ballast bed chisel TE‑S‑TT 60 Shank TE‑S‑SS 11³⁄₄ Tamping plate TP‑STP 150 x 150 6 x 6 150/150 Bushing head TP‑SKHM 40... - Page 10 b) Avoid body contact with earthed or grounded controlled with the switch is dangerous and must be surfaces such as pipes, radiators, ranges and repaired. refrigerators. There is an increased risk of electric c) Disconnect the plug from the power source shock if your body is earthed or grounded.
- Page 11 Children must be instructed not to play with the should be checked at regular intervals at a Hilti power tool. Service Center. Under unfavorable circumstances, dampness or dust adhering to the surface of...
-
Page 12: Before Use
in the electric supply. This will prevent accidental b) Keep the workplace tidy. Objects which could restarting when the electric power returns. cause injury should be removed from the work- ing area. Untidiness at the workplace can lead to 5.3.4 Work area accidents. - Page 13 Repeat the procedure if the hammering mechanism switch when the supply cord is plugged back in after does not begin to operate. unplugging, the power tool must be brought to Hilti NOTE Service immediately. As starting is electronically controlled, the power tool’s...
-
Page 14: Care And Maintenance
Clean the sealing lip by wiping it carefully and then grease it again lightly with Hilti grease. Check all external parts of the power tool for damage It is essential that the dust shield is replaced if the sealing at regular intervals and check that all controls operate lip is found to be damaged. -
Page 15: Troubleshooting
The chuck is not pulled back fully. Pull the chuck back as far as it will go and remove the insert tool. from the chuck. NOTE If the fault cannot be eliminated by the measures listed above, have the power tool checked by Hilti Service. -
Page 16: Disposal
10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or Hilti representative for further information. - Page 17 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3150 | 1212 | 00-Pos. 3 | 1 Printed in Liechtenstein © 2012 Right of technical and programme changes reserved S. E. & O 248973 / A3 Printed: 08.07.2013 | Doc-Nr: PUB / 5070758 / 000 / 02...