Installation Warnings; Installation Instructions - Electrolux EQBL100AS User Manual

Integrated barbecue
Hide thumbs Also See for EQBL100AS:
Table of Contents

Advertisement

6 installation warnings/installation instructions electrolux integrated barbecue

Installation warnings

warning
• T his appliance shall only be used in an above ground,
open air situation with natural ventilation without
stagnant areas, where gas leakage and product of
combustion are rapidly dispersed by wind or natural
convection. This barbecue has been designed for
outdoor use only. Refer to diagrams below.
• N ever install this barbecue inside any building, garage,
shed or breezeway or inside a boat, caravan or
recreational vehicle. This is to prevent the possibility of
fire or carbon monoxide poisoning or asphyxiation.
• A ny enclosure in which this appliance is installed shall
comply with one of the following:
– An enclosure with walls on all sides, but at least
one permanent opening at the ground level and no
overhead covering.
– Within a partial enclosure that includes an overhead
cover and no more than 2 walls.
– Within a partial enclosure that includes an overhead
cover and more than 2 walls, the following shall apply:
– at least 25% of the total wall area is completely
open and at least 30% of the remaining wall area
is open and unrestricted
• I n the case of balconies, at least 20% of the total of
the side, back and front wall areas shall be and remain
open and unrestricted.
Outdoor area example 1
Outdoor area example 2
Outdoor area example 3
both ends
open
Outdoor area example 4
Outdoor area example 5
open side at
30% or more
least 25% of
in total of the
total wall area
remaining wall
area is open and
unrestricted
open side at
30% or more
least 25% of
in total of the
total wall area
remaining wall
area is open and
unrestricted

Installation instructions

Choosing a location
• T his appliance must not be installed on any combustible
material. A minimum clearance from any combustible
materials is 450mm (18").
• T he vertical clearance above the cooking surface to any
combustible materials must be at least 600mm.
• T his appliance must be installed accordance with
Australian Standards AS 4557 and AS 5601 and in
accordance with local authority.
• W hen using LPG in an enclosure ventilation must be
provided. Gas is highly explosive and can cause serious
injury and damage to property if allowed to accumulate
and then be ignited.
• T his barbecue is intended to be built into a bench top
with a minimum depth of 600 mm.
• A void windy positions as this will affect cooking
performance and burner efficiency. If this situation
cannot be avoided some shielding may be necessary.
The mounting enclosure
• T he barbecue requires a non-combustible barrier under
the barbecue to prevent excessive temperatures being
accessed. The barrier panel is to be placed 30mm
under the base of unit. There are spacers added to
bottom of unit to prevent barrier panel being too close
to barbecue base. Refer to diagram on next page.
• T he mounting enclosure must be constructed from
non-combustible materials. Suitable materials for
construction include masonry, granite, marble,
Hardiplank
, Villaboard
®
• T his appliance requires venting in the front wall of the
enclosure. See diagram below for details.
• T his appliance can be mounted either in an island type
bench or a bench with a splashback. Please read the
specific requirements for each mounting situation.
Island style installation
• I f this appliance is installed in an island mount, it can be
centrally positioned. Special attention should be given
to the overall size of the island top to consider the hood
open and the overhang. Please see below.
• T he cut-out size required is 1025mm x 502mm (see
diagram).
warning
• T his appliance requires venting. An open area as
indicated below must be allowed for. A suitable grille can
be fitted if desired. This vent area is to allow air into the
enclosure for the correct combustion of gases and for
the correct exhausting of the products of combustion. In
the case of LPG the gas is heavier than air, this vent in
the situation where there may be a leak allows the gas to
escape from the enclosure. This vent must be
700mm x 25mm minimum and positioned centrally
135mm below the mounting surface. (see diagram).
Installing in a bench with a splashback
• T he splashback must be made from a non-combustible
material.
• I n the case of mounting this appliance against a wall
or fence it is imperative that care be taken to ensure
the isolation of combustible materials. All combustible
materials must be kept 450mm away from the
barbecue.
over a metal frame or tiles.
®

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Eqbh100as

Table of Contents