1. Manuals
  2. Brands
  3. moon Manuals
  4. Amplifier
  5. Evolution i-7
  6. Owner's manual

moon i-7 Owner's Manual

Evolution series dual-mono integrated amplifier
Hide thumbs Also See for i-7:
Table of Contents

Advertisement

Quick Links

Download this manual
Owner's Manual
MOON Evolution Series
i-7
Reference Dual-Mono Integrated Amplifier

Advertisement

Table of Contents
loading

Related Manuals for moon i-7

Summary of Contents for moon i-7

  • Page 1 Owner’s Manual MOON Evolution Series Reference Dual-Mono Integrated Amplifier...

  • Page 2: Important Safety Instructions

    MOON i-7 Dual-Mono Integrated Amplifier Important Safety Instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block ventilation openings. Install in accordance with the manufacturer’s instructions.
  • Page 3 To prevent shock hazard, all three connections must ALWAYS be used. Connect the MOON i-7 only to an AC source of the proper voltage; Both the shipping box and rear panel serial number label will indicate the correct voltage. Use of any other voltage will likely damage the unit and void the warranty AC extension cords are NOT recommended for use with this product.

  • Page 4: Table Of Contents

    MOON i-7 Dual-Mono Integrated Amplifier Table of Contents Congratulations ..........5 Unpacking............5 Introduction ............. 6 Installation & Placement ........6 Front Panel Controls ........7 Software Setup ..........8 Rear Panel Connections ........11 SimLink™ ............12 Operating the i-7 ...........12 Troubleshooting ..........

  • Page 5: Congratulations

    Your new Integrated Amplifier is a true dual-mono design, whereby each channel operates completely independent of the other. The performance of your i-7 will continue to improve during the first 400 hours of listening. This is the result of a “break-in”...

  • Page 6: Introduction

    In the event that the surface you have chosen isn’t perfectly level, each of the four (4) legs of your i-7 are height adjustable; carefully using your fingers, you can either raise each leg by turning the cone underneath clockwise, or lower each leg by turning it counterclockwise.

  • Page 7: Front Panel Controls

    2) engage the effects of the signal processor. The monitor component’s outputs must be connected to the i-7’s “Tape Monitor In” and its inputs must be connected to the i-7’s “Tape Monitor Out”.

  • Page 8: Software Setup

    Note: To change the balance between the left and right channels, please refer to the section “Remote Control Operation”. The “Input +” and “Input -” buttons allow you to choose which input source you wish to listen to. The MOON i-7 dual-mono integrated amplifier has a total of five (5) inputs;...
  • Page 9 (ii) exit from the Setup procedure by pressing the “Setup” button three times or (iii) continue with the Setup procedure and either assign the 12 Volt trigger outputs or reset the i-7 back to factory default status (see the following examples).
  • Page 10 (continued) The MOON i-7 is equipped with a 12 Volt trigger output. When an input is assigned to the 12 Volt trigger, the device connected to the trigger will automatically start-up whenever you switch to that input. The default setting for all five inputs is on.

  • Page 11: Rear Panel Connections

    Beside each of these XLR inputs is a single-ended tape monitor loop; both the input and output connectors for each channel are located on their respective sides of the rear panel. The i-7 also has a line-level preamplifier output that allows you to use this integrated amplifier as a preamplifier ONLY, for use with a separate power amplifier.

  • Page 12: Simlink

    In the event that you plan to be away from your home for a few days, powering off the integrated amplifier may not be a bad idea. Once fully “broken-in”, please keep in mind that your i-7 will require several hours of playing time before it reaches its peak performance after you’ve powered it up again.

  • Page 13: Troubleshooting

    DC is present, the front panel display will show “DC LEVEL”; when overheating “HIGHTEMP” will appear in the display. If your i-7 powers itself off or will not power up, there may very well be DC present in one (or more) of the inputs coming from one (or more) of your source components.

  • Page 14: Remote Control Operation

    Allen key to remove the three screws located on the back plate; insert the batteries in the correct direction and then screw the back plate back into place. To operate the i-7 with this remote control, you must first press the button labeled ‘Preamp’ in the top right corner.

  • Page 15: Specifications

    Pin 1........ Ground Pin 2........ Positive Pin 3 ......Negative NOTE: In the event that you require the RS-232 codes for your MOON i-7, please contact Simaudio Ltd. directly by either email (service@simaudio.com) or by toll-free telephone (877-980-2400). Fuse Replacement: For the 120V version use a 6A fast blow (3AG size).

Table of Contents