Kenwood TK-6110 Service Manual page 6

TK-6110
3-4. Sub LCD Display
You can use 3-digit 7-segment the display to display the
channel number. It is useful when the main (8-digit 13-seg-
ment) display indicates channel name.
3-5. Emergency Channel Display
The transceiver can be programmed to display "EMER-
GENCY" channel name when it is in emergency mode.
If you set to "off" by KPG-59D the transceiver shows
selected group/channel/status before entering to the emer-
gency mode however the transceiver is in an emergency
mode.
3-6. Clear to Transpond
The transceiver waits the transpond of 2-Tone/DTMF if
channel is busy until channel open. This feature replies to
the transpond signal when the caller returns to receive.
3-7. Mode (Enable/Disable)
The transceiver has many special modes mainly for main-
tenance.
· Panel Test mode
· Clone mode
· Main programming mode
It is possible to set enable/disable for each mode. We
recommend to set these mode to Disable after set up to
save contents.
3-8. ID
The transceiver is capable to have ID. The format is
DTMF. The timing that the transceiver sends ID is program-
mable.
Begin of TX : Connect ID is send on beginning of trans-
mission.
End of TX : Disconnect ID is send on end of transmission.
Both : Connect ID is send on beginning of transmission
and disconnect ID is send on end of transmission.
Off : Sending ID function is disabled.
There is also "PTT ID" setting for each channel. Refer
"PTT ID" of channel feature.
3-9. OST (Operator Selectable Tone)
The transceiver is capable to have "OST" function and 16
tone pair (QT/DQT) with max 8-digit name for each tone pair.
• "OST" Back Up
The transceiver is programmable the selected "OST"
code is memorized or not. If you set to Disable (no memo-
rized), the "OST" function always starts at "off".
3-10. "TOT" (Time-Out Timer)
The transceiver has the "TOT". This parameter selects
the period of time users can continuously transmit.
When the selected period passes, the transceiver gener-
ates an warning tone and stops the transmission.
6
OPERATING FEATURES
3-11. "TOT" Pre-Alert
eter selects the time at which the transceiver generates
"TOT" pre-alert tone before "TOT" is expired.
from a TOT pre-alert tone.
3-12. "TOT" Re-Key Time
time you can not transmit after "TOT" exceeded. After
"TOT" re-key time expired you can transmit again.
3-13. "TOT" Reset Time
minimum wait time allowed during a transmission that will
reset the "TOT" count.
after PTT is released unless the "TOT" reset timer has ex-
pired.
3-14. Signalling
for any channel programmed with the option signalling (2-
Tone/ DTMF).
4. Channel Features
ware (KPG-59D).
4-1. Alphanumeric Display (Channel Name)
the alphanumeric display for channel name. The total text
size of channel name are 8-digits.
The transceiver has "TOT" pre-alert timer. This param-
"TOT" will be expired when the selected time passes
The transceiver has "TOT" re-key timer. This timer is the
The transceiver has "TOT" reset timer. This timer is the
"TOT" reset time causes the "TOT" to continue even
Signalling "AND/OR" sets the audio unmute condition
AND : "AND" requires both the valid option signalling
and the programmed QT/DQT to be received for audio to
unmute (and initiate an option signalling decode alert).
OR : "OR" requires either the valid option signalling or
the programmed QT/DQT to be received for audio to
unmute (an option signalling decode alert is only initiated
if the proper option signalling is decoded).
You can use these features using the programming soft-
The programming software (KPG-59D) enables you to set
The characters can be used as shown in Figure 1.
A B C D E F G H I
J K L M N O P Q R
S T U V W X Y Z
1 2 3 4 5 6 7 8 9
0 -
Fig. 1
All on