Hitachi J300U Series Instruction Manual page 141

Function mode
Electronic thermal characteristics
free setting (frequency 2)
Electronic thermal characteristics
free setting (current value 3)
Electronic thermal characteristics
free setting (frequency 3)
Overload limit level setting
Overload limit constant setting
Overload limit selection during
acceleration
Frequency lower limiter setting
Frequency upper limiter setting
Jump frequency (1)
Jump frequency (2)
Jump frequency (3)
Jump frequency width setting
Allowable instantaneous time
Reclosing stand-by after instantaneous
power failure recovered
Instantaneous power failure restart
selection
Trip selection during stop at under
voltage
Max. frequency selection
Software lock selection
STOP key validity selection
Running direction selection
Reverse run prevention
Reduced voltage soft start setting
Analog input voltage selection
External frequency start setting
External frequency end setting
External frequency start rate setting
External frequency end rate setting
External frequency start point setting
Frequency command sampling
frequency setting
Arrival signal output pattern selection
Arrival frequency setting for acceleration
Arrival frequency setting for deceleration
Overtorque signal rate for plus torque
Overtorque signal rate for minus torque
Display with HOP, HRW Display with DOP, DRW
Layer Data display
3-5-1 6 F2 0 Hz F-23
7 A3 24.0 A
8 F3 73 Hz
3-5-2 1 LEVEL 125% F-24
2 CONST 1.0
3 ACC 1: ON
3-5-3 1 LIML 0.0 Hz F-26
2 LIMH 0.0 Hz
3 F1 0.0 Hz F-27
4 F2 0.0 Hz
5 F3 0.0 Hz
6 WIDTH 0.5 Hz
3-5-4 1 TIME 1.0 s F-22
2 WAIT 1.0 s
3 POWR 0: ALM
4 TRIP 1: OFF
3-5-5 1 MAXF 0: 120 Hz F-30
2 SLOCK 1: MD1 F-25
3 STOP 1: ON F-28
4 F/R 2: FRE F-29
5 PREV 0: OFF
6 RVS 6
3-6-1 1 V 1: 10 F-31
2 EXS 0.0 Hz
3 EXE 0.0 Hz
4 EX%s 0 %
5 EX%E 100 %
6 LEVEL 0 Hz
7 F-SAMP 8
3-6-2 1 PTN 0: CST F-32
2 ACC 0.0 Hz
3 DEC 0.0 Hz
4 V 100 % F-33
5 R 100 %
Function No. with digital operator
No. Data display Alterability No.
E-THM F2 0000 Hz
E-THM A3 24.0 A
E-THM F3 0073 Hz
OLOAD LEVEL 125%
OLOAD CONST 01.0
OLOAD ACC ON
LIMIT L 0000.0 Hz
LIMIT H 0000.0 Hz
JUMP F1 0000.0 Hz
JUMP F2 0000.0 Hz
JUMP F3 0000.0 Hz
JUMP W 0.5Hz
IPS TIME 1.0 s
IPS WAIT 001.0 s
IPS POWR ALM
IPS TRIP OFF
F-MAX-L 120 Hz
S-LOCK MD1
STOP-SW ON
F/R SW FRE
F/R PREV OFF
F/R RVS 6
IN ANA 10V
IN EXS 0000.0 Hz
IN EXE 0000.0 Hz
IN EX%S 000 %
IN EX%E 100 %
IN LEVEL 0 Hz
IN F-SAMP 8
ARV PTN CST
ARV ACC 0.0 Hz
ARV DEC 0.0 Hz
0V-TRQ V 100 %
0V-TRQ R 100 %
A-29
Data read/copy
Data HRW DRW
N — — Y
N — — Y
N — — Y
N — — Y
N — — Y
N — — Y
Y A5 0.0 Y
Y A6 0.0 Y
Y A7 0.0 Y
Y A8 0.0 Y
Y A9 0.0 Y
N — — Y
N — — Y
N — — Y
Y A34 0 Y
N — — Y
Y A64 120 Y
N — — Y
N — — Y
N — — Y
N — — Y
Y A58 6 Y
Y A48 1 Y
Y A26 0.0 Y
Y A27 0.0 Y
N — — Y
N — — Y
N — — Y
Y A11 8 Y
Y A49 0 Y
Y A39 0 Y
Y A40 0 Y
N — — Y
N — — Y
set
value
N
N
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
N
N
N
Y
N
Y
Y
Y
N
N