Related Manuals for Xterra FS3.5
Summary of Contents for Xterra FS3.5
- Page 1 FS3.5 ELLIPTICAL OWNER’S MANUAL PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING YOUR NEW ELLIPTICAL...
-
Page 2: Table Of Contents
XTERRA Fitness will do all we can to make your ownership experience as pleasant as possible for many years to come. If you have questions, or if parts are missing or damaged, or you require customer service, call (870) 336-4286. -
Page 3: Product Registration
Serial Number Register Your Purchase The self-addressed product registration card must be completed in full and returned to XTERRA Fitness. You can also go to www.xterrafitness.com/warrantyreg.html to register online. Power This product uses an external power supply. The power supply must be plugged into the power jack, located on the front of the unit near the stabilizer tube. -
Page 4: Important Safety Instructions
Failure to follow all guidelines may compromise the effectiveness of the exercise experience, expose yourself (and possibly others) to injury, and reduce the longevity of the equipment. SAVE THESE INSTRUCTIONS - THINK SAFETY! CAUTION!! Please be careful when unpacking the carton. FS3.5 Elliptical... - Page 5 FS3.5 Assembly Pack Checklist Hardware Step 1 #77. 3/8” x 3” Carriage Bolt (2 pcs) #82. M5 x 15mm #96. 3/8” #80-1. 5/16 ” x 15mm Phillips Head Cap Nut Button Head Socket Bolt Screw (4 pcs) (2 pcs) (2 pcs) #104-1.
-
Page 6: Assembly Tools
#113. 5/16” x 23 x 1.5T Curved Washer (4 pcs) Assembly Tools #115. 13 & 14 mm Wrench (1 pc) #116. 12 mm Wrench (1 pc) #118. Combination 5mm Allen Wrench & Phillips Head Screw Driver (1 pc) FS3.5 Elliptical... -
Page 7: Fs3.5 Assembly Instructions
FS3.5 Assembly Instructions Front Stabilizer and Connecting Arms Hardware Step 1 #77. 3/8” x 3” Carriage Bolt (2 pcs) #80-1. 5/16” x 15mm Button Head Socket Bolt (2 pcs) #82. M5 x 15mm Phillips Head Screw (4 pc) #96. 3/8”... - Page 8 Computer cable and the two Handpulse W/Cable Assemblies (40) on the Console. Secure the Console on the Console Assembly (35) four Phillips Head Screws (84) by using Combination M5 Allen Wrench & Phillips Head Screw Driver(118). Pay attention to Avoid- ing scratching the cables. FS3.5 Elliptical...
- Page 9 2. Release rod end shafts (18) which are on left and right connecting arms. Connect the connecting arm with lower handle bar and secure with rod end shafts (18) and the screw by using Combination M5 Allen Wrench & Phillips Head Screw Driver (118) and 12m/m_Wrench (116). FS3.5 Elliptical...
- Page 10 Head Screw Driver (118). Repeat the same procedure for the right side. 3. Connect the Console Mast Cover (L)(42) and the Console Mast Cover (R)(43) together on the Console Mast and secure with two Sheet Metal Screws (87) by using Combination M5 Allen Wrench & Phillips Head Screw Driver(118) FS3.5 Elliptical...
-
Page 11: Operation Of Your Console
Operation of Your Console FS3.5 Console Key Functions START / STOP: 1. Starts & Pauses workouts. 2. Starts body fat measurement. 3. Holding key for 3 seconds will reset all functions and values to zero. DOWN: Decreases value of selected workout parameter: TIME, DISTANCE, etc. During the workout it will decrease the resistance load. - Page 12 Using UP / DOWN KEY you may set the desired time value. Press ENTER KEY to input value. Flashing prompt will move to the next parameter. Continue use of UP / DOWN KEY. Press START / STOP to start workout. FS3.5 Elliptical...
-
Page 13: Program Operation
START / STOP to start workout. Note: When any One of the workout parameters counts down to zero the console emits a beep sound and the workout stops automatically. Press START KEY to continue the workout to reach the unfinished workout goals set. FS3.5 Elliptical... - Page 14 User can use UP / DOWN key to adjust the watt value during workout. FS3.5 Elliptical...
- Page 15 Pre-Set Programs (P2 - P13) FS3.5 Elliptical...
- Page 16 ENTER until finished (10 times total). Press START / STOP to start workout. Note: When any one of the workout parameters counts down to zero the console emits a beep sound and the workout stops automatically. Press START KEY to continue the workout to reach the unfinished workout goals set. FS3.5 Elliptical...
- Page 17 Normally the transmitter will be oriented so the XTERRA Fitness logo is right side up. 6. The antenna that picks up your heart rate is very sensitive. If there is an outside noise source, turning the whole machine 90 degrees may de-tune the interference.
- Page 18 60 seconds then it will decrease the resistance load 1 level every 10 seconds. When any one of the workout parameters counts down to zero the console emits a beep sound and the workout stops automatically. Press START KEY to continue the workout to reach the unfinished workout goals set. FS3.5 Elliptical...
-
Page 19: Manufacturer's Limited Warranty
Effective August 1, 2012 - ELLIPTICAL LIMITED WARRANTY XTERRA Fitness Inc. warrants all its home use elliptical parts for a period of time listed below, from the date of retail sale, as determined by a sales receipt or in the absence of a sales receipt, eighteen (18) months from the original factory shipping date. XTERRA Fitness’s responsibilities include providing new or remanufactured parts, at XTERRA Fitness’s option, and technical support to our independent... - Page 20 3000 Nestle Road Jonesboro, AR 72401 - Phone:870-336-4286 - Fax:870-935-7611 www.xterrafitness.com ©2014 All RIghts Reserved. FS3.5 Owner’s Manual...