S.vibart (Stereo Vibrato) - Korg R3 Effect Manual

Effect guide
LFO Sync (LFO BPM Sync)
Specifies whether the internal LFO cycle will be syn-
chronized with the tempo specified by the [TEMPO]
knob or MIDI clock.
☞p.5 "LFO Sync (LFO BPM Sync)"
LFO Freq (LFO Frequency)
If "BPM Sync" is Off, this specifies the cycle at which the
waveform is switched in Hz units. The waveform length
specified by "Duration" will play as a loop, and the
waveform will switch at each cycle of the internal LFO.
LFO Cycle
Duration
In
Out
If this parameter is assigned to "Fx Knob," turning
"BPM Sync" On will switch the assignment to Syn-
cNote.
SyncNote (LFO Sync Note)
Sets the internal LFO frequency as a proportion of the
tempo set by the [TEMPO] knob if "BPM Sync" is On.
☞p.5 "SyncNote (LFO SyncNote)"
Key Sync (LFO Key Sync)
Specifies whether the LFO will be reset by note-on.
☞p.5 "Key Sync (LFO KeySync)"
IniPhase (LFO Init Phase)
Sets the starting location of the waveform if "Key Sync"
is Timbre.
☞p.5 "IniPhase (LFO Init Phase)"
LFOSpread (LFO Spread)
Sets the phase difference between the left and right
channels. When used for the master effect, this is dis-
played and can be set this parameter.
24
[Off, On]
[0.01...100.0Hz]
LFO Cycle /Duration
[8/1...1/64]
[Off, Timbre]
[000...180°]
only MFX
[–180...+180°]
28. S.Vibart
(Stereo Vibrato)
This effect causes the pitch of the input signal to shim-
mer. Using the AutoFade allows you to increase or de-
crease the shimmering speed.
Stereo In - Stereo Out
Left
Right
LFO LFO Shape
ModDepth (Modulation Depth)
Sets the depth of internal LFO modulation.
LFO Sync (LFO BPM Sync)
Specifies whether the internal LFO cycle will be syn-
chronized with the tempo specified by the [TEMPO]
knob or MIDI clock.
☞p.5 "LFO Sync (LFO BPM Sync)"
LFO Freq (LFO Frequency)
Sets the LFO speed.
☞p.5 "LFO Freq (LFO Frequency)"
SyncNote (LFO Sync Note)
Sets the internal LFO frequency as a proportion of the
tempo set by the [TEMPO] knob if "BPM Sync" is On.
☞p.5 "SyncNote (LFO SyncNote)"
LFO Wave (LFO Waveform)
[Saw, Square, Triangle, Sine, S&H]
Selects the internal LFO waveform.
☞p.5 "LFO Wave (LFO Waveform)"
LFOShape (LFO Shape)
☞p.5 "LFOShape"
Key Sync (LFO Key Sync)
Specifies whether the internal LFO will be reset by note-
on.
☞p.5 "Key Sync (LFO KeySync)"
IniPhase (LFO Init Phase)
Sets the starting location of the waveform if "Key Sync"
is Timbre.
☞p.5 "IniPhase (LFO Init Phase)"
only MFX
LFOSpred (LFO Spread)
Sets the LFO phase difference between the left and right
channels.
Dry / Wet
Vibrato
Vibrato
Dry / Wet
LFO Spread
[000...127]
[Off, On]
[0.01...100.0Hz]
[8/1...1/64]
[–63...+63]
[Off, Timbre]
[000...180°]
[–180...180°]