Table of Contents
Advertisement
NTI VOPEX-USBV-2 KVM SPLITTER
The following functions exist while in Command Mode:
Key Combination
<X>-<key>-<Y>
<L> - <x> - <x>
<V> - <Enter>
<M>
<W>
<D> - <x>
<P> - <x>
<Esc>
Mice and Trackballs with MACs
The VOPEX can be configured to enable full functionality between mice and trackballs having two or more buttons and a USB
MAC CPU. By default, the CPU port on the VOPEX is configured for use with a WINDOWS or SUN CPU and has no special
translation for using multi-function mice and trackballs when a MAC CPU is connected. Using the commands in Command Mode
above, either enable or disable this feature as needed.
NOTE: Be sure to re-configure the port for connection to a WINDOWS or SUN CPU if a MAC CPU is removed and a
WINDOWS or SUN CPU is then connected.
International SUN Keyboards
The VOPEX can recognize international layouts for Sun keyboards. To use an international Sun keyboard, follow this procedure:
1. Disconnect the CPU from the VOPEX
2. Connect the international keyboard to be used to the VOPEX
3. Power down the VOPEX for at least 3 seconds
4. Power up the VOPEX
5. Reconnect the CPU to the VOPEX
It is also possible to configure the VOPEX to emulate a specific international Sun keyboard regardless of what actual keyboard is
connected. This is recommended when the CPU needs the layout code (i.e. a SUN CPU) and the keyboard doesn't have an
explicit layout code (i.e. some Windows keyboards). To do this, manually set the VOPEX to indicate the international keyboard
identification number to the CPU using the following procedure:
1. Connect the keyboard to be used to the VOPEX
2. Power down the VOPEX for at least 3 seconds
3. Power up the VOPEX
4. Enter Command Mode (<Ctrl> - <`>)
5. Type Lxx, where xx is the number from the list below that corresponds to the desired country code
6. Exit Command Mode
7. Power down the VOPEX for at least 3 seconds
8. Power up the VOPEX
9. Reboot the CPU connected to the VOPEX
Country Codes
00
Not Supported
01
Arabic
02
Belgian
03
Canadian-Bilingual
04
Canadian-French
05
Czech Republic
06
Danish
07
Finnish
08
French
09
German
Description of Function
Select a new key sequence to use to enter Command Mode – Replace <key> with the desired key
to follow <Ctrl> with.
Select the country code of the keyboard being used with a USB SUN CPU (see Country Codes
chart on page 6)
This will print the version of the code in the VOPEX to a text editor window (i.e. Windows Notepad)
for use when troubleshooting the VOPEX. Note: The text editor should be open prior to entering
Command Mode.
Configure the CPU port to connect to a MAC CPU (see "Mice and Trackballs with MACs" on pg. 6.
Configure the CPU port to connect to a Windows or SUN CPU
Select the operating mode, x=1 for Instantaneous Mode, x=2 for Delay Mode, x=3 User 1 Mode, x=4
for User 2 mode, x=5 for User 3 mode, x=6 for User 4 mode. (Modes are described in the table on
page 5.)
Select the default mode to have the VOPEX enter upon power-up.
Exit Command Mode
10
Greek
11
Hebrew
12
Hungary
13
International (ISO)
14
Italian
15
Japan (Katakana)
16
Korean
17
Latin American
18
Netherlands/Dutch
19
Norwegian
20
Persian (Farsi)
30
21
Poland
31
22
Portuguese
32
23
Russia
33
24
Slovakia
34
25
Spanish
35-99
26
Swedish
27
Swiss/French
28
Swiss/German
29
Switzerland
6
Taiwan
Turkish
UK
US
Yugoslavia
Reserved
Advertisement
Table of Contents
