Safety Label Locations - MK Diamond Products CX-3 Owner's Manual & Operating Instructions

CX-3
®
OPERATION & SAFETY DECALS
The CX-3 Concrete Saw is equipped with a number of safety decals. These decals are provided for
®
operator safety and maintenance information. Should any of these operation or safety decals become
unreadable, replacements can be obtained by calling (800) 262-1575.
H
G
E
D
A
L
B
!
(A)
(B)
Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in
F
their composition may give off dust or mists containing crystalline silica. Silica is a basic
component of sand, quartz, brick clay, granite and numerous other minerals and rocks.
Repeated and/or substantial inhalation of airborne crystalline silica can cause serious
or fatal respiratory diseases, including silicosis. In addition, California and some other
authorities have listed respirable crystalline silica as a substance known to cause cancer.
! CAUTION
(C)
DO NOT
operate without
guards in place.
(3 of them)
! WARNING
In the event of
(D)
blade failure,
replace blade
guard
immediately.
! DANGER
The exhaust from this product
(E)
contains chemicals known to
the State of California to cause
cancer, birth defects or other
reproductive harm.
C
K
C
Location
A Motor Plate
Arm
B
Shaft Cover & Belt Guard
C
D Blade Guard
E Gas Tank/Side
F Gas Tank/Top
Gas Tank/Top
G
Gas Tank/Top Belt Guard
H
I Gas Tank/Side
J Frame/Back
K Frame/Front
Handle
L
Belt Guard
M
N Console
WARNING
Lethal exhaust
gases. Use only
in well ventilated
DO NOT operate
areas. DO NOT
this equipment
use indoors.
before reading
the owners'
!
manual!
When refueling
stop engine and
allow to cool.
WARNING
!
DO NOT overfill
tank.
!
DO NOT
touch hot
surface.
! CAUTION
Accidental start hazard.
Disconnect spark plug
prior to servicing.
FOR INFORMATION ON
SERVICE OR
WARRANTY
PLEASE CALL
1-800-474-5594
! CAUTION
Keep
hands and
feet clear.
Concrete Saw Warning Label Sheet Part# 166009
J
I
M
10
DANGER
WARNING
!
(F)
Handle bar NOT a lifting point.
NOTICE
!
WARNING
Overtensioning of belts
will result in premature
(G)
crank and/or bearing failure.
CAUTION
(H)
WARNING
Read entire operatorʼs manual before operating this Never use damaged
machine. Understand all warnings, instructions and blades or equipment.
controls. IF YOU DO NOT HAVE AN OPERATORʼS
MANUAL, CALL TOLL FREE 1-800-474-5594
Never operate this machine
Machinery Hazard - Always keep all guards in place in areas of combustible material.
and in good condition. Always keep all parts of your
body away from blade and all other moving parts.
Never allow blade exposure to exceed 180°.
Always use blades with a rated speed above the
blade shaft speed. Excessive speed can cause blade
(I) breakage. Verify speed by checking blade shaft RPM, Always wear safety approved hearing,
pulley diameters and blade flange diameter. eye, head and respiratory protection
(J)
(K)
Description
Read Manual
Proposition 65, Dust Warning
Guards in Place
Replace Blade Guard
Exhaust/Cancer
Lethal Exhaust
Refueling
Hot Surface
Accidental Start
Service
Hand & Feet Clear
Lifting Point
Overtensioning Belts
Machinery Hazard
SAFETY
(L)
(M)
Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities
contains chemicals known (to the State of California)
to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
(N)
• Lead from lead-based paints
• Crystalline silica from bricks and
cement and other masonry products
• Arsenic and chromium
from chemically-treated lumber
N