Page 1
10” COMPOUND MITER SAW 91995 SET UP AND OPERATINg INSTRUCTIONS Distributed exclusively by Harbor Freight Tools ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury.
Page 3
ALWAYS USE SAFETY GLASSES. mounting, and any other conditions Also use face or dust mask if cutting that may affect its operation. A guard operation is dusty. Everyday eye- REV 09d SKU 91995 For technical questions, please call 1-800-444-3353. Page 3...
The outlet must be properly installed and grounded in accordance with all Improper connection of the equip- codes and ordinances. ment-grounding conductor can re- sult in a risk of electric shock. The REV 09d SKU 91995 For technical questions, please call 1-800-444-3353. Page 4...
Saw Blade to cut without be- gUARD DISABlED, DAMAgED, ing forced. When turning off the Saw, OR REMOVED. Moving guards allow the Saw Blade to spin down REV 09d SKU 91995 For technical questions, please call 1-800-444-3353. Page 5...
Page 6
Avoid unintentional starting. Prepare ditions and situations that may occur. to begin work before turning on the It must be understood by the operator tool. that common sense and caution are REV 09d SKU 91995 For technical questions, please call 1-800-444-3353. Page 6...
Page 7
Wear suitable gloves to reduce the vibration effects on the user. Use tools with the lowest vibration when there is a choice between dif- ferent processes. Include vibration-free periods each day of work. REV 09d SKU 91995 For technical questions, please call 1-800-444-3353. Page 7...
When replacing the Saw Blade (56), make sure the new Saw Blade has a diameter of 10”, an RPM rating of at least 5,300, and an arbor hole of 5/8” diameter. REV 07k, 09d SKU 91995 For technical questions, please call 1-800-444-3353. Page 8...
Page 9
Saw Blade from being raised or lowered. (See Figure E.) FIgURE H Depress the Spindle Lock (84) to keep the Saw Blade (56) from turn- ing. (See Figure H.) Rev 07k SKU 91995 For technical questions, please call 1-800-444-3353. Page 9...
Page 10
Make sure the Safety Cover (53) (10). The Holders should be used as returns to its original position prior to supports when cutting longer length operating the Miter Saw. workpieces. (See Figure k.) SKU 91995 For technical questions, please call 1-800-444-3353. Page 10...
Do not operate the Miter Saw if the Trigger (See Figure N.) is not operating properly. To turn on the Miter Saw, simply squeeze the Trigger. To turn off the tool, release pressure on the Trigger. SKU 91995 For technical questions, please call 1-800-444-3353. Page 11...
Page 12
(11a), lower the Saw Blade further by loosening the Screw (92). (See Figure O.) After adjusting the Screw (92), press down on the Miter Saw and make sure the Saw Blade (56) does not SKU 91995 For technical questions, please call 1-800-444-3353. Page 12...
Page 13
Tilt the Back Rack (25) until the de- sired bevel angle of cut is achieved as indicated on the Gauge (24). Then, re-tighten the Handle (30) to lock the Back Rack in place. (See Figure P.) SKU 91995 For technical questions, please call 1-800-444-3353. Page 13...
If necessary, use a roller stand (not included) with a larger workpiece. Never attempt to remove material stuck in the moving parts of the Miter Saw while it is plugged in and run- ning. SKU 91995 For technical questions, please call 1-800-444-3353. Page 14...
Saw Blade (56). Replace the Brush Holders. NOTE: New Carbon Brushes tend to arc or spark when first used until they wear and conform to the Mo- tor’s Armature. SKU 91995 For technical questions, please call 1-800-444-3353. Page 15...
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 91995 For technical questions, please call 1-800-444-3353. Page 16...
Small Cover Screw Large Cover Fixed Rod Note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. REV 08h, 09d SKU 91995 For technical questions, please call 1-800-444-3353. Page 17...
ASSEMBlY DIAgRAM 110: WRENCH NOT SHOWN. Note: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. REV 08h, 09d SKU 91995 For technical questions, please call 1-800-444-3353. Page 18...
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353 REV 09d SKU 91995 For technical questions, please call 1-800-444-3353. Page 19...
Need help?
Do you have a question about the 91995 and is the answer not in the manual?
Questions and answers