LG 55WV70 Setup Manual page 26

Installer Menu (Cont.)
092 - HDMI3 ENABLE
Set to 1 to enable HDMI 3 input in DTV Mode. Set to 2 to enable
HDMI 3 input in PC Mode. Set to 0 to disable display panel HDMI
3 input.
093 - RJP AVAILABLE (Remote Jack Pack Available)
•
0 = Remote jack pack is not available or disabled.
•
1 = Legacy Model RJPs: HDMI Mode
Enables RJP feature for use with full cable bundle models. In
this mode, when an HDMI source is connected to the RJP, both
digital video and audio are expected via the HDMI cable. If no
digital audio is present, no audio will be heard.
•
2 = Legacy Model RJPs: DVI Mode
Enables RJP feature for use with full cable bundle models. In
this mode, when an HDMI/DVI source is connected to the RJP,
only digital video is expected via the HDMI cable. Analog audio
is provided via a separate cable, from the source, connected to
an RJP AUDIO IN. If no analog audio cable is connected, tuner
audio will be heard.
•
5 = Scaler Model RJPs: HDMI Mode
Enables RJP feature for use with reduced cable bundle models.
In this mode, when an HDMI source is connected to the RJP,
both digital video and audio are expected via the HDMI cable. If
no digital audio is present, no audio will be heard.
•
6 = Scaler Model RJPs: DVI Mode
Enables RJP feature for use with reduced cable bundle models.
In this mode, when an HDMI/DVI source is connected to the
RJP, only digital video is expected via the HDMI cable. Analog
audio is provided via separate cable, from the source, connect-
ed to an RJP AUDIO IN. If no analog audio cable is connected,
tuner audio will be heard.
Note: See also Reference section, "RJP Model List & Input Auto-
sensing Hierarchy." Settings 1, 2, 5, and 6 allow the lodge staff to
customize each TV's RJP setup based on customer requirements.
Note: When this item is enabled in the Installer Menu, item 042
AUTO INPUTS is automatically set to 0.
094 - SAP MENU EN (2nd Audio Program)
Set to 1 to enable SAP feature on Function Menu, if Function
Menu is available (i.e., TV is not in Pass-through Mode). Set to
0 to disable SAP feature on Function Menu, if Function Menu is
available.
096 - DEF. ASP. RATIO (Default Aspect Ratio)
Selects default aspect ratio at power up.
•
Set to 0 for Set By System.
•
Set to 1 for 4:3.
•
Set to 2 for 16:9 (Factory Default).
•
Set to 3 for Just Scan.
•
Set to 4 for Zoom.
Note: This item is not available in the Installer Menu unless item
106 ASP RATIO LOCK is set to 0.
26
097 - AUDIO OUTPUT
Determines availability and signal type/level (fixed speaker,
variable speaker, or fixed line level [amplifier]) of the audio output
to be used by external audio equipment connected to the Speaker
Out jack on the TV. Set to 0 to disable audio output. Otherwise,
see the table below and set as required in accordance with audio
equipment.
Value
0
Speaker Output 1
2
3
4
5
6
7
8
Line Output 9
See also Reference section, "Stereo Speaker Setup," for further
information.
098 - PRO:CENTRIC
Selects the Pro:Centric Application Mode. Set to 0 (default) to
disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2
for GEM (Java Application) Mode.
The TV must be turned OFF for a few seconds to initiate the
Pro:Centric application download. When it is turned OFF for a
second time, the TV will load the Pro:Centric application.
Note: This item is not available in the Installer Menu when item
119 DATA CHANNEL is set to 0.
099 - BACK LIGHTING
Sets the TV screen brightness at power up. Default setting is 255.
•
1 - 100 Static Back Lighting
(1 = Dimmest picture, 100 = Brightest picture)
•
101 - 200 Dynamic Back Lighting
(101 = Dimmest picture, 200 = Brightest picture)
If set between 101 and 200, the TV automatically controls back
lighting depending upon the picture level of the current program. If
set to 255, back lighting is controlled via the Picture settings in the
TV's setup menus.
102 - ATSC BAND
Sets up TV to receive different types of incoming signals:
0 = Broadcast, 1 = CATV, 2 = HRC, 3 = IRC, 4 = Same as NTSC.
103 - ATSC TUNE MODE
Sets ATSC tuning mode. Default set to 1 for Physical Channel
scan. Set to 0 for Virtual Channel scan.
Status
Disabled
Fixed 0.01 Watts
Fixed 0.03 Watts
Fixed 0.05 Watts
Fixed 0.10 Watts
Fixed 0.20 Watts
Fixed 0.50 Watts
Fixed 1.00 Watt (default)
Control with volume
Fixed line level (typically 400 mVrms ±
100 mVrms @10KΩ) output
206-4231