Korg R3 Effect Manual: S.moddly (stereo Modulation Delay); Tapeecho

Synthesizer / vocoder.
Hide thumbs
18. S.ModDly
(Stereo Modulation Delay)
This is a stereo modulation delay.
Stereo In - Stereo Out
Left
Delay
Feedback
Delay
Right
LFO Spread
LFO
BPM Sync (DelayTime BPM Sync)
Specifies whether the delay tempo will be synchronized.
☞p.13 LCR Delay "BPM Sync (Delay Time BPM Sync)"
TimRatio (Time Ratio)
[BPM Sync Off: 000.5...400.0% (OVER)
BPM Sync On: 012.5...400.0% (OVER)]
☞p.13 LCR Delay "TimRatio (Time Ratio)"
L Delay, R Delay (L, R Delay Time)
[BPM Sync Off IFX: 000...480msec
BPM Sync Off MFX: 000...680msec
☞p.14 StDelay "L Delay, R Delay (L, R Delay Time)"
Feedback
☞p.14 StDelay "Feedback"
ModDepth (Modulation Depth)
Sets the depth of internal LFO modulation.
LFO Freq (LFO Frequency)
Sets the internal LFO speed. Increasing this value will
result in a faster frequency.
LFO Spred (LFO Spread)
Sets the phase difference between the left and right
channels.
Dry / Wet
Dry / Wet
[Off, On]
BPM Sync On 1/64...1/1]
[000...127]
[000...127]
[0.01...100.0Hz]
[–180...+180°]
19. TapeEcho
This effect simulates a tape echo unit. The distortion and
tonal change typical of magnetic tape are also repro-
duced.
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Left
Feedback
+
Tape
Saturation
Trim
Pre Tone
High / Low Damp
Wah Flutter
Right
BPM Sync (DelayTime BPM Sync)
Specifies whether the delay tempo will be synchronized.
☞p.13 LCR Delay "BPM Sync (Delay Time BPM Sync)"
TimRatio (Time Ratio)
[BPM Sync Off: 000.5...400.0% (OVER)
BPM Sync On: 012.5...400.0% (OVER)]
☞p.13 LCR Delay "TimRatio (Time Ratio)"
Tap1Delay, Tap2 Delay(Tap1, Tap2 Delay Time)
[BPM Sync Off IFX: 000...980msec
BPM Sync Off MFX: 0000...1380msec,
Sets the delay times for Tap1 and Tap2.
☞p.13 LCR Delay "L Delay, C Delay, R Delay (L, C, R
Delay Time)"
Tap1Lvl, Tap2 Lvl (Tap1 Level, Tap2 Level)
Sets the Tap1 output level and Tap2 output level.
Feedback
Sets the Tap1 feedback amount.
HighDamp
Sets the damping amount in the high range.
Low Damp
Sets the damping amount in the low range.
Trim
Sets the input level.
Saturatn (Saturation)
Sets the distortion amount.
Waw Freq (Wah Flutter Frequency)
Sets the frequency at which pitch variation will occur in
Hz stepsl.
WawDepth (Wah Flutter Depth)
Sets the depth of pitch variation.
Pre Tone
Sets the tone of the input.
Spread
Sets the width of the stereo image of the effect sound.
☞p.13 LCR Delay "Spread"
Effect parameters
Dry / Wet
Tape1 Level
Delay
Spread
Tap2 Level
Dry / Wet
[Off, On]
BPM Sync On: 1/64... 1/1]
[000...127]
[000...127]
[000...100%]
[000...100%]
[000...127]
[000...127]
[0.01...100.0Hz]
[000...127]
[000...127]
[000...127]
17

Advertising

   Also See for Korg R3

   Related Manuals for Korg R3

Comments to this Manuals

Symbols: 0
Latest comments: