Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for moon 700i Evolution Series
Summary of Contents for moon 700i Evolution Series
- Page 1 Owner’s Manual Evolution Series 700i Reference Dual-Mono Integrated Amplifier...
-
Page 3: Important Safety Instructions
700i Reference Dual-Mono Integrated Amplifier Important Safety Instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves or another apparatus that produces heat. - Page 4 To prevent shock hazard, all three connections must ALWAYS be used. Connect the MOON 700i only to an AC source of the proper voltage; Both the shipping box and rear panel serial number label will indicate the correct voltage. Use of any other voltage will likely damage the unit and void the warranty AC extension cords are NOT recommended for use with this product.
-
Page 5: Table Of Contents
700i Reference Dual-Mono Integrated Amplifier Table of Contents Introduction ............. 6 Unpacking............7 Installation & Placement ........7 Front Panel Controls ........8 Software Setup ..........9 Rear Panel Connections ........15 SimLink™ ............16 Operating the 700i .........16 Remote Control Operation .......17 Troubleshooting .......... -
Page 6: Introduction
The performance of your Your MOON 700i dual-mono integrated amplifier incorporates many significant design features to achieve its “world-class” level of performance. This is an abbreviated list of the more important features: Proprietary “Lynx”... -
Page 7: Unpacking
700i from any potential damage during packaging, storing it in a safe, dry place in case transit Please write the serial number of your new MOON 700i in the space provided below for future reference. Serial No.: ________________ Installation & Placement... -
Page 8: Front Panel Controls
700i Reference Dual-Mono Integrated Amplifier Front Panel Controls Figure 1: Front panel of MOON 700i dual-mono Integrated Amplifier The front panel will look similar to Figure 1 (above). short period of time whenever you press any of the The large display window normally indicates the... -
Page 9: Software Setup
” buttons allow you to choose which clockwise to lower the volume, you are actually input source you wish to listen to. The MOON 700i engaging a precision optical encoder which selects dual-mono integrated amplifier has a total of five (5) very high quality metal-film resistors that the audio inputs;... - Page 10 “OK” and in alphabetical order (AUX … CD … TUNER, “SAVED” will briefly appear in the display etc.), various MOON source model names (i.e. followed by “MAX VOL”. The lowest possible ANDROMEDA … 750D, etc) and finally a choice setting is 40.0dB.
- Page 11 , which then outputs its this preamplifier. With the MiND app you will be able analog signal to the MOON 700i. Only one of the to adjust the volume level, mute the output, place five inputs may be configured for the MiND. “B1” is the preamplifier into ‘Standby’...
- Page 12 The MOON 700i is equipped with a 12 Volt trigger When you set the IR input to “Y”, all inputs output. When an input is assigned to the 12 Volt previously “Y”...
- Page 13 700i Reference Dual-Mono Integrated Amplifier If you want to control the MOON 700i using a with a universal remote control, you can disable the wired aftermarket infrared remote control receiver IR sensor located on the front panel as follows: 1. You may either continue where we left off in the 3.
- Page 14 700i Reference Dual-Mono Integrated Amplifier Reset the MOON 700i software settings back to their factory defaults: 1. You may either continue were we left off in the 4. Press “OK” and “SURE ? N” will appear in the previous example by turning the volume control display.
-
Page 15: Rear Panel Connections
700i Reference Dual-Mono Integrated Amplifier Rear Panel Connections Figure 2: Rear panel of MOON 700i Integrated Amplifier The rear panel of the MOON 700i dual-mono On the bottom row you will find one pair balanced integrated amplifier will look similar to Figure 2 XLR inputs labeled B1 with each channel’s input... -
Page 16: Simlink
750D’s brightness level will automatically adjust the If you are using your MOON 700i with an older brightness level of the 700i. MOON product such as a SuperNova, you will need to update the software of the older product to allow A third feature of SimLink™... -
Page 17: Remote Control Operation
The MOON 700i Dual-Mono Integrated Amplifier uses the ‘FRM-3’ full function, all aluminum backlit remote control (figure 3). It operates on the Philips RC-5 communication protocol and is can be used with other MOON components such as CD Players, DAC’s, Integrated Amplifiers, as well as other Preamplifiers. - Page 18 (3) seconds. The backlight will illuminate once, very briefly for confirmation. Remote operation with multiple MOON components Figure 4: Remote Operation with SimLink™ this system’s ZONE, the 180 MiND will turn on, as In figure 4 we have a 180 MiND Music Streamer will the 750D and 700i;...
-
Page 19: Troubleshooting
When you turn on the 700i via remote control (or its Standby button), the 870A will turn on automatically. The same rule applies when you put the 700i into Standby mode Troubleshooting Your MOON 700i is a “smart” integrated amplifier more) of your source components. You must equipped with a self-diagnostic system that will determine if there is any DC present. -
Page 20: Specifications
Pin 1 ......Ground Pin 2 ......Positive Pin 3 ......Negative NOTE: If you require the RS-232 codes for your MOON 700i, please contact Simaudio directly by email (service@simaudio.com) or toll-free telephone (877-980-2400). Fuse Replacement: For the 120V version use a 6A fast blow (3AG size).
Need help?
Do you have a question about the 700i Evolution Series and is the answer not in the manual?
Questions and answers