Peco Performance Pro T12000 Series Installation Manual page 4

Part vIII: moUnt the t12000 onto the wallPlate
1. Position the thermostat slightly above the mounted wallplate (see Fig. 9), then secure
the hooks on the back side of the thermostat to the hinge pockets on the wallplate.
note: the top back side of the thermostat should slip into the hinge pockets
easily. Do not use excessive force.
2. Align the pins on the back side of the thermostat with the terminal blocks on the
wallplate.
Figure 9.
Secure the hooks
on the back side of
the thermostat to the
wallplate.
3. Gently bring down the thermostat onto the wallplate so the pins on the back of the
thermostat fi t into the terminal blocks on the wallplate (see Fig. 10).
4. Attach the retaining screw to the underside of the thermostat as shown (see Fig. 10).
Figure 10.
Mount the thermostat
so pins on back fi t into
the terminal blocks on
the wallplate.
Retaining screw
Part IX: verIFY thermostat oPeratIon wIth sYstem tests
System test verifi cation is highly recommended to verify thermostat operation. Follow at
least one procedure in the system tests below. Refer to the Service Menus (see Table 2)
for more system tests. For all system tests, press cool ▲/ ▼to advance to the following
system test, which is the next available Service Menu. Press ▲/ ▼to select an option
in Service Menu. Press Done only if fi nished performing all system tests. Pressing Done
exits the Service Menus and turns off all active outputs.
sYstem test maIn oUtPUt (heat)
1. On the thermostat, press the lower left and lower right area simultaneously for about
fi ve seconds. Service Menu number, fl ashing default value, ▲/ ▼arrows, and
appear.
Done
2. Press cool ▲/ ▼until Service Menu 610 appears in the display (see Fig. 11).
(Default value "00" appears below Service Menu.)
Figure 11.
Service Menu 610
allows user to
perform System
Test (Heat).
© COPYRIGHT 2010 PECO, INC. ALL RIGHTS RESERVED.
3. In Service Menu 610, press ▲/ ▼to select option "01," Heat Stage 1
(see Fig. 12). note: If 01 is selected, the thermostat will activate the associated
output for up to 10 minutes. The user should observe that the fan output (with heat)
turns on. The user may also test more stages of heat according to what is available
for the system type.
4. Press
Done
the system test, the outputs are disabled and the fan will stop.
optional: the user may perform additional system tests by pressing
cool ▲/ ▼ to access more service menus (see note below).
sYstem test Fan (oPtIonal)
The following instructions assume that the user enters the Service Menus from the Home
Display; it does not assume that the user has followed in sequence from the previous
section. If continuing from the previous section on this page, skip to Step 2 below.
1. On the touchscreen display, press the lower left and lower right areas
simultaneously for about fi ve seconds. note: Service Menu number, fl ashing default
value, ▲/ ▼arrows, and
2. Press cool ▲/ ▼ until Service Menu 620 appears in the display (see Fig. 13).
(The default value "00" for appears below Service Menu.)
3. In Service Menu 620, press ▲/ ▼to select option "01" to enable fan output (see
Fig.14). note: If 01 is selected, the thermostat will activate the associated output for
up to 10 minutes. The user should observe that the fan output will turn on.
Press
Cool ▲
to advance
Service Menus
Default value
(appears
automatically)
4. Press
Done
are disabled.
optional: the user may perform additional system tests by pressing cool ▲/
▼. additional system tests include (see table 2): 600, system test main output
(cool); 630, system test emergency output; 640, system test economizer.
4
to complete the system test and exit the Service Menus. After verifying
appear.
Done
to complete the system test. After verifying the system tests, the outputs
P/N 70480 3220-2269 REV 00
Figure 12.
Press Done to
complete test and
exit Service Menus
or Next to continue
to the next test.
Figure 13.
Service Menu 620
allows user to
perform a System
Test Fan.
Press
Cool ▲
to advance
Service Menus
Default value
(appears
automatically)
Figure 14 .
Press Done to
complete testing
and exit Service
Menus, or Next to
continue tests.