Clone Mode - Kenwood TK-6110 Service Manual

2. How to Enter Each Mode
Mode
User mode Power on
PC mode Turn on the transceiver.
Then, set the transceiver to PC mode from
the menu in KPG-59D.
Panel test mode Hold down the [MON] key, turn the radio
power on.
Main programming Hold down the [A] key, turn the radio
mode power on.

3. Clone Mode

1. Turn the master side transceiver power on with the
[SCN] key held down. The master side transceiver dis-
plays "CLONE".
2. Set the power switch on the slave side transceiver to
ON.
3. Connect the cloning cable (E30-3382-05) between the
master side transceiver (source) and slave side trans-
ceiver (clone).
4. Press the [SCN] key on the master side transceiver to
start cloning.
5. The TX LED on the master side transceiver flashes when
cloning starts and an "END" message appears when
cloning ends.
6. The BUSY LED on the slave side transceiver flashes.
7. When a problem occurs during cloning, an "ERROR"
message appears on the slave side transceiver.
8. Pressing the [SCN] key sets clone mode again.
[SCN]
[SCN]
CLONE START
4. Main Programming Mode
4-1. Preface
Flash memory is mounted on the transceiver. This al-
lows the transceiver to be upgraded when new features are
released in the future. (For details on how to obtain the firm-
ware, contact Customer Service.)
4-2. Connection Procedure
Connect the transceiver to the personal computer (IBM
PC or compatible) with the interface cable (KPG-46). (Con-
nection is the same as in the PC Mode.)
REALIGNMENT
Operation
[SCN]
END
4-3. Programming
1. Set the transceiver to Main Programming Mode.
2. Connect the KPG-46 to the transceiver.
3. Start up the programming software (KPG-59D), select
"firmware program" in the "Program" item, and press
the Return key on the personal computer. This starts up
the firmware programmer.
4. The top screen is displayed. Press any key to advance
to the next screen.
5. Set the communications speed (normally, 115,200bps)
and communications port in the Setup item.
6. Set the firmware to be updated by File select.
7. Held down the [A] key. Turn the transceiver power on.
Until the display change to "PROG1152"
8. Check the connection between the transceiver and the
personal computer, and make sure that the transceiver
is in the Main Programming Mode.
9. Press F10 on the personal computer. A window opens
on the display to indicate progress of writing. When the
transceiver starts to receive data, "PG" is appeared on
2 digit sub display.
10. If writing ends successfully, the TX LED on the trans-
ceiver lights and the checksum is displayed.
11. If you want to continue programming other transceiv-
ers, repeat steps 5 to 8.
Notes :
• To start the Firmware Programmer from KPG-59D, the
Fpro path must be set up by KPG-59D setup.
• This mode cannot be entered if the Main Programming
mode is set to Disable in the Programming software
(KPG-59D).
4-4. Function
1. If you press the [SCN] key while "PROG1152" is dis-
played, the checksum is displayed. If you press the [C]
key while the checksum is displayed, "PROG1152" is
redisplayed.
2. A transmission speed can be selected by pressing the [C]
key while "PROG1152" is displayed.
115200bps : PROG1152
19200bps : PROG 192
38400bps : PROG 384
57600bps : PROG 576
Note :
Normally, write in the high-speed mode.
5. Panel Test Mode
Setting method refer to ADJUSTMENT.
TK-6110
9