moon Evolution 700i Series Owner's Manual page 10

MOON 700i Dual-Mono Integrated Amplifier
Software Setup
13 The fourth configurable option is the volume bypass feature for use with home-theater processors and source
components that have their own volume control. When activated, the volume control of the 700i is bypassed and
the volume level is adjusted using the component connected to the input. Slowly rotate the volume control
clockwise and "BYPASS" will appear in the display. Press "OK".
14 The factory default of "BYPASS N" will appear in the display.
"BYPASS N" and "BYPASS Y" and then press "OK". Next you will be asked to confirm your selection as "SURE ? N"
will appear in the display. Rotate the volume control until "SURE ? Y" appears in the display. Press "OK" and
"SAVED" will briefly appear in the display followed by "BYPASS". When you set the volume bypass to "Y", the
volume setting you saved for the input with "OFFSET" will be maintained.
15 The fifth and final configurable option for the B1 input is to disable it in the event that it won't be used. Slowly
rotate the volume control clockwise and "ENABLE" will appear in the display. Press "OK".
16 The factory default is "ENABLE Y" which will appear in the display. Use the volume control to alternate between
"ENABLE N" and "ENABLE Y". Press "OK" and "SAVED" will briefly appear in the display followed by "ENABLE".
When an input has been disabled it will appear only in the Setup menu as "B1 N/A".
17 You have now passed through all five configuration options for the B1 input. At this point, you can (i) repeat the
above process for the another input by pressing the "Setup" button and then use the volume control to select the
next input to configure, (ii) exit from the Setup procedure by pressing the "Setup" button three times or (iii)
continue with the Setup procedure by assigning the 12 Volt trigger outputs, disabling the infrared remote sensor,
changing the IR codes, or resetting the 700i back to factory default status (see the following examples).
The MOON 700i is equipped with software that allows the MiND app to control various features of this preamplifier. With the
MiND app you will be able to adjust the volume level, mute the output, place the preamplifier into 'Standby' mode and then
place it back into operational mode. As well, when you begin playing a music track from the MiND app, the 700i will
automatically switch to the input configured for the MiND. With the MiND app, you are essentially controlling your entire
MOON system using a hand-held Apple (iPad, iPhone, iPod Touch,) or Android device.
You don't need to LABEL an input with "MiND" to achieve these aforementioned functions, but you must configure one input
for MiND functionality. An example for this scenario would be the
MOON 750D DAC /Transport
Only one of the five inputs may be configured for the MiND. "B1" is the default input. If, in the previous section, you already
assigned the "MiND" label to one of this preamplifier's inputs, then there's nothing required to do here – The corresponding
input has been automatically configured for MiND and cannot be changed until you change the input 'LABEL" assigments.
However, if you haven't assigned the "MiND" label to one of the 700i's inputs, the following example shows how to configure
an input for MiND functionality:
1 You may either continue where we left off in the previous example by pressing "Setup" twice to return to the main
menu and the turn the volume control until "MiND" appears in the display OR enter into the "Setup" mode from
the beginning by pressing the "Setup" button and rotating the volume control until "MiND" appears in the display.
2 Press "OK" and "MiND:B1" will appear in the display.
3 Rotate the volume control clockwise until the input you want to configure appears in the display.
4 Press "OK" and "SAVED" will appear brielfy in the display followed by "MiND".
5 Press the "Setup" button and "EXITING" will appear in the display.
____________________________________________________________________________________________________
Software Setup
(continued)
, which then outputs its analog signal to the MOON 700i.
Use the volume control to alternate between
MiND 180 D
streaming device feeding a digital signal to a
10