Dell PowerEdge 850 Installation And Troubleshooting Manual page 17

Diskette read failure
Diskette subsystem reset failed
Drive not ready
Dual rank DIMMs are not supported in the
following memory sockets in this memory
configuration.
Error: Incorrect memory configuration.
Ensure memory in slots DIMM1_A and
DIMM1_B, DIMM2_A and DIMM2_B match
identically in size, speed, and rank.
Error: Remote Access Card initialization
failure.
Error 8602: Auxiliary device failure.
Verify that the keyboard and mouse are
securely attached to correct connectors.
Gate A20 failure
General failure
IDE Primary drive 1 not found
Keyboard controller failure
Keyboard data line failure
Keyboard failure
Keyboard stuck key failure
Keyboard fuse has failed.
Manufacturing mode detected
Memory address line failure at address,
read value expecting value
Memory double word logic failure at
address, read value expecting value
Memory odd/even logic failure at start
address to end address
Memory write/read failure at address,
read value expecting value
Memory tests terminated by keystroke
No boot device available
No boot sector on hard-disk drive
No timer tick interrupt
Not a boot diskette
PCI BIOS failed to install
PCIe Degraded Link Width Error: Embedded
Bus#nn/Dev#nn/Funcn
Expected Link Width is n
or optical drive interface "Troubleshooting an Optical
cable, or loose power cable.
Faulty or improperly inserted Replace the diskette.
diskette.
Faulty diskette drive or Ensure that the diskette drive and optical drive cables are properly connected.
optical drive controller. See
in "Troubleshooting Your System." If the problem persists, see
Diskette missing or Reinsert or replace the diskette.
improperly inserted in
diskette drive.
Invalid memory configuration. Correct the memory configuration. See
Guidelines" in "Installing System Components."
An unmatched pair of memory Install a matched pair of memory modules, or remove the memory module in
modules is installed. socket DIMM1_B. See
"Installing System Components."
Faulty or improperly installed Ensure that the RAC is properly installed. See
RAC. Cards" in "Troubleshooting Your System," or
"Installing System Components."
Loose or improperly Replace the mouse. If the problem persists, replace the keyboard.
connected mouse or
keyboard cable; faulty mouse
or keyboard.
Faulty keyboard controller See
(faulty system board).
Operating system corrupted Reinstall the operating system.
or improperly installed.
Improperly connected or Ensure that the drive cables are properly connected. See
missing optical drive or tape Your
backup unit.
If no drive is installed, disable the IDE controller. See "Using the System Setup
Program" in your User's Guide.
Faulty keyboard controller See
(faulty system board).
Loose or improperly Ensure that the keyboard is properly connected. If the problem persists,
connected keyboard cable; replace the keyboard. If the problem persists, see
faulty keyboard; faulty
keyboard controller.
Keyboard fuse has failed. Replace the keyboard.
Faulty system board. See
System is incorrectly After the message appears during system boot, press <Alt><F> to turn off
configured. manufacturing mode.
Faulty or improperly installed Ensure that all memory modules are properly installed. See
memory modules, or faulty System
system board. "Getting
The spacebar was pressed Information only.
during POST to terminate the
memory test.
Faulty or missing diskette Check the Integrated Devices configuration settings in the System Setup
drive, optical drive, or hard program. See "Using the System Setup Program" in your User's Guide. Ensure
drive. that either SATA Controller, Diskette Controller, or IDE Controller is enabled.
If the system is booting from a SCSI controller, ensure that the controller is
properly connected. If the problem persists, replace the drive. See
Drives."
An operating system is not Check the hard-drive configuration settings in the System Setup program. See
on the hard drive. "Using the System Setup Program" in your User's Guide.
Faulty system board. See
Not a bootable diskette. Use a bootable diskette.
Loose cables to expansion Ensure that all appropriate cables are securely connected to the expansion
card(s); faulty or improperly cards. See
installed expansion card. System."
Faulty or improperly installed Reseat the PCIe cards. See
PCIe card. "Getting
Drive" in "Troubleshooting Your System."
"Troubleshooting a Diskette Drive" and
"General Memory Module Installation
"Getting Help."
System" for the appropriate drive installed in your system.
"Getting Help"
"Getting Help."
Memory" in "Troubleshooting Your System." If the problem persists, see
Help."
"Getting Help."
"Troubleshooting Expansion
"Expansion
Help."
"Troubleshooting an Optical Drive"
"Getting Help."
"General Memory Module Installation
Guidelines" in
"Troubleshooting Expansion
"Installing a RAC Card" in
"Troubleshooting
"Getting Help."
"Troubleshooting
"Installing
Cards" in "Troubleshooting Your
Cards." If the problem persists, see