We appreciate your confidence in XTERRA Fitness and we will always remember that you are the reason that we are in business. Please complete and mail your registration card today and enjoy your new elliptical.
Serial Number Register Your Purchase The self-addressed product registration card must be completed in full and returned to XTERRA Fitness. You can also go to www.xterrafitness.com/warrantyreg.html to register online. Power This product uses an external power supply. The power supply must be plugged into the power jack, located on the front of the unit near the stabilizer tube.
Failure to follow all guidelines may compromise the effectiveness of the exercise experience, expose yourself (and possibly others) to injury, and reduce the longevity of the equipment. SAVE THESE INSTRUCTIONS - THINK SAFETY! CAUTION!! Please be careful when unpacking the carton. FS1.5 Elliptical...
Page 5
Hardware Step 2 #43. 5/16” x 3/4” #100. 8.5 x 23 x 1.5T Button Head Socket Flat Washer Bolt (1 pc) (1 pc) #55. 5/16” #56. 5/16” x 1-3/4” Nyloc Nut Button Head Socket (2 pcs) Bolt (2 pcs) FS1.5 Elliptical...
Phillips Head Screw Driver (68). 5. Secure the Front Stabilizer (12) and Rear Stabilizer (13) with four Button Head Socket Bolts (43), four Split Washers (46) and four Flat Washers (44). Tighten using the M5 Allen Wrench (68). FS1.5 Elliptical...
Page 8
2. Slide the Swing Arm Axle (22) through the console mast bushings, then through the Handle Bar Cover (78) and Lower swing arm (6). Attach with one Button Head Socket Bolt (43) and one Flat Washer (100). Tighten using the M5 Allen Wrenches (68). FS1.5 Elliptical...
Page 9
Note: If there is a gap after assembling the swing arm, please install a C-ring at Location A as shown above. 3. Install the outer covers (79) with four Sheet Metal Screws (52). Tighten using the Phillips Head Screw Driver (68). FS1.5 Elliptical...
Page 10
3. Attach the Pedal Arm Covers (85, 86) onto the Pedal Arm Assembly (2) with one Sheet Metal Screw (52). Tighten using the Phillips Head Screw Driver (68). 4. Repeat steps 1-3 above for the left side pedal arm assembly. FS1.5 Elliptical...
1 to 6. A score of 1 is an indication of a high level of fitness and a score of 6 indicates poor condition. MODE: Press to switch display from RPM to SPEED, ODO to DIST, WATT to CALORIES. FS1.5 Elliptical...
Using UP / DOWN KEY you may set the desired time value. Press ENTER KEY to input value. Flashing prompt will move to the next parameter. Continue use of UP / DOWN KEY. Press START / STOP to start workout. FS1.5 Elliptical...
Page 13
40-250 Watt control program. Target Heart Rate will be based on Age. When heart rate ex- ± 10-99 ceeds Target Heart Rate, the number of heart rate will flash. Setting Paramters for Target Pulse 60-220 ± Heart Rate. FS1.5 Elliptical...
When any one of the workout parameters counts down to zero the console emits a beep sound and the workout stops automatically. Press START KEY to continue the workout to reach the unfinished workout goals set. FS1.5 Elliptical...
Type 8 is from 40% to 44%. Type 9 is from 45% to 50%. BMR: Basal Metabolic Rate is the amount of daily energy expended at rest. BMI: Body Mass Index is a general body type based on height and weight. FS1.5 Elliptical...
60 seconds then it will decrease the resistance load 1 level every 10s. When any one of the workout parameters counts down to zero the console emits a beep sound and the workout stops automatically. Press START KEY to continue the workout to reach the unfinished workout goals set. FS1.5 Elliptical...
Page 18
60 seconds then it will decrease the resistance load 1 level every 10 seconds. When any one of the workout parameters counts down to zero the console emits a beep sound and the workout stops automatically. Press START KEY to continue the workout to reach the unfinished workout goals set. FS1.5 Elliptical...
Effective August 1, 2012 - ELLIPTICAL LIMITED WARRANTY XTERRA Fitness Inc. warrants all its home use elliptical parts for a period of time listed below, from the date of retail sale, as determined by a sales receipt or in the absence of a sales receipt, eighteen (18) months from the original factory shipping date. XTERRA Fitness’s responsibilities include providing new or remanufactured parts, at XTERRA Fitness’s option, and technical support to our independent...