Table of Contents
Advertisement
12" Compound Slide
Set up and operating inStruCtionS
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
SaVe thiS manual.
©
Copyright
2008 by Harbor Freight Tools
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due
to continuing improvements, actual product may differ slightly from the product described herein.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised Manual 08h, 09j, 09k
miter Saw
model
98194
®
. All rights reserved. No portion of this manual or any
Advertisement
Table of Contents
Related Manuals for Chicago Electric 98194
Summary of Contents for Chicago Electric 98194
- Page 1 Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein.
-
Page 2: Table Of Contents
...11 adjuSting the beVel angle ... 12 uSing the depth Stop ... 12 making a Cut ... 12 SKU 98194 For technical questions, please call 1-800-444-3353. maintenanCe and SerViCing ...14 Cleaning, maintenanCe, and lubriCation ... 14 replaCing the blade ... -
Page 3: Important Safety Information
SKU 98194 For technical questions, please call 1-800-444-3353. notiCe is used to address practices not related to personal injury. Caution, without the... -
Page 4: Use Proper Extension Cord
Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. SeCure work. Use clamps or a vise to hold work when practical. It’s safer SKU 98194 For technical questions, please call 1-800-444-3353. length 100’ 150’ do not use. -
Page 5: Miter Saw Safety Warnings
Maintain labels and nameplates on the tool. These carry important safety information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Avoid unintentional starting. Prepare to begin work before turning on the tool. People with pacemakers should consult their physician(s) before use. -
Page 6: Grounding Instructions
This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The SKU 98194 For technical questions, please call 1-800-444-3353. plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. -
Page 7: Vibration Safety
Use tools with the lowest vibration when there is a choice between different processes. SKU 98194 For technical questions, please call 1-800-444-3353. Include vibration-free periods each day of work. Grip tool as lightly as possible (while still keeping safe control of it). -
Page 8: Components
Cover blade guard Center Cover dust Collection work piece Support extension hold down Vise base SKU 98194 For technical questions, please call 1-800-444-3353. ComponentS bevel angle indicator table miter handle kerf board Figure 1 handle trigger blade blade guard... -
Page 9: Specifications
Compound Sliding Miter Saw 12” Carbide Tipped Blade Table Extensions Dust Collection Bag Wrench reV 08k, 09a, 09j SKU 98194 For technical questions, please call 1-800-444-3353. initial Set up inStruCtionS read the entire important SaFetY inFormation section at the beginning of this manual... -
Page 10: Operating Instructions
(not included). This will help prevent tipping or movement of the saw, preventing injury. Also, the use of a saw table will make it easier to efficiently handle work materials and make more accurate cuts. Calibration after Shipping... -
Page 11: Using The Work Piece Extension Supports
Always support the work piece to be level with the table, and so that after the cut is made the cut off pieces will not fall. You may need to use saw horses or other supports (not included) to support the work piece. -
Page 12: Adjusting The Bevel Angle
To set the bevel angle, loosen the Bevel Lock Handle at the rear of the saw. (See Figure 2.) To do this, press in the Lock Button and rotate the Handle 1/2 turn counterclockwise. - Page 13 Turn the Laser guide on, using the switch on the side of the laser battery housing. Align the marked location of the cut on the work material with the saw blade. Be aware that the Saw Blade will remove material from the cut equal to the width of the blade.
-
Page 14: Maintenance And Servicing
From tool Failure: do not use damaged equipment. if abnormal noise or vibration occurs, have the problem corrected before further use. SKU 98194 For technical questions, please call 1-800-444-3353. Cleaning and maintenance beFore eaCh uSe, general condition of the tool. Check for... -
Page 15: Replacing The Blade
(See Figure 3.) Figure 4 Remove the Shoulder Screw (15). (See Figure 4 and photo below.) reV 09j SKU 98194 For technical questions, please call 1-800-444-3353. Shoulder Screw Figure 5 Raise the Blade Guard and Center Cover. (See Figure 5.) -
Page 16: Adjusting The Fence
Center Cover Fixing Bolt using the Wrench by turning it clockwise. Release the Locking Pin. reV 08k SKU 98194 For technical questions, please call 1-800-444-3353. adjusting the Fence The Fence holds the work piece in a fixed position while the Table and or the blade assembly are adjusted in a miter or bevel angle. -
Page 17: Adjusting The Miter Table Indicator
If the cut is not exactly vertical, the two pieces will form a slight angle. reV 09j SKU 98194 For technical questions, please call 1-800-444-3353. 45° bevel Stop and lock nut... -
Page 18: Cleaning And Lubricating The Miter Saw
Occasionally lubricate the pivot point of the Table as well as other moving parts with a dry lubricant, such as graphite. reV 09j SKU 98194 For technical questions, please call 1-800-444-3353. Page 18... -
Page 19: Troubleshooting
TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISINg OUT OF HIS OR HER REPAIRS TO THE ORIgINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISINg OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 98194 For technical questions, please call 1-800-444-3353. troubleshooting likely Solutions Check power at outlet. -
Page 20: Parts List
Angle Ruler Bolt Washer Pointer Washer Screw Wrench Lock Pin Spring Bolt reV 08k, 09c, 09j SKU 98194 For technical questions, please call 1-800-444-3353. partS liSt part description Washer Lock Nut M12 Bolt M5x12 Spring Washer Flat washer Oil Cover... - Page 21 Circle Block Bolt ST5x65 Stator Bolt M6x55 Brush Holder Carbon Brush Brush Cover Trigger Trigger Mount Bolt SKU 98194 For technical questions, please call 1-800-444-3353. partS liSt (Continued) part description Handle Mount Bolt ST6x25 Nut M5 Bolt M5x35 Upper Handle Bolt ST4.2x14...
-
Page 22: Assembly Diagrams
08k SKU 98194 For technical questions, please call 1-800-444-3353. Page 22... -
Page 23: Assembly Diagram
If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. reV 09c SKU 98194 For technical questions, please call 1-800-444-3353. Page 23... -
Page 24: Limited 90 Day Warranty
90 daY warrantY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
Need help?
Do you have a question about the 98194 and is the answer not in the manual?
Questions and answers
Need a trigger (switch)for Chicago Electric 12" Sliding Saw #98194. The parts diagram shows it as p/n 113
You can obtain the trigger switch for the Chicago Electric 12" Sliding Saw model 98194, part number 113, by calling the technical support or replacement parts line at 1-800-444-3353.
This answer is automatically generated
Please help me find a replacement laser for my Chicago 98194
The Chicago Electric 98194 uses two ‘AAA’ batteries for its laser. There is no mention of replacing the laser unit itself, only the batteries.
This answer is automatically generated
how to obtain a kerf board for a chicago electric miter saw sku 98194
The manual does not specify how to obtain a replacement Kerf Board for the Chicago Electric miter saw model 98194. However, for technical questions or parts inquiries, you can contact Harbor Freight Tools at 1-800-444-3353.
This answer is automatically generated