Related Manuals for Pace Sodrtek HW50
Summary of Contents for Pace Sodrtek HW50
- Page 1 Operation and Maintenance Manual for the HW 50 Soldering System P/N 5050-0533 Voltage Part Number ™ HW 50 HEATWISE System 115 VAC 8007-0425 ™ HW 50 HEATWISE System 230 VAC 8007-0426...
-
Page 2: Table Of Contents
Optional Instant Setback Cubby................8 Corrective Maintenance ....................8 Handpieces......................8 Power Source .......................8 Replacement Power Modules ..................9 Packing Contents ......................9 Service ...........................9 “SODRTEK by PACE” LIMITED WARRANTY STATEMENT........10 Contact Information.......................11 ©2004 PACE Inc., Annapolis Junction, Maryland Page 2 of 11 All Rights Reserved... -
Page 3: General Information
General Information Introduction Thank you for purchasing the PACE model HW 50 Soldering System. This manual will provide you with the information necessary to properly set up, operate, and maintain the HW 50. The HW 50 system is available in either 115 VAC or 230 VAC versions, which incorporate a highly responsive, closed loop control system providing up to 55 Watts of total output power. -
Page 4: Parts Identification
Parts Identification Front Panel LED Handpiece Connection Power Switch Power Module Receptacle Auto-Off Switch Earth Ground Receptacle AC Power Receptacle/Fuse Holder Fuse Optional Instant Setback Cubby Receptacle ©2004 PACE Inc., Annapolis Junction, Maryland Page 4 of 11 All Rights Reserved... -
Page 5: Safety
Always store the handpiece in its holder. Be sure to place the handpiece in its holder after use and allow for cooling before storing. 5. Always use PACE systems in a well ventilated area. A fume extraction system such as those available from PACE are highly recommended to help protect personnel from solder flux fumes. -
Page 6: Tip & Tool Stand
3. Turn the connector housing clockwise to lock in place. System Power Up 1. Insert the female end of the power cord into the AC Power Receptacle on the rear panel of the power source. ©2004 PACE Inc., Annapolis Junction, Maryland Page 6 of 11 All Rights Reserved... -
Page 7: Definitions
3. The LED indicator will turn amber while the tip is heating to the desired performance level. 4. Once the tip has reached the desired heat level, the LED indicator will turn green and the system is ready to use. ©2004 PACE Inc., Annapolis Junction, Maryland Page 7 of 11 All Rights Reserved... -
Page 8: Auto-Setback And Auto-Off Features
Defective Heater Change Tip Cartridge. Refer to the TD-100/MT- not heat 100 Handpiece manual for the maintenance procedures. Power Source Contact PACE Malfunction Power Source Corrective Maintenance ©2004 PACE Inc., Annapolis Junction, Maryland Page 8 of 11 All Rights Reserved... -
Page 9: Replacement Power Modules
Power Module Kit 1207-0365-P3 1207-0365-P3 Contains 6.5, 7, & 7.5 Modules Hot Grip Removal Pad 1100-0307-P1 1100-0307-P1 Service Please contact PACE or your local distributor for service and repair. ©2004 PACE Inc., Annapolis Junction, Maryland Page 9 of 11 All Rights Reserved... -
Page 10: Sodrtek By Pace" Limited Warranty Statement
Warranty service may be obtained by contacting the appropriate PACE Company or local Authorized PACE distributor as set forth below to determine if return of any item is required, or if repairs can be made by the user in the field. Any warranty or other claim with respect to the products must be made with sufficient evidence of purchase and date of receipt, otherwise user’s rights under this warranty shall be... -
Page 11: Contact Information
PACE Incorporated retains the right to make changes to specifications contained herein at any time, without notice. Contact your local authorized PACE Distributor or PACE Incorporated to obtain the latest specifications. The following are trademarks and/or service marks of PACE, Incorporated, MD, USA: ™...