Touchpad Programming - Regency 4720 Installation Manual

Regency ® Model 4720 Control/Communicator Installation Manual (P/N 150476, Rev. A)

Touchpad Programming

19
All options can be addressed in Hex format. Hex programming is not recommended, except as a handy
troubleshooting tool. To obtain a Hex programming form, contact ITI Order Entry at 1-800-777-4841.
Note: Touchpad programming can only be accomplished through the use of a full-function touchpad with an LCD.
During programming, the system will not respond to alarms.
The following procedure shows how to set up the system for downloading using the 4-TEST method (see Section
18.1.2).
1. Apply power to the Model 4720. The system will power up in the Set Time mode.
2. Press MUTE, MUTE. You are now in the Normal Operating mode.
3. Press 6, TEST, followed by Code 0. Code 0 is factory set to "1-2-3-4-5-6". This will place the Model 4720
into the Hex Programming mode. The display will indicate that you are at address $000.
4. Press CHM, 6, 0, TEST. This step takes you to address $060, the display will show $060:$XX.
At this point you will start entering the computer phone #. Each address location $060 through $067 can hold
two (2) digits of the phone number. You must fill all of the address locations. If your phone number does not
use all of the address locations, enter "FF" in the unused locations. To enter "FF" press BYPS, 6, BYPS, 6.
The example below shows how you would enter the phone number 555-1212.
Example:
Display = $060:$–– ––, press 5, 5, TEST.
Display = $061:$–– ––, press 5, 1, TEST.
Display = $062:$–– ––, press 2, 1, TEST.
Display = $063:$–– ––, press 2, BYPS, 6, TEST.
Display = $064:$–– ––, press BYPS, 6, BYPS, 6, TEST.
Display = $065:$–– ––, press BYPS, 6, BYPS, 6, TEST.
Display = $066:$–– ––, press BYPS, 6, BYPS, 6, TEST.
Display = $067:$–– ––, press BYPS, 6, BYPS, 6, TEST.
5. At this point the display will show $068:$XX. Press STAT, CLR, 7. The display will show
$068:$–––––––7. Press TEST. This step selects the Up/Down Report Enable.
6. Press CHM, 6, BYPS, 6, TEST, STAT, CLR. The display will show $06F:$––––––––. Press 4 if you are
using Touch-Tone dialing on Line 1 (5 for Touch-Tone on Line 2), then press TEST. If you are NOT using
Touch-Tone dialing, just press TEST.
7. Press CHM, BYPS, 1, 8, TEST. The display will show $0A8:$XX. For locations $0A8 through $0AA, you
must enter the account # that has been programmed into the downloading computer. Each address location can
hold two (2) digits of the account number. If the account number is not six (6) digits long, you must enter
leading zeros. The example below shows how to enter an account # of 1234.
Example:
Display = $0A8:$–– ––, press 0, 0, TEST.
Display = $0A9:$–– ––, press 1, 2, TEST.
Display = $0AA:$–– ––, press 3, 4, TEST.
8. After entering the account #, press MUTE, MUTE to exit Hex Programming mode.
9. Press 4 TEST, followed by Code 0 to begin the downloading process. The display will indicate that the Model
4720 is downloading. After about four (4) minutes the display will show READY. The 4720 has now been
programmed by the downloading computer.
WARNING:
69
Revised 10/98