Easy Steps To Operate Your Angelcare ® Monitor; Warnings; Instructions - Angelcare Movement Monitor Instruction Manual

4 EASY STEPS TO OPERATE YOUR ANGELCARE
STEP 1. SENSOR PAD
• Position Sensor Pad as illustrated (Figures 1 and 2). The printed side of Sensor Pad MUST face up. DO NOT tuck thick bedding
under the edges of the mattress.
• The Sensor Pad must rest on a completely flat and firm surface. If the crib has a spring or slat base, place a hard board between
the crib base and the Sensor Pad measuring at least 13" x 13" (33x33 cm) and 1/4 inch (6 mm) thick.
• The Sensor Pad works with all baby bed sizes and all mattresses, except memory foam mattresses or mattresses with a hollow
frame. You will need to test your Sensor Pad after the set-up is completed.
STEP 2 MONITOR
• Insert 2 AA batteries into Monitor.
• Connect the Sensor Pad cord to the monitor (Figure 3).
• On the side of the Monitor, select 1 of the 2 functions of how you want to monitor your baby:
"Tic" On: To see green movement indicator light flash AND hear a "Tic" sound with every movement baby makes.
"Tic" Off: Same as above BUT without the "Tic" sound.
NOTE: The sensitivity adjustment has been preset. DO NOT ADJUST UNLESS NECESSARY. If poor capture of movement (red flashing
light) or false alarm occurs, consult the Movement Sensitivity Adjustment section.
STEP 3 TO USE MONITOR
• Place baby in crib and switch Monitor to the ON position. When removing baby from crib, switch Monitor to the OFF position. If
you forget to switch OFF, a "pre-alarm Tic" will sound after 15 seconds as a reminder.
STEP 4 BATTERY MODE
• The Angelcare Movement Monitor is battery operated. Batteries will last approximately 3 to 4 months. When monitor produces
®
a rapid clicking sound, change batteries promptly.
NOTE:
• Test your Angelcare Monitor BEFORE first-time use and then on a periodic basis.
®
• When monitor is in use, DO NOT use crib mobile or other crib accessories that produce vibrations. Alarm will not sound as monitor is
still detecting movement.
• The Angelcare Monitor is perfectly safe. The Sensor Pad and the cord are entirely passive. They carry no electrical current and do
®
not radiate any form of energy.
• The Sensor Pad works with all baby bed sizes and all mattresses, except memory foam mattresses or mattresses with a hollow frame.
You will need to test your Sensor Pad after the set-up is completed.

Warnings

This product is NOT a substitute for direct supervision of your
•
baby. Check your baby's activities at regular intervals.
• The Sensor Pad may detect movement from many sources from
BOTH inside and outside your baby's room, for example: fans,
washing machines, loud music, etc. Ensure that all vibration
sources are eliminated before using the Angelcare
Avoid contact with crib when monitor is in use. Refer to the
Movement Sensitivity Adjustment and Troubleshooting sections.
• ALWAYS place Monitor on flat surface in an upright position, away
from baby's reach.
• This product should be serviced by qualified personnel. There are
no user serviceable parts inside monitor. Refer all service
questions to Angelcare.

Instructions

RETAIN INSTRUCTIONS: Keep user's manual for future reference.
WATER, MOISTURE AND HEAT DAMAGE: Keep all components away
from water (sink, bath tub, swimming pool) and places that emit heat
(stove, radiator).
VENTILATION: ALWAYS place Monitor on flat surface in an upright
position so that air can flow freely around it.
Monitor.
®
CORD PROTECTION: Avoid damage to the Sensor Pad cord. The cord
is long enough to route so that it is not likely to be walked on or
pinched by items placed upon or against it.
CLEANING: Disconnect Monitor before cleaning. DO NOT immerse in
water. Use a dry cloth to keep Monitor free from dust. DO NOT spray
with cleaning products or solvents. Wipe Sensor Pad with a very
slightly damp cloth with an antiseptic or mild detergent.
OBJECT AND LIQUID ENTRY: Care should be taken so that objects do
not fall onto Monitor and that liquids are not spilled into either
Monitor or Sensor Pad through its openings.
NON-USE PERIODS: When not using monitor for long periods,
remove the batteries from Monitor.
9
MONITOR
®