Related Manuals for Clarke Contactor CON1200
Summary of Contents for Clarke Contactor CON1200
- Page 1 1200W HAMMER DRILL Model No. CON1200 PART NO: 6479505 OPERATING & MAINTENANCE INSTRUCTIONS GC0611...
-
Page 2: Introduction
INTRODUCTION Thank you for purchasing this CLARKE Hammer Drill. Before attempting to use the machine, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. -
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION .................. 2 GUARANTEE ..................2 ENVIRONMENTAL PROTECTION ............2 TABLE OF CONTENTS ................3 GENERAL SAFETY RULES ..............4 HAMMER DRILL SAFETY INSTRUCTIONS ..........6 ELECTRICAL CONNECTIONS .............. 7 OVERVIEW ..................8 OPERATION ..................9 MAINTENANCE ................... 11 FAULT FINDING ................... -
Page 4: General Safety Rules
GENERAL SAFETY RULES WORK AREA 1. Keep the work area clean and well lit. Cluttered and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids, gasses or dust. Power tools create sparks which may ignite dust or fumes. - Page 5 5. Dress properly. Do not wear loose clothing or jewellery which may get caught in moving parts. Wear protective hair covering to contain long hair. For best footing, wear rubber soled footwear. Keep floor clear of oil, scrap wood, etc. 6.
-
Page 6: Hammer Drill Safety Instructions
2. Using the correct bit. Use the appropriate drill bit for the material being drilled. Different bits are available from your Clarke dealer. 3. Use of the mains cable. Keep the mains cable well away from the drill and ensure an adequate electrical supply is close at hand so that the operation is not restricted by the length of the cable. -
Page 7: Electrical Connections
ELECTRICAL CONNECTIONS WARNING! Read these electrical safety instructions thoroughly before connecting the product to the mains supply. Before switching the product on, make sure that the voltage of your electric- ity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. -
Page 8: Overview
OVERVIEW The CLARKE CON1200 is a variable-speed drill, equipped with an adjustable speed controller, high and low gear selection and hammer operation and has a lock-on button for continuous operation. The drill is supplied with a depth stop rod and auxiliary handle. -
Page 9: Operation
OPERATION IMPORTANT: To avoid accidental starting, ensure the drill is switched OFF before plugging in to the mains. To do this, briefly pull the switch, and release to ensure the trigger lock is not set in the ‘lock’ position. INSERTING A DRILL BIT 1. - Page 10 FORWARD / REVERSE SELECTION 1. Set the forward/reverse selector switch to the position marked ‘R’ for normal ‘Right hand’ rotation. 2. Set the forward/reverse selector switch to the right hand position marked ‘L’ for ‘Left hand’ rotation. NOTE: This should only be performed when the drill is at a complete stop.
-
Page 11: Maintenance
• All bearings etc, in this tool are lubricated with a sufficient amount of high grade lubricant for the tools lifetime under normal operating conditions, therefore no further lubrication is necessary. • Refer to your CLARKE dealer if internal maintenance is required. Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 12: Fault Finding
ACCESSORIES & CONSUMABLE SPARES An extensive selection of accessories including Drill Bit Sets, Socket & Bit Sets and Drill Bit Sharpeners are available from your CLARKE dealer. Refer to your Clarke dealer or service department if internal maintenance is required. -
Page 13: Specification
& Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 14: Spare Parts
PARTS DIAGRAM Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 15: Parts List
PARTS LIST - f l l l u - f l Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 16 PARTS LIST Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 17: Vibration Emissions
‘K’, which represents the uncertainty factor, i.e. a value in excess of ‘a’, to which the tool could vibrate under normal conditions. These values appear in the specification panel below. MODEL No: CON1200 DESCRIPTION: 1200W HAMMER DRILL Declared vibration emission value in accordance with EN12096 Measured vibration emission value - a: 16.7m/s... - Page 18 You will note that a third value is given in the specification - the highest measured reading in a single plane. This is the maximum level of vibration measured during testing in one of the axes, and this should also be taken into account when making a risk assessment.
-
Page 19: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the Contactor CON1200 and is the answer not in the manual?
Questions and answers
Do you sell the trigger assembly WGCHD12055 for the con1200 hammer drill.
Yes, Clarke sells the trigger assembly WGCHD12055 for the CON1200 hammer drill.
This answer is automatically generated