Channel Level; Fader Function - Denon AVR-1909 Owner's Manual

ENGLISH
II
Symbols used to indicate buttons in this manual
Button located on both the main unit and the remote control
unit
Button only on the main unit
Button only on the remote control unit
<SPEAKERS>
<INPUT MODE>
I
'-r---jr-"-f~-"~[;j
QUICK SELECT <SELECT/ENTER>,
<POWER>
irf!S~JJ2~~0J
QUICK SELECT
[Front]
[Rear]
f::::. V <11>
--+----:8- ' " ' .
63
Operations
Connect the HOMI to the AVR-1909 with equipment
1
compatible with the HOMI control function (lGFpage
BUTION
•
62).
<BUnON>
•
[BUTIONI
•
Put the power on for all the equipment connected to
2
theHOMI.
Check the settings for all the equipment connected to
3
the HOMI and make HOMI available to them.
' *
Please consult the operating instructions for the connected
equipment to check the settings.
' *
Steps 1-3 do not have to be repeated once started.
' *
Carryout steps 2 and 3 should any of the equipment be plugged
out.
Switch the television input to the HOMI connected to
4
the AVR-1909.
Switch the AVR-1909 input to the HOMI input source
5
and check if the picture from the player is ok.
<JI>
Put the television power on" standby and check if the
6
AVR-1909 goes into standby.
If the AVR-1909 does not work please check the following.
• Is the menu "Manual Setup" - "HOMI Setup" - "HOMI Control"
((Fpage 32) set to "ON"?
• Is the menu" Manual Setup" - "HOMI Setup" - "Power Off Control"
((Fpage 32) set to "ON"?
• Is the control function used for the television HOMI properly set
(Check the television operating instructions for details.)
• Should any of the operations below be performed, the interlocking
function may be reset, in which case, repeat step's 2 and 3
• Menu "Input Setup" - "Assign" - "HOMI In" (D2W"page 42) setting
has changed.
• There is a change to the connection between the equipmen and
the HOMI, or an increase in equipment.
' < ;5-:
._)~~--
'--10:---
[CH SELECT/
ENTER]
1

Channel Level

You can adjust the channel level either according to the playback
sources or to suit your taste, as described below.
<SELECT/ENTER> [CH SELECT / ENTER].
Press or
1
Channe I Vo I urne
SR
I I
SBR
O. OdB
FR SBL
O. OdB
SW SL
O. OdB
Fad e r
FRONTC .REAR
<SELECT/ENTER>
Use L:::. \l,
2
to select the speaker.
The speaker that can be set switches each time one of the
buttons is pressed.
3
<1 I>
Use to adjust the volume.
' *
In the case of a sub woofer, reducing the volume when it is at
"-12 dB" will change the setting to "OFF" (none).
-N,n.
When the input source is "iPod': you cannot perform channel level
setting.

Fader Function

7
This function lets you adjust (fade) the sound from all the front or
rear speakers at once.
1
<SELECT/ENTER> [CH SELECT / ENTER].
Press or
<SELECT/ENTER>
Press L:::. \l,
2
ENTER]
to select "Fader".
_ - - ._-_._--_._-
.
<11>
Use to adjust the volume of the speakers.
3
(<I: front, rear)
[>:
• The fader function does not affect the subwoofer.
• The fader can be adjusted until the volume of the speaker adjusted
to the lowest value is -12 dB.
o
O. dB
o
O. dB
o
O. dB
o
O. dB
[CH SELECT / ENTER]
or
I
[CH SELECT
or