Table of Contents
Advertisement
Quick Links
!
WARNING
!
WARNING
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury or loss of life.
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light the appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from
a neighbor's phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed
by a qualified installer, service agency or the
gas supplier.
4000607-16
© 2010 Miles Industries Ltd. All rights reserved.
Model RF24DN/DP
Direct Vent Fireplace Insert
Installation and Owner's Manual
WARNING
HOT GLASS WILL
HOT GLASS WILL
HOT GLASS WILL
CAUSE BURNS.
CAUSE BURNS.
CAUSE BURNS.
DO NOT TOUCH GLASS
DO NOT TOUCH GLASS
DO NOT TOUCH GLASS
UNTIL COOLED.
UNTIL COOLED.
UNTIL COOLED.
NEVER ALLOW CHILDREN
NEVER ALLOW CHILDREN
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
TO TOUCH GLASS.
TO TOUCH GLASS.
Manufactured by
MILES INDUSTRIES LTD., British Columbia, Canada
www.valorfireplaces.com
INSTALLER: Leave this manual
with the appliance.
CONSUMER: Retain this manual
for future reference.
Please read this manual BEFORE installing
and operating this appliance.
This appliance may be installed in an
after-market permanently located,
manufactured (mobile) home where not
prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certified kit is used.
This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.
This appliance is suitable for installation in a
bedroom or bed sitting room.
Massachusetts: The piping and final
gas connection must be performed by a
licensed plumber or gas fitter in the State of
Massachusetts.
Patents Pending
Advertisement
Table of Contents
Related Manuals for Valor RetroFire RF24DN
Summary of Contents for Valor RetroFire RF24DN
- Page 1 Patents Pending Model RF24DN/DP Direct Vent Fireplace Insert Installation and Owner’s Manual WARNING WARNING WARNING HOT GLASS WILL HOT GLASS WILL HOT GLASS WILL CAUSE BURNS. CAUSE BURNS. CAUSE BURNS. DO NOT TOUCH GLASS DO NOT TOUCH GLASS DO NOT TOUCH GLASS UNTIL COOLED.
- Page 2 Thank You ... For purchasing a Valor Retrofire. Your new radiant gas heater is a technical appliance that must be installed by a qualified dealer. Each Retrofire is fully tested during the production process for your safety and comfort. Your unit has been professionally installed by:...
-
Page 3: Table Of Contents
Table of Contents Safety and Warning Information..............4 ◊ Specifications ....................5 ◊ Dimensions ....................6 Vent Configurations ..................7 Vent Termination ....................8 Existing Fireplace Preparation ..............10 Supply Gas Installation ................11 Vent Liner Rough-in ..................12 Appliance Preparation .................12 Firebox Installation ..................13 Ceramic Fuel Bed Installation ..............15 Window Refitting and Checking ..............17 ◊... -
Page 4: Safety And Warning Information
Safety and Warning Information READ and UNDERSTAND all instructions carefully This unit MUST be used with a vent system as before starting the installation. FAILURE TO FOLLOW described in this installation manual. NO OTHER vent these installation instructions may result in possible fire system or components MAY BE USED. -
Page 5: Specifications
Safety and Warning Information Operating Your Fireplace for the First Time It is also possible that these vapors could set off any smoke detection alarms in the immediate vicinity. When operating your new fireplace for the first time, These vapors are quite normal on new appliances. We some vapors may be released due to the burning of recommend opening a window to vent the room. -
Page 6: Dimensions
Dimensions Dimensions 24-1/2” 24-3/8” 17-1/4” 8” 7-5/8” 1225VFB Ventana Fret (Black) 3” dia. 3” dia. RA24TB Fret (Black) Inlet 25-1/2” 27” Gas Inlet 11” 3/8” NPT Female 10” RA24CV Fret (Vintage Iron) RA24AV Fret (Vintage Iron) Optional Frets Control Valve Location 1”... -
Page 7: Vent Configurations
Vent Configurations Allowable Vent Configurations Where possible, avoid joints in flex pipe. If joints are required, use only connectors approved by the The RF24 is certified for use with approved 3” diameter manufacturer of the flex pipe. Field fabricated joints are flexible venting installed into an approved existing solid not allowed. -
Page 8: Vent Termination
Vent Termination The RF24 is approved for Vertical Co-Linear Termination Only. Two 3” diameter liners 10” dia. are required from top to bottom. The vent liners must be connected to the proper collars (intake and exhaust) or the unit will not operate properly. The method of flashing will depend on whether the liners are installed into a rectangular masonry or round factory-built solid-fuel burning chimney. -
Page 9: Vent Terminal Location
Vent Termination Vent Terminal Location The venting system for this appliance is considered to be a Special Venting System. The rule in the Installation Code CAN/CGA–B149 requiring a minimum vent height of 2 feet above any portion of a building within 10 feet does not, therefore, apply. -
Page 10: Existing Fireplace Preparation
Existing Fireplace Preparation A few points must be considered before inserting the RF24 into an existing fireplace cavity. Generally, no modifications are allowed to the existing fireplace that will compromise the integrity of the existing fireplace. Components that are bolted or screwed on such as dampers or baffles may be removed to accommodate the installation of the RF24 engine. -
Page 11: Supply Gas Installation
Supply Gas • It’s preferable to rough-in the gas line at this point before proceeding with the firebox installation. • The gas supply inlet connection is a 3/8” NPT female connector. For detailed location of this connector, see drawing in section Dimensions. If a circulating fan or isolating valve is to be installed, adjust the routing of the gas line to suit. -
Page 12: Vent Liner Rough-In
Vent Liner Rough-in Rough-in the two 3” diameter vent liners into existing chimney system being careful not to tear or damage the liners in the process. It may be easier to install both liners at the same time rather than one at a time. Leave plenty of liner at the bottom end if the Heater will be connected while on the hearth (see diagram). -
Page 13: Firebox Installation
Firebox Installation Connection of liners to firebox Trim liners if necessary and connect to the firebox either while the firebox is on the hearth or with the firebox in the cavity. Use gear clamps provided to connect the liners to the firebox. If the liners are connected with the firebox on the hearth, it will be necessary to pull the slack liner up from the top of the chimney after the firebox is installed. -
Page 14: Side View
Firebox Installation Leveling the firebox in the hearth The backside of each support leg has a leveling bolt. If necessary, adjust the level of the firebox in the hearth. Fret bracket Leveling Leveling Front Back bolt bolt Leveling bolt Front View Side View Burner Module Reinstallation Note: If the circulating fan is to be installed it should be done at this point before installing the burner... -
Page 15: Ceramic Fuel Bed Installation
Firebox Installation Top Convection Baffle Installation Position the firebox as far back as possible within the existing fireplace to allow ample space at front for the fret and to allow convection air to flow under the smoke curtain of the existing fireplace. Position the top convection baffle with the threaded studs pointing downwards into the slots at the top of the firebox. - Page 16 Ceramic Fuel Bed Installation Ceramic Log Set Installation Carefully remove the ceramic logs from the packaging taking care not to damage them. Install the logs as described below. Please note that the Rear Log will have a different position depending of the gas type. The position of the logs is critical to insure the good performance of the appliance.
-
Page 17: Window Refitting And Checking
Window Refitting and Checking Hook the window over the top edge of the firebox, and fasten the bottom two spring loaded bolts by pushing in and turning 90 degrees. Check that the window moves freely against the spring by pulling out at the bottom. -
Page 18: Operation Check And Aeration Adjustment
Operation Check and Aeration Adjustment Turn the fireplace up and down using the remote control to confirm that the full range of inputs is achieved. Light the fire and allow to warm up for 10–15 minutes to evaluate Air Shutter the flame picture. -
Page 19: Owner's Information
Owner’s Information The window can be removed for cleaning by rotating CAUTION the two fastening studs at the bottom corners 90 Your fireplace becomes very hot when operating. degrees to release, and swinging the bottom of the Avoid placing decorating objects sensitive to heat window unit outwards to unhook the top edge. -
Page 20: Remote Control Operation
Owner’s Information Batteries Replacement General Servicing CAUTION If your appliance needs to be serviced, contact your supplier quoting the model number. It will be helpful if DO NOT USE a screwdriver or other metallic object the appliance serial number can also be quoted. This is to remove the batteries from the receiver or the on the rating plate, which is attached to the unit. -
Page 21: Battery Replacement
Remote Control Operation Setting the flame Use this setting when you want a particular flame level. For instance, you want to watch flames burn at their highest level and you don’t mind if the room is too hot. 1. To raise the flame, press and hold the ▲ button until the flame gets to the desired level. -
Page 22: Options
Termination—Miles Industries’ 559CLT Co-Linear stores carrying safety products for children. Termination and 559SFK Square Flashing Kit are Approved Venting Components APPROVED DIRECT VENT SUPPLIERS FOR VALOR MODELS 739 & RF24DV Venting Parts Code / availability by Manufacturer Venting Parts Description Standard Co-axial... -
Page 23: Lighting Instructions
Lighting Instructions FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot, which must be lighted by hand. When lighting the pilot, follow these instructions exactly. -
Page 24: Warranty
Warranty If you have a problem with this unit, please contact your dealer or supplier immediately. Under no circumstances should you attempt to service the unit in any way by yourself. The warranties in paragraphs 1 and 2 are provided only to the first purchaser/user of this unit, are not transferable and are subject to the conditions and limitations in paragraphs 3, 4 and 5. -
Page 25: Parts
Parts PART PART DESCRIPTION DESCRIPTION NUMBER NUMBER Firebox Assembly 400634AH 2-Flame Pilot Hood 4000730 Restrictor (2) 400767 Electrode 720A543 Convection Baffle 4000744 Pilot Tube 4000732 Fret Support LH 4000693 Straight Connector 544079 Wing Nut (2) 4000741 Maxitrol Valve GV34 4000056 Leg LH 4000662 Valve Cover... - Page 26 Parts 8a, 8b 14a, 12a, 12b 53a, 53b 54a, 54b 34a, 29a, 29b 40a, 40b...
- Page 27 Thank You ... For purchasing a Valor by Miles Industries. Your new radiant gas heater is a technical appliance that must be installed by a qualified dealer. Please circle where appropriate - ask your installer if in doubt:Information provided will be used for customer records only.
- Page 28 Fold here Postage needed Miles Industries Ltd. 190 - 2255 Dollarton Highway North Vancouver, BC V7H 3B1 Canada Online Warranty registration at www.valorfireplaces.com Were you given all documentation and manuals for your product? Thank you for choosing a Valor Product...