Related Manuals for Pace MBT360
Summary of Contents for Pace MBT360
- Page 1 Operation and Maintenance Manual for the MBT360® Digital Soldering/Desoldering Rework System Consisting of power source 7008-0341-01 or 7008-0341-02 Manual 5050-0608 Revision Date: 4/25/2022 For firmware version 1.3...
-
Page 2: Table Of Contents
MBT360 Compatible Handpieces......................2 System Features ............................3 Safety Guidelines ............................4 Initial Set-Up ............................... 5 Attaching Tip & Tool Stand to MBT360 ....................5 Instant SetBack Tool Stand Connection ....................5 Handpiece Connection ..........................6 System Power............................6 Basic Operation ............................7 Definitions ............................... -
Page 3: General Information
The MBT360 unit is available in either 120 VAC or 230 VAC versions. The 230 VAC version system bears the CE Conformity Marking which assures the user that it conforms to all the requirements of (EU) directive EMC 89/336/EEC &... -
Page 4: Capabilities
A manual is available for each handpiece with descriptions of the applications and recommended procedures for that tool. The MBT360 allows a total of two AccuDrive handpieces and one SensaTemp to be plugged into the continuously active Power Ports on its front. The dual-purpose vacuum/pressure pump system with PACE’s patented SNAP- VAC Technology, provides the most vacuum available for desoldering applications. -
Page 5: System Features
CH 3 POWER RECEPTACLE - Provides for connection of power, tip ground, sensing circuitry, and finger switch input between the MBT system and handpiece connected to Channel 3 (CH 3). ©2022 PACE Inc., Vass, North Carolina, All Rights Reserved Page 3... -
Page 6: Safety Guidelines
DO NOT touch the heater or the tip. Severe burns may result. PACE Tip & Tool Stands are designed specifically for use with the associated handpiece and houses it in a manner that protects the user from accidental burns. -
Page 7: Initial Set-Up
Attaching Tip & Tool Stand to MBT360 Attach the stand to the side of the MBT360’s chassis, using the following procedure. Refer to illustration. 1. Insert the two enclosed hex head Mounting Screws into the slot on the side of the chassis. Some kits may contain four mounting screws: two with small heads and two with large heads. -
Page 8: Handpiece Connection
Handpiece Connection The MBT360 will work with AccuDrive or SensaTemp hand pieces and tip heater cartridges via the three channels on its front panel, two for use with AccuDrive hand pieces and one for use with SensaTemp tools. Caution: Using handpieces from other PACE product lines may result in damage to the equipment. Only use tip heater cartridges from the AccuDrive collection (the ones with blue caps on the end). -
Page 9: Basic Operation
LED is Steady Amber - Continuous power is being delivered to the handpiece. This condition is evident when the system is first powered up (handpiece heater cold) or the temperature setting is increased. ©2022 PACE Inc., Vass, North Carolina, All Rights Reserved Page 7... -
Page 10: Temperature Adjust Mode
10. If “Yes” was chosen, the unit will ask you to “Enter Tip Temp.” for Channel 2. Use the Scroll Up Key ( ) or Scroll Down Key ( ) to input the temperature measured during step 4. When done, press the Program Key ( ) to return to normal operating mode. ©2022 PACE Inc., Vass, North Carolina, All Rights Reserved Page 8... -
Page 11: Sensatemp Temperature Offset
“Customizing Your System” for more details. Factory Settings The MBT360 system is equipped with several features which may be adjusted by the user. Listed below are the default settings of each. To change and/or learn about any of these features, refer to the “Customizing Your System”... -
Page 12: Temperature Scale
Use the Scroll Down Key ( ) to select “No” and dispose of the currently stored password and move on to the next step. Temperature Scale The MBT360 can display temperatures in Celsius or Fahrenheit. The display now shows the stored default Temperature Scale, either °C or °F. -
Page 13: Automatic Setback Timer
Press and release the Program Key ( ) to proceed to the next step. • SetBack Reset The MBT360 may have more than one handpiece connected. SetBack Reset provides fine control of how each handpiece channel can be brought out of SetBack by selecting them individually or by returning all of them to normal operation at once. -
Page 14: Autooff
“OS Mode 2” (Offset Mode 2) Offset will clear to zero if the handpiece is removed from the system, but only removing the tip will keep the current offset and the indicator dot will begin BLINKING. A ©2022 PACE Inc., Vass, North Carolina, All Rights Reserved Page 12... -
Page 15: Lcd Contrast
050. Use the keypad ( ) to increase or • decrease the contrast as needed. Press and release the PROGRAM Key to proceed to the next step • ©2022 PACE Inc., Vass, North Carolina, All Rights Reserved Page 13... -
Page 16: Led Backlite
Down Arrow while powering on the unit. If appears functional but the Contrast settings out issue is not resolved, contact PACE for display is blank of adjustment assistance. ©2022 PACE Inc., Vass, North Carolina, All Rights Reserved Page 14... -
Page 17: Display Message Codes
Fuse 1.25 Amp, Time Lag (for 120V) 1159-0275-01-P5 Fuse 0.63 Amp, Time Lag (for 230V) 1159-0275-02-P5 MBT Motor/Pump Assembly 1336-0083-P1 Motor/Pump Rebuild Kit 6993-0260-P1 Optional under shelf mounting bracket 1321-0609-P1 ©2022 PACE Inc., Vass, North Carolina, All Rights Reserved Page 15... -
Page 18: Optional Accudrive® Blue Series Tip-Heater Cartridges
For delicate micro-soldering to challenging, high thermal mass applications Ultra-Performance Tips Optimized tip geometries and increased thermal pipeline deliver maximum heat throughput Service Please contact PACE or your local distributor for service and repair. ©2022 PACE Inc., Vass, North Carolina, All Rights Reserved Page 16... -
Page 19: Pace Limited Warranty Statement
(6) months. Monitors, computers, and other brand equipment supplied but not manufactured by PACE are covered under their respective manufacturer’s warranty in lieu of this Warranty.