Page 1 Netra ™ AC200 and DC200 Server User’s Guide Sun Microsystems, Inc. 901 San Antonio Road Palo Alto, CA 94303 U.S.A. 650-960-1300 Part No. 806-5978-11 August 2001, Revision A Send comments about this document to: docfeedback@sun.com...
Page 2 Sun, Sun Microsystems, the Sun logo, AnswerBook2, docs.sun.com, Solaris, Sun Enterprise, OpenBoot, SunSolve, and Netra are trademarks, registered trademarks, or service marks of Sun Microsystems, Inc. in the U.S. and other countries. All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International, Inc. in the U.S. and other countries. Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems, Inc.
Page 3: Table Of Contents
Contents Part I Installation and Configuration Introduction 1-1 Overview of the Netra T1 Server 1-2 Contents of the Ship Kit 1-3 Optional Hardware and Software 1-5 Front Panel 1-6 Back Panel 1-7 The Fans Inside the Netra T1 Server 1-8 Tools You Need for Installation 1-8 Environmental Specifications 1-9 1.8.1...
Page 4 Tips for Using a Sun StorEdge 72-inch Rack 5-11 Installing Into a Two-Post Relay Rack 5-12 5.2.1 The Fixed Mounting Bracket Kit 5-12 5.2.2 Attaching the Fixed Mounting Brackets 5-12 Connecting the Cables 6-1 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 5 Connecting the Cables to the Server 6-2 Using a Single DC Power Cord 6-4 Setting Up Serial Connections 6-4 6.3.1 Connecting to a Terminal Server 6-6 6.3.2 Using a DB-25 Adapter for Your Serial Link 6-8 6.3.3 Using a DB-9 Adapter for Your Serial Link 6-9 6.3.4 Settings for the Serial Connections 6-10 Connecting to the Netra T1 Server From a Laptop Running Microsoft...
Page 6 Dedicating Serial A/LOM to the LOMlite2 8-19 8.6.2 Sharing Serial A/LOM Between the LOMlite2 and the Console 8- Viewing the Event Reports That the LOMlite2 Sends to syslogd 8-20 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 7 The LOMlite2 Shell Command List 8-21 Checking the Status of the Server’s Fans 8-24 Managing the Netra T1 Server From the Solaris Prompt 9-1 Monitoring the System From Solaris 9-2 9.1.1 Viewing Online LOMlite2 Documentation 9-2 9.1.2 Checking the Power Supply Unit (lom -p) 9-2 9.1.3 Checking the Fans (lom -f) 9-3 9.1.4...
Page 8 Replacing Fan 3 (CPU Fan) 11-19 Part IV Appendixes A. Configuring the LOMlite2 Device Driver A-1 The LOMlite2 Device Driver A-2 Configuring the LOMlite2 Device Driver A-3 B. System Board Jumper Settings B-1 viii Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 9 Index 1 Contents...
Page 10 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 11 The Netra T1 Server 1-2 FIGURE 1-1 Contents of the Ship Kit 1-4 FIGURE 1-2 The Front Panel of the Netra T1 AC200 and DC200 Servers 1-6 FIGURE 1-3 The Back Panel of the Netra T1 AC200 Server 1-7 FIGURE 1-4...
Page 12 Netra T1 AC200 Server Power (On/Standby) Switch 7-8 FIGURE 7-2 The Location of the Lights-Out Management Device on the System Board 8-2 FIGURE 8-1 Sample Output From the environment Command 8-9 FIGURE 8-2 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 13 Sample LOMlite2 Device Event Log (Oldest Event Reported First) 8-10 FIGURE 8-3 Locations of Fans 1, 2, 3, and 4 8-24 FIGURE 8-4 Sample LOMlite2 Device Event Log (Oldest Event Reported First) 9-7 FIGURE 9-1 Front Panel Power and Fault LEDs 10-5 FIGURE 10-1 Back Panel Ethernet Link, Fault and Power LEDs 10-5...
Page 14 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 15 Crossovers Inside the 25x9-way D-type Female-to-Female Adapter 6-11 TABLE 6-5 Boot Modes 8-7 TABLE 8-1 LOM Commands 8-21 TABLE 8-2 FRUs Available for the Netra T1 AC200 and DC200 Servers 11-4 TABLE 11-1 LOM Configuration File Parameters A-3 TABLE A-1 Factory-Default Jumper Settings B-2 TABLE B-1...
Page 16 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 17: How This Book Is Organized
Preface The Netra T1 AC200 and DC200 Server User’s Guide describes how to install, manage, and maintain the Netra T1 AC200 and DC200 servers. The manual is intended for system administrators who have experience in setting up networked Solaris servers.
Page 18 See one or more of the following for this information: AnswerBook2™ online documentation for the Solaris software environment Other software documentation that you received with your system xviii Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 19: Typographic Conventions
Typographic Conventions Typeface Meaning Examples The names of commands, files, Edit your .login file. AaBbCc123 and directories; on-screen Use ls -a to list all files. computer output % You have mail. What you type, when AaBbCc123 contrasted with on-screen Password: computer output AaBbCc123 Book titles, new words or...
Page 20: Related Documentation
Sun is interested in improving its documentation and welcomes your comments and suggestions. You can email your comments to Sun at: docfeedback@sun.com Please include the part number (806-5978-11) of your document in the subject line of your email. xx Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 21: Safety Precautions
Safety Precautions For your protection, observe the following safety precautions when setting up your equipment: Follow all cautions and instructions marked on the equipment. Never push objects of any kind through openings in the equipment. Dangerous voltages may be present. Conductive foreign objects can produce a short circuit that could cause fire, electric shock, or damage to your equipment.
Page 22 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 23: Part I Installation And Configuration
Installation and Configuration PA RT...
Page 25: Introduction
C H A P T E R Introduction This chapter lists the features of the Netra T1 AC200 and DC200 servers, the contents of the ship kit, and the optional hardware and software that is available for them. It also describes the front and back panels, lists the tools you will need to use to install a server, and describes the servers’...
Page 26: Overview Of The Netra T1 Server
Solaris servers. The Netra T1 AC200 server is powered by an AC supply. The Netra T1 DC200 server is powered by –48 VDC/–60 VDC supplies. This is the only difference between the two models.
Page 27: Contents Of The Ship Kit
10-32 UNF Sun rackmounting screw kit 565-1645-01 Side-mounting bracket screw kit 565-1654-01 Netra T1 AC200 and DC200 Server User’s Guide 806-5978-10 Netra T1 AC200 and DC200 Server Safety and Compliance Guide 806-6135-10 Netra T1 AC200 and DC200 Server Product Notes 806-6134-1x Chapter 1 Introduction...
Page 28: Figure 1-2 Contents Of The Ship Kit
Contents of the Ship Kit FIGURE 1-2 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 29: Optional Hardware And Software
Netra T1 server. To order them, contact your local Sun sales representative. Note – The 256- and 512-Mbyte DIMMs available for use in the Netra T1 AC200 and DC200 servers cannot be used in Netra t1 Model 100 or 105 servers.
Page 30: Front Panel
Gigabit Ethernet and FC-AL PCI Adapter X2069A Front Panel Power LED Fault LED CD-ROM drive bay The Front Panel of the Netra T1 AC200 and DC200 Servers FIGURE 1-3 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 31: Back Panel
The Back Panel of the Netra T1 AC200 Server FIGURE 1-4 shows the components on the Netra T1 DC200 server’s back panel. Except FIGURE 1-5 for the power inlet, they are identical to those on the Netra T1 AC200. Power (On/Standby) switch Ethernet DC power...
Page 32: The Fans Inside The Netra T1 Server
Lights-Out Management (LOM) commands to check their status. Note – The arrangement of the components inside the Netra T1 AC200 and DC200 servers is not the same as it was inside the Netra t1 Model 100 and 105 servers. The fans are also numbered and positioned differently.
Page 33: Environmental Specifications
Environmental Specifications 1.8.1 Tolerance of Environmental Conditions You can operate and store the system safely in the following conditions: Ambient temperature Operating: 5˚C to 40˚C (temporary operation outside these limits is permitted for a maximum of 96 hours within the range –5˚C to 55˚C) Storage: –40˚C to 70˚C Relative humidity Operating: 5% to 85% (non-condensing)
Page 34: Choosing Between A Rack And A Cabinet
Cabinets often require cables to be run under the floor. What’s Next? When you have read this chapter, go to Chapter 2 to find out how to estimate the power and cooling requirements for your server. 1-10 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 35: Power And Cooling
Power and Cooling This chapter contains information about the power consumption of the Netra T1 AC200 and DC200 servers. It also tells you how to estimate the amount of heat that your cooling system must dissipate. The chapter contains the following sections: Section 2.1, “Operating Power Limits and Ranges”...
Page 36: Operating Power Limits And Ranges
However, these figures represent “worst-case” scenarios. They are unlikely to be observed in a real installation. Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 37: Power Consumption
Power Consumption for the Available Configurations of the Netra T1 Server TABLE 2-2 Netra T1 Hardware Options Power Consumption Power Consumption Model Installed (Nominal) (Maximum) AC200 1x18 GB hard disk 95 VA 1x256 MB DIMM AC200 1x18 GB hard disk 100 VA 2x256 MB DIMM AC200 2x18 GB hard disk...
Page 38: Estimating Heat Dissipation
A general formula for doing this is to multiply the figure for the power consumption by 3.415. For example, the heat that must be dissipated for a Netra T1 AC200 server containing a single hard disk drive and a single 256-MB DIMM is: 70 W x 3.415 = 240 BTU/hr...
Page 39: Using Dc Power
This chapter applies only to the Netra T1 DC200 server. If you have purchased a Netra T1 AC200 server, skip this chapter and go to Chapter 4. This chapter provides information on grounding a Netra T1 DC200 server and on assembling the DC power connectors.
Page 40: Grounding The Netra T1 Dc200 Server
Note – For more information about grounding the server, refer to the Netra T1 AC200 and DC200 Safety and Compliance Guide. Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 41: Assembling The Dc Power Connectors
Assembling the DC Power Connectors 3.2.1 The Insulated Conductors You Need to Use The insulated conductors you use must have the following characteristics: Material: tinned copper (multistranded) Size: 12 AWG (2.5 mm ) (maximum) Rating: 300 vrms (minimum) Low-smoke fume (LSF) Fire resistance: VW-1 GR63-CORE compliant...
Page 42: Figure 3-2 Stripping The Insulation From The Wire
DC connector where you want to insert the first wire, and pressing down on the screwdriver (see FIGURE 3-4 Opening the DC Connector Cage Clamp (Lever Method) FIGURE 3-3 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 43: Figure 3-4 Opening The Dc Connector Cage Clamp (Screwdriver Method)
Top of connector Opening the DC Connector Cage Clamp (Screwdriver Method) FIGURE 3-4 7. Feed the exposed section of the appropriate wire into that hole in the DC connector. shows which wires should be inserted into each hole in the DC connector. FIGURE 3-5 Top of connector –48V Return...
Page 44: Installing The Strain Relief Housings
2. Route the three wires coming from the DC power source through the opening at the end of the bottom portion of the strain relief housing (see FIGURE 3-7 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 45: Figure 3-7 Routing The Wires Out Of The Strain Relief Housing
Routing the Wires Out of the Strain Relief Housing FIGURE 3-7 3. Insert the tie wrap into the bottom portion of the strain relief housing (see FIGURE 3-8 Securing the Wires to the Strain Relief Housing FIGURE 3-8 4. Loop the tie wrap over the wires and back out of the strain relief housing and tighten the tie wrap to secure the wires to the strain relief housing (see FIGURE 3-8 5.
Page 46: Figure 3-9 Assembling The Strain Relief Housing
(see Chapter 7) until you have installed any optional hardware components you need (see Chapter 4) and until you have installed the server securely into a rack or cabinet (see Chapter 5). Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 47: Installing Optional Hardware Components
C H A P T E R Installing Optional Hardware Components If you do not want to install any optional hardware components, skip this chapter and go straight to Chapter 5, which tells you how to install the Netra T1 server into a rack.
Page 48: Installing And Removing Hot-Pluggable Hard Disk Drives
(see ). This causes the metal lever to open. FIGURE 4-1 Holding the latch, pull the disk drive out of its bay. 4. Replace the grilles and front bezel. Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 49: Figure 4-1 Inserting And Removing Hard Disks
Inserting and Removing Hard Disks FIGURE 4-1 Chapter 4 Installing Optional Hardware Components...
Page 50: Opening The Netra T1 Server
ESD pad Using the Antistatic Wrist Strap Supplied With the Server FIGURE 4-2 1. Begin the procedure based on the status of your server: Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 51: Figure 4-3 Removing The Top Cover
If your server is new and you have just removed it from its packaging, go straight to Step 3. If your server is currently in use, but you need to open it to install or replace a hardware component, then: a.
Page 52: Identifying Server Components
9. PCI card slide support rail 10. DIMM 11. Power Supply Unit 12. Fans 1 and 2 13. Fan 3 (CPU) 14. Fan 4 Components of the Netra T1 Server FIGURE 4-4 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 53: Installing And Removing A Cd-Rom Drive
Installing and Removing a CD-ROM Drive Class 1 Laser Product Luokan 1 Laserlaite Klasse 1 Laser Apparat Laser Klasse 1 Caution – Follow the instructions in this section carefully. The CD-ROM drive contains a laser device. Do not attempt to open the CD-ROM drive’s enclosure and do not attempt to install or remove a CD-ROM drive using any procedures other than the ones contained in this section.
Page 54: Figure 4-5 Installing An Internal Cd-Rom Drive
6. Replace the server’s cover and tighten the captive screw (see FIGURE 4-9 Section 4.7, “Replacing the Server’s Top Cover” on page 4-15). 7. Replace the front bezel. Paddleboard Catch Installing an Internal CD-ROM Drive FIGURE 4-5 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 55: Removing A Cd-Rom Drive
4.4.2 Removing a CD-ROM Drive 1. Remove the top cover by following the procedure described in Section 4.2, “Opening the Netra T1 Server” on page 4-4. Make sure you disconnect all power cables and wear an antistatic wrist strap. 1. Remove the front bezel. Release it from the server by pressing in on the tabs at either end of the bezel.
Page 56: Figure 4-6 Installing Memory Into A Socket On The System Board
Note – There are four DIMM slots. The one nearest to the CPU fan is slot 0. The one nearest to the power supply unit is slot 3. Put the first DIMM in slot 0, and install subsequent DIMMs in contiguous slots. 4-10 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 57: Installing And Removing A Pci Card
Installing and Removing a PCI Card 4.6.1 Installing a PCI Card For a list of the PCI cards available from your local Sun Sales representative, see Chapter 11. Note – If you are installing a full-length PCI card and you also want to install a CD-ROM drive, install the CD-ROM drive first (see Section 4.4, “Installing and Removing a CD-ROM Drive”...
Page 58: Figure 4-7 The Rotating Retention Bracket And The Position Of A Pci Card
Metal PCI connector PCI card slide retainer The Rotating Retention Bracket and the Position of a PCI Card FIGURE 4-7 4-12 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 59: Figure 4-8 Using The Pci Card Retainer, Slide Support Rail, And Plastic Bracket
6. Slide the PCI card retainer into a position at the back of the PCI card to prevent excessive flexing of the board (see FIGURE 4-8 If you are installing a full-length PCI card, insert the end of the card into the groove in the plastic bracket shown in ;...
Page 60: Removing A Pci Card
(see FIGURE 4-7 7. Replace the server cover and tighten the captive screw (see FIGURE 4-9 Section 4.7, “Replacing the Server’s Top Cover” on page 4-15). 4-14 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 61: Replacing The Server's Top Cover
Replacing the Server’s Top Cover When you have finished installing an option module, replace the top cover, making sure the alignment arrows on the lid and chassis line up. Then tighten the captive retaining screw at the rear (see FIGURE 4-9 Alignment arrows Replacing the Top Cover FIGURE 4-9...
Page 62 4-16 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 63: Installing The Server Into A Rack
C H A P T E R Installing the Server Into a Rack This chapter tells you how to install a Netra T1 server into a rack. The chapter contains the following sections: Section 5.1, “Installing Into a 19-Inch Four-Post Rack” on page 5-2 Section 5.2, “Installing Into a Two-Post Relay Rack”...
Page 64: Installing Into A 19-Inch Four-Post Rack
M4 nuts 240-1373 Rack screw kit 565-1645 A bracket is provided to aid cable management at the back of the server (see FIGURE 5-1 Cable Management Bracket FIGURE 5-1 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 65: Assembling The Slides And Mounting The Server
5.1.2 Assembling the Slides and Mounting the Server 1. Position the two parts of the slide so that the double-angled ear (A) is in the correct position for the rack you are installing into. For the Sun StorEdge 72-inch tall (19-inch wide) rack, the double-angled ear (A) must be to the rear (see FIGURE 5-2 For a standard 19-inch wide rack, the double-angled ear (A) must be to the front...
Page 66 For a standard 19-inch rack, refer to . Leave the screws slightly loose to FIGURE 5-6 allow adjustment when you slide the server into the rack. Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 67: Figure 5-4 Fastening The Slide Mounts To A Sun Storedge 72-Inch Tall Rack - Rear View (Side Panels Removed For Clarity)
Fastening the Slide Mounts to a Sun StorEdge 72-inch Tall Rack – Rear View FIGURE 5-4 (Side Panels Removed for Clarity) Chapter 5 Installing the Server Into a Rack...
Page 68: Figure 5-5 Fastening The Slide Mounts To A Sun Storedge 72-Inch Expansion Rack - Front View (Side Panels Removed For Clarity)
Fastening the Slide Mounts to a Sun StorEdge 72-inch Expansion Rack – Front FIGURE 5-5 View (Side Panels Removed for Clarity) Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 69: Figure 5-6 Fastening The Slide Mounts To A Standard 19-Inch Rack
Fastening the Slide Mounts to a Standard 19-inch Rack FIGURE 5-6 7. Slide the Netra T1 server into the rack (see FIGURE 5-7 Chapter 5 Installing the Server Into a Rack...
Page 70: Figure 5-7 Sliding The Netra T1 Server Into A Standard 19-Inch Rack
Sliding the Netra T1 Server Into a Standard 19-Inch Rack FIGURE 5-7 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 71: Figure 5-8 Adjusting The Slide Mounts And Screwing The Server Into The Rack
8. Align the thumbscrews on the sides of the server with the slide mounts in the rack (see FIGURE 5-8 If necessary, readjust the slide mounts to align the server properly. The thumbscrews need to be finger-tight. Adjusting the Slide Mounts and Screwing the Server Into the Rack FIGURE 5-8 9.
Page 72: Fitting The Cable Management Bracket
You can use the loops in the bracket to secure the cables with cable ties. Cable management bracket Fitting the Cable Management Bracket to a Sun StorEdge or a Standard 19- FIGURE 5-9 Inch Rack 5-10 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 73: Tips For Using A Sun Storedge 72-Inch Rack
5.1.4 Tips for Using a Sun StorEdge 72-inch Rack For maximum stability, fill the rack from the bottom up and leave at least 4U of space free at the top. To prevent warm air flowing to the front of the rack and being recirculated (which would reduce the efficiency of your cooling system and potentially cause overheating), close off the empty spaces at the top of the rack with filler panels.
Page 74: Installing Into A Two-Post Relay Rack
5.2.2 Attaching the Fixed Mounting Brackets 1. Remove the thumbscrew rack mounting brackets from either side of the server (see FIGURE 5-10 Removing the Thumbscrew Brackets FIGURE 5-10 5-12 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 75: Figure 5-11 Fitting The Fixed Mounting Brackets
2. Remove the first, third and fourth fixing screws from the plastic slide-mounts on the sides of the unit (see FIGURE 5-11 3. Fit the two front fixed brackets to the rearmost two of the three tapped holes towards the front of the server. Use the Phillips-head countersunk screws provided.
Page 76: Figure 5-12 The Netra T1 Server Installed In A Two-Post Rack
What’s Next? When you have installed the Netra T1 server into the rack, go to Chapter 6 for information about connecting the cables and setting up serial connections. 5-14 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 77: Connecting The Cables
C H A P T E R Connecting the Cables This chapter describes how to connect the power cables and the Ethernet and serial cables to the Netra T1 server. It also tells you how to set up the serial connections you need.
Page 78: Connecting The Cables To The Server
Connecting the Cables to the Netra T1 AC200 Server FIGURE 6-1 SCSI adapter Serial DC power links cable Ethernet links DB-25 adapter Connecting the Cables to the Netra T1 DC200 Server FIGURE 6-2 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 79 Before following the instructions in this section, make sure you have installed the Netra T1 server into a rack or cabinet (see Chapter 5). 1. Connect the power cord or cords. 2. Connect the server to at least one Ethernet hub. You can connect to a maximum of two Ethernet hubs (unless you have a PCI adapter installed).
Page 80: Using A Single Dc Power Cord
Dumb terminal For this connection, you can use the standard RJ-45 patch cable supplied with the Netra T1 AC200 and DC200 servers, but you need to insert one end into the DB-25 adapter also supplied. Sun workstation...
Page 81 Modem For this connection, you can use the standard RJ-45 patch cable supplied with the Netra T1 AC200 and DC200 servers, but you need to insert one end into the DB-25 adapter also supplied. Note – Do not us the Serial A/LOM port for binary data transfers. To perform anything other than ASCII transfers, use the port labeled Serial B.
Page 82: Connecting To A Terminal Server
Cisco L2511 Asynchronous Breakout Cable Patch panel Netra T1 server Patch Panel Connection Between a Cisco L2511 and a Netra T1 Server FIGURE 6-3 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 83: Figure 6-4 Serial Port Pins 1 To
Note – When viewed from the rear of the Netra T1 server, pin 1 of the RJ-45 serial port is on the left, pin 8 on the right. Serial Port Pins 1 to 8 FIGURE 6-4 Serial Port Connection to a Terminal Server TABLE 6-1 Pinout on Netra T1 server Signal to connect to on Terminal Server...
Page 84: Using A Db-25 Adapter For Your Serial Link
Pin 7 (Signal Ground) Pin 5 (Signal Ground) Pin 7 (Signal Ground) Pin 6 (RXD) Pin 2 (TXD) Pin 7 (DSR) Pin 20 (DTR) Pin 8 (CTS) Pin 4 (RTS) Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 85: Using A Db-9 Adapter For Your Serial Link
6.3.3 Using a DB-9 Adapter for Your Serial Link To connect to a terminal that has a 9-pin serial connector, connect one of the Netra T1 server’s serial ports to a DB-9 (9-pin) adapter that performs the pin crossovers listed in TABLE 6-3 Note –...
Page 86: Settings For The Serial Connections
(The serial port is a male 9-pin D-type connector.) 1. Connect the RJ-45 to RJ-45 patch cable (supplied with the server) to the Serial A/LOM port on the back panel of the Netra T1 server. 6-10 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 87: Figure 1 Connecting The Netra T1 Server To The Serial Port On A Laptop
2. Connect the other end of the patch cable to the RJ-45 connector on the silver- colored DB25 (25-way DSUB male-to-female 8 POS RJ-45) adapter (part number 530-2889-0x) supplied with the Netra T1 server. Connecting the Netra T1 Server to the Serial Port on a Laptop FIGURE 1 Laptop Netra T1...
Page 88: Using Microsoft Windows Hyperterminal
5. In the COM1 Properties Port Settings window, set the parameters as follows: Bits per second: 9600 Data bits: 8 Parity: None Stop bits: 1 Flow control: specify either “Xon/Xoff” or “None”. 6-12 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 89 Note – Do not select “Hardware” for the Flow control option. Click OK. 6. Your HyperTerminal session is now active. From the File menu, select Properties. 7. In the Properties window, click the Settings tab. On the Settings tab, click the arrow for the “Emulation” option and select VT100. For the “Telnet terminal”...
Page 90 6-14 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 91: Powering On The Netra T1 Server
C H A P T E R Powering On the Netra T1 Server This chapter tells you how to connect to and power on the Netra T1 server. The chapter contains the following sections: Section 7.1, “Preparing to Configure the Server” on page 7-2 Section 7.2, “Powering On the Server”...
Page 92: Preparing To Configure The Server
The tip command assumes that your console is using its ttya port. If you later configure your console to use its ttyb port, you will need to type the following to set up a tip session: # tip /dev/term/b -9600 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 93: Powering On The Server
LOMlite2 From the Console on the Serial A/LOM Port” on page 8-19). Powering On the Server When the Netra T1 AC200 and DC200 servers are connected to mains electricity, they are always either fully powered or in standby power mode. To remove power from a server, you must disonnect its power cables.
Page 94: Powering On The Server For The First Time Without Having Its Details Registered
1. Connect the server to the power supply but do not power it on. 2. Set up a serial connection to the Serial A/LOM port and also a connection to at least one Ethernet hub (as described in Chapter 6). Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 95 3. At the lom> prompt, type the following command to power on the server: lom> poweron For more information about the lom> prompt and the commands that are available from it, see Chapter 8. 4. During booting you will be prompted for certain information. The first question the system asks you is what language you want it to use when it prompts you for the information it needs.
Page 96: Powering On A Standalone Server For The First Time
11. When prompted, give a password (if any) for users logging in as root. 12. When asked if you want the server to perform Automatic Power Saving Shutdown, answer No. Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 97: Clearing Your Configuration And Starting Again
Note – If you answer Yes, the server will automatically put itself into Standby mode after a period of idleness. When you have provided the information the system needs, it will boot. 7.2.4 Clearing Your Configuration and Starting Again If you need to clear the configuration of the Netra T1 server so that you can start the power on process again as if from a previously unused server, follow the instructions below: 1.
Page 98: Using The Power (On/Standby) Switch
The symbols on the switch are as follows: On – Press this to apply power to the server. Standby – Press this to put the server into standby mode. Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 99 What’s Next? When you have powered on the server and booted and logged in, your server is ready to use. For information about managing the server, see Chapter 8 and Chapter 9. Chapter 7 Powering On the Netra T1 Server...
Page 100 7-10 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 101: Part Ii Remote And Local Management
Remote and Local Management PA RT...
Page 103: Managing The Netra T1 Server From The Lom> Prompt
C H A P T E R Managing the Netra T1 Server From the lom> Prompt This chapter introduces the LOMlite2 Lights-Out Management facilities available for the Netra T1 server and tells you how to use the /usr/sbin/lom utility which provides a user interface to the device.
Page 104: Introduction To Lights-Out Management
Turn a Fault LED on. Configure the server to restart automatically after a lockup (see Chapter 9). LOMlite2 device The Location of the Lights-Out Management Device on the System Board FIGURE 8-1 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 105: Powering On Or Resetting The Server From The Lomlite2 Shell
Solaris commands from the console prompt. For information about the LOMlite2 commands available with the Solarisoperatring environment, see Chapter 9. When the Netra T1 AC200 and DC200 servers are connected to a power source, they are always either fully powered or in standby power mode. To remove power entirely from the server you must disonnect its power cables or open all external circuit breakers.
Page 106: Powering The Server On Or Down To Standby Mode
For information about changing the first character of the LOMlite2 escape sequence, see Section 9.3.3, “Changing the First Character of the Sequence for Escaping to the lom> Prompt (lom -X)” on page 9-12. Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 107: Exiting From The Lom> Prompt
8.2.3 Exiting From the lom> Prompt To return to the Solaris console prompt from the lom> prompt, type: lom> console Note – If you have the Serial A/LOM port dedicated to the LOMlite2 device (instead of shared between the LOMlite2 and the console), this command will have no effect.
Page 108: Displaying The Ok Or Kadb Prompt
You must have r-level LOMlite2 permission to use the bootmode command. For information about user privileges, see Section 8.4, “Setting Up LOMlite2 Privileges for Named Users” on page 8-13. Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 109: Table 8-1 Boot Modes
8.2.6.1 Boot Modes Available If you use the bootmode command without arguments, the LOMlite2 device reports just the current boot mode. The boot modes available are listed in TABLE 8-1 Boot Modes TABLE 8-1 Mode Description This option does not represent a boot mode. However, if you have previously dedicated the Serial A/LOM port to the LOMlite2 device and now want to share the port between the console and the LOMlite2 device, you can use the -u option to achieve this.
Page 110: Monitoring The Server From The Lomlite2 Shell
Note – For the locations of the different fans, see Section 8.9, “Checking the Status of the Server’s Fans” on page 8-24. Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 111 Note – If the fans, PSU output, or supply rails fail on your Netra T1 server, you may need to replace components. For information about ordering and installing field- replaceable components, see Chapter 11. lom>environment Fault OFF Alarm 1 OFF Alarm 2 OFF Alarm 3 OFF Fans:...
Page 112: Viewing The Lomlite2 Device's Event Log
Note – If the fans, PSU output, or supply rails fail on your Netra T1 server, you may need to replace components. For information about ordering and installing field- replaceable components, see Chapter 11. 8-10 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 113 8.3.3.2 Viewing the Entire Event Log Type: lom> loghistory [pause x] [level y] where is the number of lines you want the screen to pause after displaying, and is the severity level of the events you want to see. By default, the loghistory command displays all the events in the log and does not pause the display.
Page 114: Checking That A Component Has Been Fixed
To check the status of the component, for example, after attempting to fix it, type: lom> check This causes the LOMlite2 device to update the status of all the components it monitors. 8-12 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 115: Setting Up Lomlite2 Privileges For Named Users
Setting Up LOMlite2 Privileges for Named Users You can specify up to four named users of the LOMlite2 device on a Netra T1 AC200 or DC200 server. By default, no users are set up and therefore no user login prompt appears when you use the LOM escape sequence.
Page 116: Creating A Lomlite2 User Account
LOMlite2 user account that already exists. Note – You must have User Administration (u-level) authorization to set a password for a user (see Section 8.4.1, “Permissions Available for LOMlite2 Users” on page 8-13). 8-14 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 117: Viewing Details Of A Lomlite2 User Account
8.4.4 Viewing Details of a LOMlite2 User Account Type: lom> usershow user name where the is the name of an existing LOMlite2 user account. user name Note – You must have User Administration (u-level) authorization to view the details of a LOMlite2 user account (see Section 8.4.1, “Permissions Available for LOMlite2 Users”...
Page 118: Specifying Permissions For A Named User
LOMlite2 Device’s Configurable Variables” on page 8-17). This stands for “reset permission”. It enables the user you have named to reset the server and to power it on and off using the LOMlite2 device. 8-16 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 119: Quitting A Lomlite2 Named User Session
8.4.8 Quitting a LOMlite2 Named User Session Type: lom> logout This returns you to the LOMlite2 login prompt. Setting the LOMlite2 Device’s Configurable Variables There are some variables that you can use as arguments to the set command in the LOMlite2 shell.
Page 120: Setting The Alarmon N Software Flag
Set the event_reporting variable off by typing: lom> set eventreporting off Note – This is the equivalent of using the lom -E off command from the Solaris shell (see Chapter 9). 8-18 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 121: Separating The Lomlite2 From The Console On The Serial A/Lom Port
Separating the LOMlite2 From the Console on the Serial A/LOM Port By default, the LOMlite2 device shares the Serial A/LOM port with the console, and when it has an event report to send it takes control of the Serial A/LOM port itself, interrupting any console activity you are performing.
Page 122: Sharing Serial A/Lom Between The Lomlite2 And The Console
This means that by default it sends them to the console and stores them in the following file: /var/adm/messages 8-20 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 123: The Lomlite2 Shell Command List
In this file the reports are displayed with a label identifying them as lom reports and indicating their severity. The different levels of severity are, in descending order: 1. Fatal These events might concern, for example, exceeded temperature thresholds or supply rail failures.
Page 124 Adds a user to the LOMlite2 device’s list of permitted users. useradd Deletes a user from the LOMlite2 device’s list of permitted users. userdel Displays the details of a named user’s LOMlite2 account. usershow 8-22 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 125 LOM Commands (Continued) TABLE 8-2 Command Effect Sets or changes a user’s password. userpassword Sets the permission levels for a named user. userperm Displays the version number of the LOMlite2 device. version Chapter 8 Managing the Netra T1 Server From the lom> Prompt 8-23...
Page 126: Checking The Status Of The Server's Fans
Fan 1 Fan 1 Fan 2 Fan 4 Locations of Fans 1, 2, 3, and 4 FIGURE 8-4 To check the status of the fans, type: lom> environment 8-24 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 127: Managing The Netra T1 Server From The Solaris Prompt
C H A P T E R Managing the Netra T1 Server From the Solaris Prompt This chapter tells you how to use the LOMlite2-specific commands available in the Solaris 8 operating environment for monitoring and managing a Netra T1 server. For an introduction to the LOMlite2 device and a description of an alternative user interface to it, see Chapter 8.
Page 128: Monitoring The System From Solaris
Checking the Power Supply Unit (lom -p) To check that the input lines and the output line for the power supply unit are working normally, type: # lom -p PSUs: 1 OK Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 129: Checking The Fans (Lom -F)
Note – If there are any failures of the PSU that affect more than just the input or output lines, Solaris will not run. However, if standby power is present, you can still use the LOMlite2 shell commands described in Chapter 8. 9.1.3 Checking the Fans (lom -f) To check the fans, type:...
Page 130: Checking The Internal Temperature (Lom -T)
To check the internal temperature of the sytem and also the system’s warning and shutdown threshold temperatures, type: # lom -t System Temperature Sensors: 1 enclosure 25 degC : warning 67 degC : shutdown 72 degC System Over-temperature Sensors: 1 cpu status=ok Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 131: Checking The Status Of The Fault Led And Alarms (Lom -L)
9.1.6 Checking the Status of the Fault LED and Alarms (lom -l) To check whether the Fault LED and alarms are on or off, type: # lom -l LOMlite alarm states: Alarm1=off Alarm2=off Alarm3=off Fault LED=on Alarms 1, 2, and 3 are software flags. They are associated with no specific conditions but are available to be set by your own processes or from the command line (see Section 9.3.1, “Turning Alarms On and Off (lom -A)”...
Page 132: Viewing The Configuration Of The Lomlite2 Device (Lom -C)
LOMlite2 Device’s Configuration Data (lom -a) To view all the status data stored by the LOMlite2 device plus the details of the device’s own configuration, type: # lom -a Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 133: Viewing The Event Log (Lom -E)
9.1.10 Viewing the Event Log (lom -e) To see the event log, type: # lom -e n,[x] where n is the number of reports (up to 128) that you want to see and x specifies the level of reports you are interested in. There are four levels of events: 1.
Page 134: Configuring Automatic Server Restart (Asr)
Command (lom -R on)” on page 9-10. However, as long as you have the -R on option set in /etc/rc2.d/S25lom, the Hardware Reset option will always be enabled when you start the system. Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 135: Enabling The Lomlite2 Watchdog Process From Your Own Script Or Command (Lom -W On)
9.2.2 Enabling the LOMlite2 Watchdog Process From Your Own Script or Command (lom -W on) Note – You do not normally need to do this. If you want to configure the LOMlite2 device to perform an automatic server restart after a lockup, see Section 9.2.1, “Configuring the LOMlite2 Watchdog to Restart the System After a Lockup”...
Page 136: Setting The Hardware Reset Option From A Script Or Command (Lom -R On)
# lom -R on To turn the Hardware reset option off from the command line,type: # lom -R off 9-10 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 137: Other Lom Tasks You Can Perform From Solaris
Other LOM Tasks You Can Perform From Solaris This section tells you how to turn the alarms and Fault LEDs on and off by using the lom command. It also tells you how to change the first character of the lom escape sequence, how to stop the LOMlite2 device from sending reports to the Serial A/LOM port, how to remove driver protection from the device driver, how to make the LOMlite2 interface backward compatible, and how to upgrade the firmware on...
Page 138: Changing The First Character Of The Sequence For Escaping To The Lom> Prompt (Lom -X)
LOMlite2 event reports can interfere with information you are attempting to send or receive on the Serial A/LOM port. To stop the LOMlite2 device from sending reports to the Serial A/LOM port, type: # lom -E off 9-12 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 139: Removing Driver Protection From The Lomlite2 Driver (Lom -U)
By default, the Serial A/LOM port is shared by the console and the LOMlite2 device. The LOMlite2 interrupts the console whenever it needs to send an event report. To prevent the LOMlite2 from interrupting the console on Serial A/LOM, turn serial event reporting off.
Page 140: Making The Lomlite2 Interface Backward Compatible (Lom -B)
If you have scripts written to the LOMlite interface on the Netra t1 Model 100/105 server or the Netra t 1400/1405 server and you want to use these scripts on the Netra T1 AC200 or DC200 server, you can add file system links that make this possible. To do so, simply type: # lom -B When you have done this, you will be able to use the old scripts on the new system.
Page 141: Part Iii Troubleshooting And Maintenance
Troubleshooting and Maintenance PA RT...
Page 143: Troubleshooting
C H A P T E R Troubleshooting This chapter lists some problems that you might encounter when setting up or using the Netra T1 server and tells you how to solve them. It also explains how to interpret the LEDs on the server’s front and back panels. The chapter contains the following sections: Section 10.1, “Solutions to Problems You Might Encounter”...
Page 144: Solutions To Problems You Might Encounter
LOMlite2 software from the support CD supplied with Solaris 8 (entitled Software Supplement for the Solaris 8 Operating Environment), you need to apply patch 110208-xx. This patch is available on SunSolve 10-2 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 145 Problem: Card Not Recognised During Installation or Bootup The Netra T1 AC200 and DC200 servers are fitted with a System Configuration Card. If the card moves during transit then the server will not be able to read the card, and as a result will not boot.
Page 146: Interpreting The Front And Back Panel Leds
The voltage on one of the server’s output supply rails is too high. (By default, this causes the server to shut down. For information about configuring the server not to shut down in this condition, see Appendix A.) 10-4 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 147: Figure 10-1 Front Panel Power And Fault Leds
The temperature inside the CPU is too high. (This causes the server to shut down.) Power Fault Front Panel Power and Fault LEDs FIGURE 10-1 The Netra T1 contains four rear panel LEDs (see FIGURE 10-2 A Power LED This replicates the Power LED on the front panel. A Fault LED This replicates the Fault LED on the front panel.
Page 148 10-6 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 149: Replacing A Server Or Replacing Individual Components
C H A P T E R Replacing a Server or Replacing Individual Components If you ever need to replace an entire Netra T1 server, this chapter describes how to transfer the old server’s configuration information (including its MAC address, serial number and NVRAM settings) to a new server by using the old server’s configuration card.
Page 150: Replacing A Server
11.1 Replacing a Server The Netra T1 AC200 and DC200 servers contain a memory card (accessible by removing the unit’s front bezel) called the System Configuration Card. This card contains the values for the system’s IDPROM (Host ID, MAC address, date and Cyclic Redundancy Check value) and NVRAM variables.
Page 151: Figure 11-1 Replacing The System Configuration Card
Caution – Do not handle the System Configuration Card unless you need to transfer it to another system. If you need to handle it for this reason, avoid contact with the gold terminals on the underside of the card. Tie-wrap hole Replacing the System Configuration Card FIGURE 11-1 Chapter 11 Replacing a Server or Replacing Individual Components...
Page 152: Field Replaceable Units
Note – Except for the 18 Gbyte hard disk, you can only use the FRUs in this list in Netra T1 AC200 and DC200 servers. They are not for use in the earlier Netra t1 Model 100 or Model 105 servers.
Page 153: Replacing The Memory Card Reader For The System Configuration Card
11.3 Replacing the Memory Card Reader for the System Configuration Card Caution – The procedure below is for the attention of qualified service engineers only. Before touching or replacing any components inside the Netra T1 server, disconnect all cables and follow the instructions in Section 4.2, “Opening the Netra T1 Server”...
Page 154: Figure 11-2 Removing The System Configuration Card Reader
Card reader’s cable connector Removing the System Configuration Card Reader FIGURE 11-2 11-6 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 155: Replacing The Cd-Rom Drive, Cable, And Paddleboard
11.4 Replacing the CD-ROM Drive, Cable, and Paddleboard Caution – The procedure below is for the attention of qualified service engineers only. Before touching or replacing any components inside the Netra T1 server, disconnect all cables and follow the instructions in Section 4.2, “Opening the Netra T1 Server”...
Page 156: Figure 11-3 Replacing The Cd-Rom Paddleboard
13. Replace the system cover and tighten the captive screw (see FIGURE 4-9 Section 4.7, “Replacing the Server’s Top Cover” on page 4-15). Plastic bracket Card reader’s cable connector Replacing the CD-ROM Paddleboard FIGURE 11-3 11-8 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 157: Replacing The Nvram Chip
11.5 Replacing the NVRAM Chip Caution – The procedure below is for the attention of qualified service engineers only. Before touching or replacing any components inside the Netra T1 server, disconnect all cables and follow the instructions in Section 4.2, “Opening the Netra T1 Server”...
Page 158: Figure 11-4 The Location Of The Nvram Chip
4. Holding the new NVRAM chip carrier in a similar fashion between your thumb and forefinger, position it over the socket and press firmly until the connectors engage. 11-10 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 159: Figure 11-5 Replacing The Nvram Chip
5. When you have reconnected the cables and powered the server on, type the following at the ok prompt, using the values you noted in Step 1: ok reset-all ok setenv diag-switch? noted_value ok setenv diag-level noted_value ok reset-all Replacing the NVRAM Chip FIGURE 11-5 6.
Page 160: Replacing The System Board
6. Remove the DIMMs from their slots (see Section 4.5, “Installing and Removing Memory” on page 4-9). 7. Remove the rear fan subassembly (see Section 11.8, “Replacing the Rear Fan Subassembly (Fans 1 and 2)” on page 11-17). 11-12 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 161: Installing The New System Board
8. Unscrew the system board protection/support block (between the PSU and hard disk drive bay 1) and slide it back as far as the PSU (see FIGURE 11-6 9. Unscrew and remove the PCI card slide retainer (see FIGURE 11-6 10.
Page 162: Figure 11-6 The System Board
Alignment stand-off System board protection/ support block SCSI pillars The System Board FIGURE 11-6 11-14 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 163: Replacing The Power Supply Unit
11.7 Replacing the Power Supply Unit Caution – The procedure below is for the attention of qualified service engineers only. Before touching or replacing any components inside the Netra T1 server, disconnect all cables and follow the instructions in Section 4.2, “Opening the Netra T1 Server”...
Page 164: Figure 11-7 Replacing The Power Supply Unit
Step 5 Step 2 Step 3 Replacing the Power Supply Unit FIGURE 11-7 11-16 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 165: Replacing The Rear Fan Subassembly (Fans 1 And 2)
11.8 Replacing the Rear Fan Subassembly (Fans 1 and 2) Caution – The procedure below is for the attention of qualified service engineers only. Before touching or replacing any components inside the Netra T1 server, disconnect all cables and follow the instructions in Section 4.2, “Opening the Netra T1 Server”...
Page 166: Figure 11-8 Replacing The Rear Fan Subassembly (Fans 1 And 2)
Replacing the Rear Fan Subassembly (Fans 1 and 2) FIGURE 11-8 11-18 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 167: Replacing Fan 3 (Cpu Fan)
11.9 Replacing Fan 3 (CPU Fan) Caution – The procedure below is for the attention of qualified service engineers only. Before touching or replacing any components inside the Netra T1 server, disconnect all cables and follow the instructions in Section 4.2, “Opening the Netra T1 Server”...
Page 168: Figure 11-9 Pressing Down On The Long Arm Of The Clip To Remove Fan
Pressing Down on the Long Arm of the Clip to Remove Fan 3 FIGURE 11-9 11-20 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 169: Iv Appendixes
IV Appendixes PA RT...
Page 171: Configuring The Lomlite2 Device Driver
A P P E N D I X Configuring the LOMlite2 Device Driver This appendix describes the driver parameters you can set in the lom.conf configuration file. Some of these parameters are also configurable by means of the LOMlite2-specific Solaris commands described in Chapter 9. The appendix contains the following sections: Section A.1, “The LOMlite2 Device Driver”...
Page 172: The Lomlite2 Device Driver
The LOMlite2 Device Driver The LOMlite2 driver software included in Solaris 8 (10/00) is as follows: /platform/sun4u/kernel/drv/lom (the lom driver (32-bit)) /platform/sun4u/kernel/drv/sparcv9/lom (the lom driver (64-bit)) /platform/sun4u/kernel/drv/lom.conf (the driver configuration file) Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 173: Configuring The Lomlite2 Device Driver
Configuring the LOMlite2 Device Driver The full list of parameters you can set in this file is given in TABLE A-1 LOM Configuration File Parameters TABLE A-1 Field Format Default Effect Boolean Causes the LOMlite2 to reset the wdog_reset= 0=FALSE Netra T1 after a watchdog 1=TRUE timeout.
Page 174: Table A-1 Lom Configuration File Parameters
LOMlite2 user security facilities 1=TRUE even if user security has been configured. You can use this parameter to set up users again if your users have forgotten their passwords. Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 175 LOM Configuration File Parameters (Continued) TABLE A-1 Field Format Default Effect Multiples Specifies the idle period after serial_timeout= of 4 secs which the LOMlite2 device gives control of the Serial A/LOM port back to the console when it has finished sending a report.
Page 176 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 177: System Board Jumper Settings
A P P E N D I X System Board Jumper Settings This appendix describes the functions and factory-default settings of the jumpers on the system board of the Netra T1 server.
Page 178: Table B-1 Factory-Default Jumper Settings
This jumper tells the CD-ROM drive (if one is installed) that it is a Master ATA device. For the CD-ROM drive currently available for the Netra T1 system, this jumper must be Open. Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 179: Figure B-1 System Board Jumper Locations And Default Settings
JP17 Pin 5 Pin 1 JP16 Pin 1 JP14 JP13 JP15 System Board Jumper Locations and Default Settings FIGURE B-1 Appendix B System Board Jumper Settings...
Page 180 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 181 Index cover removal, 4-4 AC power replacement, 4-15 warnings, 6-3 crossover cable, 6-8, 6-9 acoustic noise, 1-9 current alarms in-rush, 2-2 checking the status of, 9-5 operating, 2-2 alarms, setting, 8-21, 9-11 altitude, 1-9 Asynchronous Breakout Cable (Cisco), 6-6 ATM cards (optional), 1-5 automatic server restart, 9-8 DB-25 adapter, 6-2, 6-8 DB-9 adapter, 6-9...
Page 182 LOM’s Event Log, 8-10 in-rush current, 2-2 locating system components, 4-1 installation log, viewing, 8-10 CD-ROM drive, 4-7 LOMlite2 device CD-ROM with cable and paddleboard, 11-7 Index-2 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...
Page 183 conﬁguration variables, 8-17 installing, 4-11 removing driver protection, 9-13 part numbers of available cards, 1-5 separating from the console on Serial A, 8-19 removing, 4-14 sharing Serial A between the console and the pinout LOMlite2 device, 8-20 serial port, 6-6, 6-7 upgrading ﬁrmware, 9-14 power version number, 8-23...
Page 184 9-3 supply rails, A-4 surge suppression devices, 3-2 system board, 11-9, 11-14, B-3 replacing, 11-12 system components, 4-6 system conﬁguration card not recognised during installation or bootup, 10- Index-4 Netra T1 AC200 and DC200 Server User’s Guide • August 2001...

This manual is also suitable for:

Dc200 Netra t1 ac200 Netra t1 dc200

Sun Microsystems AC200 User Manual

Table of Contents

Figures

Introduction

2 Power and Cooling

3 Using DC Power

Installing Optional Hardware Components

5 Installing the Server into a Rack

6 Connecting the Cables

7 Powering on the Netra T1 Server

Part II Remote and Local Management

Managing the Netra T1 Server from the Lom> Prompt

9 Managing the Netra T1 Server from the Solaris Prompt

Part III Troubleshooting and Maintenance

10 Troubleshooting

Replacing a Server or Replacing Individual Components

IV Appendixes

Configuring the Lomlite2 Device Driver

System Board Jumper Settings

Quick Links

Chapters

Troubleshooting

Need help?

Questions and answers

Related Manuals for Sun Microsystems AC200

Summary of Contents for Sun Microsystems AC200