Pace ST 25 Operation And Maintenance Manual
  1. Manuals
  2. Brands
  3. Pace Manuals
  4. Soldering Gun
  5. ST 25
  6. Operation and maintenance manual

Pace ST 25 Operation And Maintenance Manual

Hide thumbs Also See for ST 25:
Table of Contents

Advertisement

Quick Links

WORLDWIDE
Operation and Maintenance Manual for the
ST 25 & ST 35 Soldering Systems
P/N 5050-0452
Rev D

Advertisement

Table of Contents
loading

Related Manuals for Pace ST 25

Summary of Contents for Pace ST 25

  • Page 1 WORLDWIDE Operation and Maintenance Manual for the ST 25 & ST 35 Soldering Systems P/N 5050-0452 Rev D...

  • Page 2: Table Of Contents

    Corrective Maintenance Power Source ..................... 11 Handpieces ......................11 PS-90 Heater Replacement................12 Packing List/Spare Parts ....................12 Service.......................... 13 Limited Warranty Form ....................13 Contact Information ...................... 14 ©2001 PACE Inc., Laurel, Maryland Page 2 of 14 All Rights Reserved...

  • Page 3: Introduction

    ST 25 or ST 35. The ST 25 and ST 35 systems are available in either 115 VAC or 230 VAC versions, which incorporates a highly responsive SensaTemp (closed loop) control system providing up to 80 Watts of total power to a single output channel.

  • Page 4: Safety Guidelines, English Language

    Always store the handpiece in its holder. Be sure to place the handpiece in its holder after use and allow for cooling before storing. 5. Always use PACE systems in a well ventilated area. A fume extraction system such as those available from PACE are highly recommended to help protect personnel from solder flux fumes.

  • Page 5: Safety Guidelines, German Language

    5. Utilizzare sempre I stazioni PACE in una zona be aerata per proteggere il personale dai fumi. É fortemente raccomandato un sistema di aspirazione (dei fumi) come quello disposta dalla PACE.

  • Page 6: Safety Guidelines, Portuguese Language

    NUNCA TOCAR nem na resistencia de aquecimento nem na ponta. Pode resultar em queimaduras severas. 4. Os suportes para pontas e ferros da PACE, foram concebidos para uso especifico, e para proteger o operador de queimaduras acidentais. Coloque sempre os ferros nos respectivos suportes.

  • Page 7: Safety Guidelines, Swedish Language

    Följande säkerhetsföreskrifter måste förstås och följas av personal som använder eller utför service på PACE produkter. 1. RISK FÖR STRÖMSTÖT - Service / Reparation av PACE produkter får endast utföras av aktoriserad service personal. Strömförande delar kan kommas åt när produkten är isärplockad.

  • Page 8: System Set-Up

    Mounting Options The ST 25 and ST 35 can be placed directly on a work bench and can be stacked if more than one system is used. The ST 35 can also be mounted under a workbench or shelf to conserve space. To mount the system in this way: 1.

  • Page 9: System Power Up

    NOTE: Periodically, clean the heater bore with a properly sized wire brush (3/16" O.D. to insure optimum heat transfer and proper tip grounding when non- PERMAGROUND tips are used. ©2001 PACE Inc., Laurel, Maryland Page 9 of 14 All Rights Reserved...

  • Page 10: Operation

    The ST 35 system is tested for temperature accuracy at the factory and can be checked for calibration according to PACE requirements. Also, a temperature setting normally used by the operator can be adjusted to the precise temperature indicated on the Dial/Display. No internal adjustments can be made to the power supply.

  • Page 11: Corrective Maintenance

    The following “Heater Assembly Checkout Procedures” (Table 2) is applicable to all PACE SensaTemp handpieces used with the ST 25 or ST 35 system except for the TT-65 and DTP-80 handpieces. Refer to the applicable manuals for troubleshooting procedures pertinent to these handpieces.

  • Page 12: Heater Replacement

    5. Push the Heater Assembly fully into the handle. 6. Replace the Heater Retaining Nut and tighten by hand. Packing List Quantity Supplied ST 25 or ST 35 ST 25 or ST 35 with PS-70 with PS-90 ST 25 TT...

  • Page 13: Service

    Warranty Information: LIMITED WARRANTY PACE warrants that this equipment will be free of defects in materials and workmanship for a period of one (1) year from the date of receipt by original purchaser. This warranty does not cover repair or replacement required as a result of misuse, mishandling or improper storage.

  • Page 14: Contact Information

    PACE, Incorporated retains the right to make changes to specifications contained herein at any time, without notice. The following are registered trademarks and/or service marks of PACE, Incorporated, Laurel, Maryland, USA and may only be used to identify genuine PACE products or services.

This manual is also suitable for:

St 35

Table of Contents