Chicago Electric 98199 Owner's And Safety Manual
  1. Manuals
  2. Brands
  3. Chicago Electric Manuals
  4. Saw
  5. 98199
  6. Owner's and safety manual

Chicago Electric 98199 Owner's And Safety Manual

10" sliding compound miter saw
Hide thumbs Also See for 98199:

Advertisement

Table of Contents

Advertisement

Table of Contents
loading

Related Manuals for Chicago Electric 98199

Summary of Contents for Chicago Electric 98199

  • Page 2: Table Of Contents

    Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Addresses practices not related to personal injury. Page 2 For technical questions, please call 1-888-866-5797. ITEM 98199...

  • Page 3: Safety

    NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop. ITEM 98199 For technical questions, please call 1-888-866-5797. Page 3...
  • Page 4 Do not change the plug in any way. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. Outlets for 2-Prong Plug (See Outlets for 2-Prong Plug.) Page 4 For technical questions, please call 1-888-866-5797. ITEM 98199...
  • Page 5 The guards close proximity to heart pacemaker could cause of this saw are not designed to protect pacemaker interference or pacemaker failure. against the failure of such blades. ITEM 98199 For technical questions, please call 1-888-866-5797. Page 5...

  • Page 6: Vibration Safety

    If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. SAVE THESE INSTRUCTIONS. Page 6 For technical questions, please call 1-888-866-5797. ITEM 98199...

  • Page 7: Specifications

    Left Miter 0° - 45° left Scale 1° per scale mark 250100 List of Contents Description Compound Sliding Miter Saw Carbide Tipped Blade Table Extensions Dust Collection Bag Wrench ITEM 98199 For technical questions, please call 1-888-866-5797. Page 7...
  • Page 8 Blade Lock Dust Collection Bag Blade Hold Down Clamp Kerf Board Miter Handle Table Bevel Angle Indicator Fence Miter Angle Miter Lock Indicator Handle Work piece Extension Support Figure A: Components Page 8 For technical questions, please call 1-888-866-5797. ITEM 98199...

  • Page 9: Setup

    Also, the use of a saw table will make it easier to efficiently handle work materials and make more accurate cuts. ITEM 98199 For technical questions, please call 1-888-866-5797. Page 9...

  • Page 10: Operation

    If the work surface and any work materials supports are not level, and on the same level, unwanted bevel angles will appear in the cuts resulting in poor joinery. Page 10 For technical questions, please call 1-888-866-5797. ITEM 98199...
  • Page 11 Depth Stop Screw, the shallower the cut will be. to control the depth of the cut. After the desired cut has been made, return the Depth Stop Screw to its open position by turning it counterclockwise. REV 10f ITEM 98199 For technical questions, please call 1-888-866-5797. Page 11...

  • Page 12: General Operating Instructions

    This is the “kerf”. To prevent your work piece from being cut too short, align the edge of the blade with your measured mark, keeping the kerf on the waste side of the cut. Page 12 For technical questions, please call 1-888-866-5797. ITEM 98199...

  • Page 13: Maintenance

    Dull blades will cause increased tear-out and ragged edges on the cuts. WARNING! If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician. ITEM 98199 For technical questions, please call 1-888-866-5797. Page 13...
  • Page 14 Rotate the Center Cover back into place and tighten the Center Cover Fixing Bolt using the Wrench by turning it clockwise. Release the Locking Pin. Figure D: Raise Blade Guard Page 14 For technical questions, please call 1-888-866-5797. ITEM 98199...
  • Page 15 Install a new Kerf Board. Replace the left side of the Blade clears the Kerf Board. Tighten four screws and tighten them slightly. the four screws holding the Kerf Board in place. ITEM 98199 For technical questions, please call 1-888-866-5797. Page 15...

  • Page 16: Troubleshooting

    LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Page 16 For technical questions, please call 1-888-866-5797. ITEM 98199...

  • Page 17: Parts List And Diagram

    Lock Button 124 Power Wire Bend Arm Lock Button Spring 125 Rubber sheath Flat Washer Spring Washer 126 Handle Lock Nut Block Plate 127 Spanner Washer Spring 128 Bearing REV 11a ITEM 98199 For technical questions, please call 1-888-866-5797. Page 17...

  • Page 18: Assembly Diagram

    Assembly Diagram Page 18 For technical questions, please call 1-888-866-5797. ITEM 98199...
  • Page 19 Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. ITEM 98199 For technical questions, please call 1-888-866-5797. Page 19...

  • Page 20: Warranty

    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.

This manual is also suitable for:

61972

Table of Contents