Clarke CAT60 Operating & Maintenance Instructions

Clarke CAT60 Operating & Maintenance Instructions

1/2”reversible air drill

Advertisement

Quick Links

1/2"REVERSIBLE AIR DRILL
MODEL NO: CAT60
PART NO: 3110460
OPERATING & MAINTENANCE
INSTRUCTIONS
GC0614

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CAT60 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Clarke CAT60

  • Page 1 1/2”REVERSIBLE AIR DRILL MODEL NO: CAT60 PART NO: 3110460 OPERATING & MAINTENANCE INSTRUCTIONS GC0614...
  • Page 2 INTRODUCTION Thank you for purchasing this CLARKE Reversible Air Drill. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.
  • Page 3: General Safety Rules

    GENERAL SAFETY RULES CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY. WORK ENVIRONMENT 1. Keep the work area clean and tidy. 2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair out of the way.
  • Page 4 • The drill will be left unattended. • Moving to another work area. • Passing the drill to another person. 14. Never use the tool if it is defective or operating abnormally. 15. The drill should be serviced at regular intervals by qualified service personnel.
  • Page 5 OVERVIEW NO DESCRIPTION NO DESCRIPTION Chuck 1/4” BSP female air inlet Auxiliary Handle Forward/Reverse Switch Trigger Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
  • Page 6: The Compressed Air Supply

    THE COMPRESSED AIR SUPPLY AIR SUPPLY REQUIREMENTS WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF COMPRESSORS AND COMPRESSED AIR SUPPLY. • Use only clean, dry, regulated compressed air as a power source. •...
  • Page 7: Before Use

    Air-line Oil available from your CLARKE dealer. Replace the screw before using the tool. 2. If a mini-oiler is not being used, run a few drops of oil through the tool before use.
  • Page 8: Fitting The Handle

    FITTING THE HANDLE The CAT60 is supplied with an auxiliary handle. To install it proceed as follows. 1. Slide the clamping ring over the body of the drill., ensuring it rests on the flat shoulder provided. 2. Screw the handle onto the threaded part of the clamping ring until the handle assembly is tight.
  • Page 9: Key For Chuck

    1. Before use, drain water from the compressed air supply. 2. Pour a few drops of CLARKE airline oil, into the air inlet. This should be carried out regardless of whether or not an in-line mini oiler is used. If an...
  • Page 10 If the tool is to be stored, or is idle for longer than 24 hours, run a few drops of Clarke air line oil into the air inlet, and run the tool for 5 seconds in order to lubricate the internal parts.
  • Page 11: Troubleshooting

    2. Motor parts worn. 2. Return to Clarke dealer for repair. 3. Worn or sticking 3. Drip air tool lubricating mechanism due to oil into air inlet. Allow oil lack of lubricant.
  • Page 12: Parts Diagram

    PARTS DIAGRAM Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
  • Page 13: Parts List

    PARTS LIST Description No Description Drill Chuck Housing Set Screw Screw Trigger Ball Bearing 6201-Z00A Spring Washer Throttle Valve Spacer O-Ring Screw Reverse Valve Planet Carrier O-Ring Planet Gear Reverse Valve Bush Internal Gear O-Ring Spacer Ball Bearing 6200-ZZ0A Motor Housing Planet Carrier Planet Gear with Bush Exhaust Diffuser...
  • Page 14: Specification

    1.8 kg Please note that the details and specifications contained herein are correct at the time of going to print. However CLARKE International reserve the right to change specifications at any time without prior notice. Always consult the machine’s data plate.
  • Page 15: Declaration Of Conformity

    DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...

This manual is also suitable for:

3110460

Table of Contents