Subscribe to Our Youtube Channel
Related Manuals for Rascal Rascal AutoGo
Summary of Contents for Rascal Rascal AutoGo
- Page 1 Rascal AutoGo™ Owner’s Manual The Rascal Company 1 Mobility Plaza., Sewell, NJ 08080...
- Page 2 Your Rascal AutoGo has been thoroughly tested and will give you years of good service and pleasure, providing you follow the instructions and precautions in this manual.
-
Page 3: Table Of Contents
Safety Information ................... 1 Curbs and Small Obstacles ............23 Freewheel Operation ..............23 Getting to Know Your Rascal AutoGo ..........5 Automatic Folding and Unfolding ............24 Illustration 1 — Rascal AutoGo Components ..........6 Folding Instructions ................24 Initial Set-up .................... - Page 4 Rascal AutoGo Owner’s Manual Title Page Title Page Maintenance ....................38 Illustration 17— Cable Turnbuckle Adjustment ........ 42 Preventative Maintenance ................ 38 Drivetrain ....................43 Frame Inspection .................. 38 Seat Frame Cams .................. 43 Headlight ....................39 Replacing Clock Battery ..............44 Lubrication .....................
- Page 5 No liability is assumed with respect to the use of any information contained in this publication. While every precaution has been taken in the preparation of this publication, The Rascal Company, assumes no responsiblity for errors or omissions nor is any liablity assumed for damages resulting from the use of information contained in this publication.
-
Page 6: Safety Information
Rascal AutoGo Owner’s Manual Safety Information Read and understand these Warnings and the entire manual before using your Rascal AutoGo. Failure to follow these instructions may result in damage to the vehicle or serious injury. IMPORTANT! 1. DO NOT exceed the specifications of this unit, modify turned “OFF”, completely stopped, and when it is on a... - Page 7 Rascal AutoGo Owner’s Manual 9. DO NOT back down an incline or allow the unit to be the unit. backed down an incline. 17. USE EXTRA CAUTION when climbing inclines 10. DO NOT turn off the power while the unit is moving.
- Page 8 Rascal AutoGo Owner’s Manual Important Information Regarding Electromagnetic Interference (EMI) It is very important that you read this information regarding the possible effects of electromagnetic interference (EMI) on your vehicle. Electromagnetic interference (EMI) refers to the effects that outside sources of electromagnetic energy (radio and television broadcasts, CB radios, garage door openers, etc.) might have on the control systems of your vehicle.
- Page 9 Rascal AutoGo Owner’s Manual Other types of hand-held devices like cellular telephones, laptop computers, AM/FM radios, and small appliances like hair dryers or electric shavers may also generate electromagnetic energy, but it is such a small amount that, as far as we know, no EMI problems should occur with these devices.
-
Page 10: Getting To Know Your Rascal Autogo
(see “Controls” on page 14). Serial Number — Each Rascal AutoGo is identified by a unique, 8-character Serial Number located on a label on the inside of the tiller, behind the Battery Pack. When you first get your vehicle, remove the Battery Pack and write down the vehicle’s Serial Number in the front of this manual (see page i) for future reference. -
Page 11: Illustration 1 - Rascal Autogo Components
Rascal AutoGo Owner’s Manual Illustration 1 — Rascal AutoGo Components EMC Part: 19286400 Rev.01 03/09/07... -
Page 12: Initial Set-Up
Battery Pack, installing/setting the dashboard clock, and charging the batteries. Unfolding The Rascal AutoGo is initially shipped in the flat fold configuration and must be unfolded for use. Unfold the Rascal AutoGo according to the following: • Raise tiller and dash to upright position •... -
Page 13: Charging Batteries
Rascal AutoGo Owner’s Manual Charging Batteries The Rascal AutoGo is equipped with two maintenance-free, airline approved, sealed 12V/15A batteries with an integral automatic battery charger mounted in a detachable Battery Pack installed onto the front of the tiller. Because your batteries may only have a partial charge when you first receive your vehicle, you may not experience full riding time until you have fully charged them. -
Page 14: Illustration 2 - Battery Charging
Rascal AutoGo Owner’s Manual Illustration 2 — Battery Charging EMC Part: 19286400 Rev.01 03/09/07... - Page 15 Charge the batteries as follows: 1. For your convenience, you can detach the Battery Pack from the Rascal AutoGo and move it to a 3-Prong Grounded Electrical Receptacle. If you choose, you can also park the Rascal AutoGo near a 3-Prong Grounded Electrical Receptacle without removing the Battery Pack.
-
Page 16: Installing The Battery Pack
Rascal AutoGo Owner’s Manual Installing the Battery Pack After the batteries have been fully charged, you’ll be ready to install the Battery Pack into the Tiller. Install the battery pack as follows (see Illustration 3). 1. Lift the Battery Pack by the handle and insert the bottom of the Battery Pack into the bottom of the Tiller. -
Page 17: Adjusting Tiller Position
Rascal AutoGo Owner’s Manual Adjusting Tiller Position For your riding comfort, the Rascal AutoGo tiller can be used in two positions. To adjust tiller position: • Lift Tiller Position Adjustment Knob to release tiller lock • Adjust tiller to preferred position •... -
Page 18: Installing & Setting The Dashboard Clock
Installing & Setting the Dashboard Clock Your Rascal AutoGo comes with a removable, battery-powered, quartz clock that mounts directly in the dash. This clock is packed separately to allow you to set it to your local time before installing in the dash. -
Page 19: Controls
Rascal AutoGo Owner’s Manual Controls The Rascal AutoGo includes the following controls (Illustration 5) used to operate the vehicle. Individual descriptions of each control are presented in pages 15-18. Illustration 5 — Controls EMC Part: 19286400 Rev.01 03/09/07... - Page 20 Battery Gauge (Fuel Gauge) should be lit when the key is in the “On” position. Use of a key to turn the Rascal AutoGo on and off also protects against unauthorized use of your Rascal AutoGo. Battery Power Save Feature...
- Page 21 Rascal AutoGo Owner’s Manual Dial-A-Speed Knob The Dial-A-Speed regulates the potential speed of the Rascal AutoGo. We strongly recommend setting it at 2 or 3 until you feel confident with controlling your vehicle properly. Turning the speed dial counter-clockwise decreases the top potential speed. Turning it clockwise (up to “10”) provides speed up to maximum potential speed.
- Page 22 Rascal AutoGo Owner’s Manual Battery Gauge (Fuel Gauge) The Rascal AutoGo includes an illuminated Battery Gauge that provides a visual indication of the electrical charge in the Battery Pack. It consists of 10 different LED bars (3 red, 4 amber and 3 green), that are lit in accordance with the state of battery charge.
- Page 23 Depress the switch button again to turn the headlight OFF. Clock For convenience, the dash of the Rascal AutoGo includes a battery-powered, analog clock displaying the current time of day. Instructions to set the time and install the clock are provided in the “Initial Set-up”...
-
Page 24: Operating The Rascal Autogo
This section presents instructions for getting on and off your vehicle, as well as driving it. It also details pushing it in freewheel mode and pulling it in freewheel mode. If you are unsure of how to operate your Rascal AutoGo vehicle, go back to the previous section before attempting any use. -
Page 25: Transferring On Or Off The Vehicle
Driving Once seated on your Rascal AutoGo vehicle, driving is as simple as using the Engager Lever to move forward or reverse and steering in the desired direction. Before driving the Rascal AutoGo vehicle, however, you should keep in mind the following recommendations. - Page 26 Rascal AutoGo Owner’s Manual 1. Tiller and dash are locked in position, facing the operator. 2. Frame Pivot Lock is engaged. 3. Seat is locked onto frame. Check latching lever. 4. Drivetrain is properly aligned and connected to frame. 5. Drivetrain clicks into position and locked.
-
Page 27: Speed Settings
Rascal AutoGo Owner’s Manual Speed Settings The overall forward/reverse speed range of the vehicle is selected from the Speed Control knob on the dash. Lower settings result in slower speeds. Higher settings provide faster speeds. When first operating your vehicle, select slower settings until you feel comfortable. -
Page 28: Curbs And Small Obstacles
1 inch (2.54 cm). Freewheel Operation The Rascal AutoGo features a “freewheel” mode to allow it to be pushed by hand (manual operation). To activate manually, turn the key switch OFF and locate the brake release lever under the rear cover on teh right side. -
Page 29: Automatic Folding And Unfolding
Automatic Folding and Unfolding A key feature of the Rascal AutoGo is the ability to automatically fold and unfold it for ease of transport, storage, and use. The benefit is one can fold their vehicle without any bending or lifting. Instructions to automatically fold and unfold the Rascal AutoGo are provided in this section. -
Page 30: Illustration 7 - Dash Release Lever
2. Pull Dash Release up and lift dash to upright position to engage wheel locks onto front wheels, see Illustration 7. 3. Position yourself on the right side of the Rascal AutoGo. Press the foot lever, as shown in Illustration 8, to retract the frame lock. - Page 31 Make sure the main frame is above the pivot lock and you are ready to automatically power fold the vehicle. 5. Pull the right side Engager lever to activate drive motor and initiate fold. The Rascal AutoGo will automatically fold under its own power and stop.
-
Page 32: Illustration 9 - Folding Operation
6. When fully folded, latch the frame and tiller together by pressing the tiller back against the main frame, see Illustration 9. 7. When folded, lower the dash to release the front wheel locks. 8. Using engager levers, you can operate the Rascal AutoGo forward/backward, as needed. EMC Part: 19286400 Rev.01 03/09/07... -
Page 33: Unfolding Information
Rascal AutoGo Owner’s Manual WARNING! When moving vehicle in power folded position, use extreme care to avoid tripping or colliding with yourself, others, or other vehicles. Unfolding Information Follow these instructions and refer back to illustrations 6-9 to unfold the vehicle using the power unfold feature:... -
Page 34: Flat Folding And Unfolding
Flat Folding and Unfolding As an added convenience, the Rascal AutoGo can be manually folded flat for storage or transport. When folded flat, the Rascal AutoGo can be easily stored in a car trunk, under your bed, or in a storage compartment. -
Page 35: Illustration 11 - Unfolding Flat Folded Vehicle
Rascal AutoGo Owner’s Manual To unfold the Rascal AutoGo after being folded flat: • Raise tiller and dash to upright position • Pull dash release lever and return dash to driving position • Raise seat frame and lock into position using the Seat Frame Cams •... -
Page 36: Disassembly & Re-Assembly
Disassembly & Re-Assembly In addition to easily folding and unfolding, the Rascal AutoGo can be quickly and easily disassembled for storage or transport, then re-assembled when needed. Instructions to take your Rascal AutoGo apart and put it back together are presented in this section. -
Page 37: Illustration 13 - Flattening Seat Frame
Rascal AutoGo Owner’s Manual 3. Lift Battery Pack handle up and pull forward to remove Battery Pack from tiller. 4. Flatten seat frame as shown in Illustration 13, by: — Rotating seat Frame Cams by pushing cam handles down until they lock, —... -
Page 38: Illustration 14 - Quick Release Drivetrain Lever
Rascal AutoGo Owner’s Manual 8. The Quick Release Drivetrain lever is located at the rear, underneath the frame. Push the red Quick Release Drivetrain Lever with your thumb, as shown in Figure 14. While the lever is pushed, lift rear of the scooter using the crossbar located in front of release lever. -
Page 39: Re-Assembling The Rascal Autogo
Rascal AutoGo Owner’s Manual Re-assembling the Rascal AutoGo Putting the Rascal AutoGo back together involves re-attaching the drivetrain, re-positioning the tiller and dash, raising & locking the seat frame, installing the seat, and installing the battery pack for driving operation. Instructions to re-assemble the Rascal AutoGo are provided in this section. - Page 40 Rascal AutoGo Owner’s Manual 3. Check brake lever is in the locked position (See page 23). Make sure the scooter cannot be moved with the ignition off. Fuel Gauge will flash on & off if Brake is in push mode and key is “On”.
-
Page 41: Transporting The Rascal Autogo
24 hours prior to departure through your travel agent or in person. Ask your airline or your travel agent whether they will need to disassemble the Rascal AutoGo or whether they plan to load and store it on the plane without disassembly. - Page 42 This vehicle does not meet Federal Safety Standards for motor vehicle seating. Do not sit, nor permit anyone else to sit, in the seat of the Rascal AutoGo during transportation in a motor vehicle as this poses a significant risk of bodily injury or even death.
-
Page 43: Maintenance
Your Rascal AutoGo requires only minimal maintenance and by setting time aside each month for careful inspection and checking items included in this section, you can be assured of a long, useful life of your Rascal AutoGo vehicle. Preventative Maintenance Performing periodic preventative maintenance on your Rascal AutoGo will ensure long, useful operational life as well as identifying any potential problems that may occur that might effect safe use and operation of the vehicle. -
Page 44: Headlight
Note: Headlight is a 24V 5W unit and is generally not available at local supply stores. Under normal operating conditions, the Rascal AutoGo requires no special Lubrication lubrication or grease. The drivetrain gearbox is a sealed unit. Bearings, joints, fasteners and other moving parts are protected by self-lubricating components so periodic lubrication is generally not necessary. -
Page 45: Tires
Tires Front and rear tires of the Rascal AutoGo are foam-filled and do not require air pressure. Tires should, however be checked periodically for damage, cuts, flat- spots, or excessive tread wear. Damaged tires should be replaced. -
Page 46: Polishing
Rascal AutoGo Owner’s Manual Polishing Polish all plastic components to help protect them from scratches and a dull finish. This can be done by using a non-abrasive auto polishing material available at your local automotive parts dealer or local department store (automotive section). -
Page 47: Illustration 17- Cable Turnbuckle Adjustment
Rascal AutoGo Owner’s Manual Illustration 17 — Cable Turnbuckle Adjustment EMC Part: 19286400 Rev.01 03/09/07... -
Page 48: Drivetrain
Rascal AutoGo Owner’s Manual Drivetrain The parking brake of the drivetrain includes an adjustment setscrew for the brake pad. If brake starts to squeal, tighten setscrew. Brake nut should be set 1/6" (1.5 mm) from brake pad. Periodically clean dirt in brake pad by blowing dirt out with air pressure hose. -
Page 49: Replacing Clock Battery
Rascal AutoGo Owner’s Manual Replacing Clock Battery After time, the dash clock may begin to lose time, or stop, when the battery runs down. The battery is easily replaced by removing the clock from the dash, prying open the clock’s case, and inserting a new battery. Battery location is shown in Illustration 18. - Page 50 Rascal AutoGo Owner’s Manual Battery Types: SR626SW, UCC 377, Ray-O-Vac RW329 1. Remove clock from the dash by gently prying the edge of the clock from the dash. 2. Use a small screwdriver to open the case by inserting the screwdriver blade into the notch on the back cover.
-
Page 51: Troubleshooting Guide
Rascal AutoGo Owner’s Manual Troubleshooting Guide This table is only a guide to aid you in getting your vehicle operating, should you have any problems. If you are unable to get your vehicle operating, call either Electric Mobility Customer Service toll free number located at the front of this manual or your local Authorized Service Center. - Page 52 Rascal AutoGo Owner’s Manual temperature and then fully recharge 4. Defective charger 4. Contact Electric Mobility or your Authorized Service Center Erratic behavior when engager operated 1. Faulty engager 1. Contact Electric Mobility or your Authorized Service Center 2. Defective wiring harness 2.
-
Page 53: Controller Fault Codes
Controller Fault Codes In addition to the troubleshooting information in the previous section, the controller used in the Rascal AutoGo provides diagnostic information through means of a Fault Code Display that appears on the Battery Gauge. When a fault is detected, selected segments of the Battery Gauge will light to indicate the faults. -
Page 54: Parts Ordering Procedures
Rascal AutoGo Owner’s Manual Parts Ordering Procedures To help us serve you as quickly as possible have your phone number, vehicle serial number or your order number ready when you call. When ordering parts, please have your method of payment ready (i.e., credit card number and expiration date, check, etc.). -
Page 55: Accessories
Rascal AutoGo Owner’s Manual Accessories Your Rascal AutoGo can include several useful accessories to make your riding experience more enjoyable, convenient, and easier. These accessories can include: • Electric Trunk Lift • Trunk Lift Bracket • AutoRack - Vehicle Carrier •... -
Page 56: Specifications
Rascal AutoGo Owner’s Manual Specifications Electrical: Dimensions: Batteries Two: 12V/15Ah Length 41-42” (104-106 cm) Battery Charger Width 21” (53.3 cm) Charger Cord Length 3’ (91.4 cm) Height 37” (94 cm) Controller Digital with programmable slow mode Folded, Vertical 38” (96.5 cm) H x 21” (53.3 cm) W x 22” (55.8 cm) L Folded, Horiz., w/Seat... -
Page 57: Warranty
Warranty The Rascal Company, warrants the vehicle, other than its component battery or batteries, to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase. If, within such warranty period, any such product shall be proven to The Rascal Company, satisfaction to be defective, such product shall, at option, be repaired or replaced. - Page 58 Rascal AutoGo Owner’s Manual EMC Part: 19286400 Rev.01 03/09/07...
- Page 59 Rascal AutoGo Owner’s Manual EMC Part: 19286400 Rev.01 03/09/07...
Need help?
Do you have a question about the Rascal AutoGo and is the answer not in the manual?
Questions and answers
is there a way to test my rascal autogo onboard battery charger?
To test the onboard battery charger of a Rascal AutoGo, follow these steps:
1. Check the Battery Pack LED – Ensure the LED on the Battery Pack is lit when plugged in.
2. Verify Cord Connections – Make sure the power cord is properly plugged into both the Battery Pack and the electrical outlet.
3. Observe Charging Behavior – If the battery does not charge, load test the batteries to determine if they need replacement.
4. Check for a Faulty Charger – If the Battery Pack LED is not lit and connections are correct, the charger may be defective. Contact Electric Mobility or an Authorized Service Center for further assistance.
This answer is automatically generated