Advertisement
Quick Links
Advertisement
Related Manuals for Vanraam O-Pair
Summary of Contents for Vanraam O-Pair
- Page 1 User manual O-Pair² Van Raam BV Aaltenseweg 56 7051 CM Varsseveld The Netherlands 06.13...
- Page 2 Aaltenseweg 56 7051 CM Varsseveld The Netherlands Tel. : +31 (0)315 257370 E-mail : info@vanraam.nl Internet : www.vanraam.nl Conformity Van Raam declares as manufacturer that the O-Pair² bicycle has been produced in accordance with the 93/42/EEG guidelines. User manual O-Pair² 06.13...
- Page 3 Also the local traffic rules should always be complied with. All other use, including damage or physical injuries due to this, are not the manufacturer's responsibility. User manual O-Pair² 06.13...
- Page 4 Use the parking brake if you or your passenger is getting on or off the bike. Never drive without a passenger. This will cause instability of the bike and will lead to dangerous situations. User manual O-Pair² 06.13...
- Page 5 If an optimal adjustment of the bicycle, as defined in the instructions, is not possible, you can contact your dealer for a fitting solution. The brakes are correctly adjusted as standard and can only be adjusted by the dealer during periodic maintenance. User manual O-Pair² 06.13...
- Page 6 Do not pull out the saddle pin further than the marking. The tube will not go into the shank deep enough and will risk coming off. This can lead to MIN INSERT serious injuries. User manual O-Pair² 06.13...
- Page 7 To tilt the handle bars: 1. Slightly loosen the screw with an Allen key. 2. Put the handle bars in the desired position and then tighten the screw very firmly again. User manual O-Pair² 06.13...
- Page 8 3. Loosen the four screws slightly on both sides using a socket wrench. 4. Turn the side supports to the body, in such a way that the passenger is sitting most comfortably. Tighten the screws again. User manual O-Pair² 06.13...
- Page 9 To do this: Loosen the screws completely with a socket wrench and move the foot support to the desired position. Tighten the screws again. User manual O-Pair² 06.13...
- Page 10 Adjust the seat depth To adjust the seat depth of the chair to the passenger: 1. Slightly loosen both nuts with a spanner. 2. Slide the seat so it fits the legs of the passenger. Fasten the nuts again. User manual O-Pair² 06.13...
- Page 11 Belts for children are adjusted over the side supports and then through the upholstery. For adults, the belts are adjusted over the chair. Belt for Belt for children adults User manual O-Pair² 06.13...
- Page 12 2. Tighten the belt till it fits the body of the passenger. Then buckle it. Belt for children The child’s belt slides through the clamp on the front side of the back, behind the upholstery. Remove the upholstery and slip the belt through the clamp. User manual O-Pair² 06.13...
- Page 13 Make sure the small spring is secured in the grip. 5. Lower the support wheel by pulling out the knob. 6. Remove the safety pin. User manual O-Pair² 06.13...
- Page 14 Remove the bicycle part from the coupling. Caution: This is heavy. Hold the frame firmly with both hands. 10. Place the rear end on the stand. To assemble the bicycle again, follow these steps in reverse order. User manual O-Pair² 06.13...
- Page 15 2. Push the pin until the handle bars are released. 3. Pull out the handlebars from the tube. 4. Now fold the back rest to the front. Notice that the cables are not bent when folding! User manual O-Pair² 06.13...
- Page 16 When the last red light flashes, the battery is empty and the engine will not support you any longer while cycling. User manual O-Pair² 06.13...
- Page 17 Connect the charger plug into the socket. The red light on the charger will light up. Depending on the battery level, the charging time is about 3 hours. If the green light is on, the battery is charged. User manual O-Pair² 06.13...
- Page 18 Push the handle forward and close the lock. It is also possible to charge the battery while it is still in the holder. User manual O-Pair² 06.13...
- Page 19 Backup battery (optional) The bike can be supplied with a second battery. To activate the second battery (when the first battery is empty) turn on the switch under the luggage carrier in order to activate the battery. User manual O-Pair² 06.13...
- Page 20 With the red button you shut down the system. If the system is not used, it will automatically shut itself down after a period of time. When walking backwards with the bicycle, always turn off the motor. User manual O-Pair² 06.13...
- Page 21 When charging, first connect the plug to the charging point on the bicycle and then put the plug in the wall socket! When charged, first take the plug from the wall socket and then disconnect the charger from the bicycle! User manual O-Pair² 06.13...
- Page 22 Only use the charger in non-humid indoor spaces. Below 5 degrees Celsius the charger will not function properly. In that case it is advisable to charge the batteries indoors. Extra accessories are available at your dealer. User manual O-Pair² 06.13...
- Page 23 6 hours, after the charge light has expired. For the lifespan of the batteries, we recommend charging the lamp once every 3 months, when not used for a longer period. User manual O-Pair² 06.13...
- Page 24 Always use the parking brake if you park the bicycle and leave it behind. To operate the parking brake, squeeze the left brake [A] and lock it with the pin [B]. By squeezing the brake again it will unlock itself. User manual O-Pair² 06.13...
- Page 25 If a component fails, it can lead to very dangerous situations. This can lead to damage or injuries to the user of the bicycle. Any form of tearing, scratching or changing of colour is an indication that the part should be replaced. User manual O-Pair² 06.13...
- Page 26 Technical details Length (cm) Width (cm) Boarding height (cm) 24“ Front wheel 20“ Back wheel Weight (kg) From 40 Max. load luggage rack (kg) Total max. load (kg) Brakes, front Disk brakes Brakes, back Cantilever brakes User manual O-Pair² 06.13...
- Page 27 Wipe the chain with a cloth, treat it with grease or spray and remove any excess lubricant with a rag. Other parts should not be treated with a lubricant. User manual O-Pair² 06.13...
- Page 28 In that case the rim should be replaced, because it can lead to loss of brake function or even a crack in the rim, which can lead to all kinds of dangerous consequences. User manual O-Pair² 06.13...
- Page 29 The guarantee as well as the product liability in general expires if the instructions stated in this manual are not followed. This is also the case if unauthorized maintenance is carried out or if technical changes or additions are made without permission of Van Raam. User manual O-Pair² 06.13...
- Page 30 Frame number The frame number is printed on the sticker. This sticker is located on the frame, see the image below. Example sticker: Frame number Position of sticker: on the back of the saddle tube User manual O-Pair² 06.13...