Asko W6OO-SERIES Service Manual page 15

W600 AND W620 TEST PROGRAM W600 AND W620 TEST PROGRAM W600 AND W620 TEST PROGRAM
W600 AND W620 TEST PROGRAM W600 AND W620 TEST PROGRAM
1. Insert a jumper into E10 on the programmer.
2. Start program 3 (Fast wash).
3. EV2 (inlet valve for main wash water) allows
water into the machine up to the washing level.
4. Press the Super Rinse (
5. Heat up for 10 minutes or by 50° F (10° C).
6. Press the Economy (
7. Add more water to the wool level, about 1-1/2"
up the door.
8. Wash for 4 minutes.
9. Wash for 16 minutes, or until the # button is
pressed in again.
10. Run a long spin.
W600 AND W620 FAUL W600 AND W620 FAUL W600 AND W620 FAUL W600 AND W620 FAUL W600 AND W620 FAULT INDICA
If a fault occurs during a program cycle, this is
indicated by the program knob stopping in position
C or S after the program has finished or been
interrupted.
P P P P P osition C osition C osition C osition C osition C
If the program knob stops in position " after the
program has finished or been interrupted, this
indicates that one of the following problems has
occurred during the program cycle:
T h e r m i s t o r f a u l t T h e r m i s t o r f a u l t T h e r m i s t o r f a u l t T h e r m i s t o r f a u l t T h e r m i s t o r f a u l t
The washing program has finished without heating.
1. Check the fuses.
2. Measure the Ohms (see page 12).
Heating element fault Heating element fault
Heating element fault Heating element fault Heating element fault
The washing program has finished without heating.
1. Check the fuses.
2. Measure the thermistor Ohms.
3. Measure the heater relay Ohms.
P r o g r a m m e r f a u l t P r o g r a m m e r f a u l t P r o g r a m m e r f a u l t
P r o g r a m m e r f a u l t P r o g r a m m e r f a u l t
The washing program has been interrupted. Check
the fuses.
W600 AND W620 TEST PROGRAM AND FAULT INDICATIONS
) button.
2
) button.
E
T INDICATIONS T INDICA T INDICA T INDICA TIONS TIONS TIONS TIONS
W W W W W a t e r i n l e t f a u l t a t e r i n l e t f a u l t a t e r i n l e t f a u l t
a t e r i n l e t f a u l t a t e r i n l e t f a u l t
Indicates a fault in the water supply.
1. Make sure the water supply to the machine has
been turned on (cold fill only)
2. Check that the filter in the machine water inlet
is not blocked.
D r a i n i n g f a u l t D r a i n i n g f a u l t D r a i n i n g f a u l t D r a i n i n g f a u l t D r a i n i n g f a u l t
Draining has taken too long. Check the drain hose
and the drain pump as follows:
1. Make sure an object is not stuck in the drain
hose outlet. Clean out the hose.
2. Make sure the drain pump isn't blocked by
foreign objects. Clean out the pump.
3. Make sure the drain hose isn't kinked.
4. After solving the problem, run program 10
(Drain).
P P P P P osition S osition S osition S osition S osition S
If the program knob stops in position "S" after the
program has finished or been interrupted, this
indicates that a motor fault, a level sensor fault, or a
program fault has occurred during the program
cycle.
15