Peco Performance pro T12000 Quick Start Manual

AN ASTRONICS COMPANY
1
SeT clocK, Year, MonTH, daY
1. Press ▲/ ▼ to select 12 or 24 Hr mode, then
press
Clock.
2. Press ▲/ ▼to select hour, then press Clock.
3. Press ▲/ ▼to select minutes, then press Clock.
4. Press ▲/ ▼ to select year, then press Clock.
5. Press ▲/ ▼ to select month, press Clock.
6. Press ▲/ ▼ to select the calendar day number.
7. Press to complete operation.
Done
2
acceSS Service MenuS
Insulator
Tab
1. Press touchscreen, lower left and lower right,
for about fi ve seconds to access Service Menus.
2. Press cool ▲/ ▼ button to select Service Menu.
3. next, press ▲/ ▼ to select (fl ashing) option in
Service Menu.
4. repeat steps 2, 3, to complete confi guration.
5. Press done when complete.
Note: Upon completion of installation, remove
the plastic insulator tab from the back side of the
thermostat.
© COPYRIGHT 2014 PECO ASTRONICS. ALL RIGHTS RESERVED.
PERFORMANCE PRO T12000
3
configure Service MenuS
The following Service Menus (SM) commonly require
confi guration. Please verify that these are set for your
specifi c application. additional confi guration may be
required. refer to Table 2 for all available Service Menus.
• SM 100 = Schedule format and Programmable or
nonprogrammable
• SM 110 = System Type
• SM 120 = fan control
• SM 130 = changeover (reversing) valve
• SM 240 = number of Program Periods
• SM 260 = Temperature format (°f or °c)
• SM 340 = Keypad lockout
4
Wiring: TerMinal deSignaTionS
1. connect wires for appropriate system type
(Table 1).
▲
!
WARNING: DISCONNECT POWER BEFORE BEGINNING INSTALLATION.
• CAUTION: Use copper wire only. Insulate or wire-nut all unused leads.
• Use care to avoid electrostatic discharge to thermostat
• CAUTION: Do not connect unused wires together
• ALL ELECTRICAL LOADS MUST BE CONNECTED TO TERMINAL C
(24 VAC).
Table 1. TerMinal blocK deSignaTionS
Fan Coil (Conventional)
C 24 VAC, Unswitched side
Service
W1 Stage 1 Heat
Menu
Current
W2 Stage 2 Heat
option
G FAN
A Economizer/Damper/Humidity A
E Stage 3 Heat
Y1 Stage 1 Cool
Y2 Stage 2 Cool (or Dehumidify)
24 VAC Power for heating,
RH
switched side
24 VAC Power for cooling,
RC
switched side
SC Sensor Common
S1 Indoor Remote Sensor
S2 Occupancy Setback Input*
S3 Outdoor Remote Sensor
*Contact PECO to learn more about Occupancy Setback
Input sensor applications.
1

QUICK START GUIDE

Heat Pump
C 24 VAC, Unswitched side
B/O Reversing Valve
AUX Auxiliary Heat (Stage 3)
G FAN
Economizer/Damper/Humidity
E Emergency Heat
Y1 Compressor Stage 1/Heat/Cool 1
Compressor Stage 2/Heat/Cool 2
Y2
(or Dehumidify)
24 VAC Power for heating,
RH
switched side
24 VAC Power for cooling,
RC
switched side
SC Sensor Common
S1 Indoor Remote Sensor
S2 Occupancy Setback Input*
S3 Outdoor Remote Sensor
P/N 70932 3220-2324 REV 00