Kenwood TK-6110 Service Manual page 7

4-2. Option Signalling
The transceiver is programmable to the option signalling
(2-Tone decode program 1, 2-Tone decode program 2, 2-
Tone decode program 3, DTMF decode) to each channel. It
is useful to receive an individual call.
Receive format is selectable "AND" or "OR" with QT/
DQT. The radio response of option signalling is program-
mable call Alert and "Transpond" for each option signalling
(2-Tone decode program 1, 2-Tone decode program 2, 2-
Tone decode program 3, DTMF).
4-3. PTT ID
PTT ID provides a DTMF ANI to be sent with every time
PTT (connect ID at beginning of transmission, disconnect ID
at end of transmission, or both).
You can program PTT ID "on" or "off" for each channel.
The contents of ID are programmed for each transceiver.
4-4. Busy Channel Lockout
Transmission is inhibited when the channel is busy. It is
able to set this feature "Yes" or "No" for each channel.
4-5. Scan Delete/Add
Scanning "delete/add" is programmable for each chan-
nel. Set the currently selected channel required to include in
the scan sequence to "add".
The operator can change the "delete/add" information
using the key programmed to "delete/add" function.
5. Key Functions
5-1. No Function
Sounds error operation beep, and no action will occur.
Use this function when the transceiver is required to be
more simple operated.
5-2. AUX.
The AUX function can be programmed for push key.
If this key is pressed, the "A" icon lights on the LCD and
the AUX port which is contained in 15-pin connector located
at the rear of the transceiver goes to low level.
If pressed again, the "A" icon goes off and the AUX port
goes to Open-collector.
5-3. Channel Down
If this key is pressed once, the channel number de-
creases by one step. If this key is hold down, the channel
number decreases continuously.
5-4. Channel Up
If this key is pressed once, the channel number increases
by one step. If this key is hold down, channel number in-
creases continuously.
5-5. Channel Name
This key switches the LCD display between the current
channel number and programmed channel name.
OPERATING FEATURES
5-6. Delete/Add
tween "Delete" and "Add".
"Delete" channel is not contained. In the scan mode, this
key switches the channel delete or add temporarily.
5-7. Home Channel
grammed home channel. Press this key again, the channel
goes back to the previous channel.
5-8. Monitor
key once, "MON" appears and unmutes speaker if a carrier
is present, regardless of the specified signalling (including
option signalling). Press this key again, "MON" disappears
and mutes speaker.
Option Signaling is reset. DBD (Dead Beat Disable) mode is
not reset by this operation.
the squelch.
5-9. Operator Selectable Tone
code/Decode QT/DQT is switched to the OST Tone pair. If
pressed again, the "OST" icon goes off and Encode/Decode
QT/DQT returns to KPG-59D pre-set.
enters "OST Select Mode". In this mode, the display
shows OST No. or OST Name which is set to the channel
and operator can select one of OST Tone pair using UP key
and DW key.
memorized to the channel, the transceiver exits from the
OST Select Mode, returns to normal channel display and
"OST" icon lights.
KPG-59D. OST is useful to access the repeater with same
radio frequency and different tone (QT/DQT).
5-10. Scan
scanning.
5-11. Squelch Level
Press the key programmed to "squelch level", the trans-
ceiver enters to "squelch level adjust mode".
key programmed to "squelch level" again, the adjusted
level is memorized and returns to the normal user mode.
5-12. Talk Around
quency and the tone for transmission.
repeater). Press this key again, the talk around function
goes off.
This key switches the currently displayed channel be-
The "Add" channel contained in the scan sequence, and
Press this key once, the channel switches to the pre-pro-
Monitor the channel before a transmission. Press this
Press this key after the Option Signalling is matched, the
Press and hold the Monitor key for 2 seconds to disable
When this key is pressed, the "OST" icon lights and En-
When this key is held down for 1 second, the transceiver
If pressed this key again, the displayed OST code is
16 kinds of tone pair for OST can be programmed by
Press this key starts scanning. Pressing this key stops
The preset squelch level is varied in user mode (0 to 15).
The squelch level can be adjusted by
Press this key, the transceiver uses the receive fre-
The operator can call the other party directory (without
TK-6110
/ . Press the
7