SET Up ..........10 gEnErAl OpErATing inSTrUCTiOnS ........11 MAinTEnAnCE AnD SErViCing ...12 ClEAning, MAinTEnAnCE, AnD lUbriCATiOn ........12 TrOUblESHOOTing ......13 pArTS liST ........14 ASSEMblY DiAgrAM .....15 liMiTED 90 DAY WArrAnTY ..16 Page 2 For technical questions, please call 1-800-444-3353. SKU 91938...
DON’T FORCE TOOL. It will do the job could result in minor or moderate better and safer at the rate for which it injury. was designed. SKU 91938 For technical questions, please call 1-800-444-3353. Page 3...
Page 4
SECURE WORK. Use vise to hold work Don’t leave tool until it comes to a when practical. It’s safer than using your complete stop. hand and it frees both hands to operate tool. Page 4 For technical questions, please call 1-800-444-3353. SKU 91938...
Cut-Off Use only 3-wire extension cords that Wheel or another part, in all depths of have 3-prong grounding plugs and cut. SKU 91938 For technical questions, please call 1-800-444-3353. Page 5...
Page 6
Off Wheel is balanced and is not broken or bent. People with pacemakers should consult their physician(s) before use. Wear eye protection. Electromagnetic fields in close proximity to heart pacemaker could cause Page 6 For technical questions, please call 1-800-444-3353. SKU 91938...
Page 7
SAVE THESE Vibration Safety inSTrUCTiOnS. This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical SKU 91938 For technical questions, please call 1-800-444-3353. Page 7...
When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Vise Handle (28) Freight Tools at 1-800-444-3353 as soon as possible. Trigger (103) Lock Page 8 For technical questions, please call 1-800-444-3353. SKU 91938...
While holding the Lock Pin (63), tighten the Socket Head Bolt (54) with the Hex Push the Lock Pin (63) towards the Key (111a). Fixed Guard (60) as shown in FigUrE SKU 91938 For technical questions, please call 1-800-444-3353. Page 9...
Handle (28) up against the workpiece. Then tighten the Vise Handle (28). When releasing, loosen the Vise Handle (28) a few turns, lift up the Quick Release (31), and pull the Vise Handle (28) open. Page 10 For technical questions, please call 1-800-444-3353. SKU 91938...
Raise the Saw by pushing down on it and pulling out the Lock Ball (25). Plug the Power Cord into the nearest 120 V~, grounded, electrical outlet. Slide the Trigger Lock and pull the Trigger to SKU 91938 For technical questions, please call 1-800-444-3353. Page 11...
AFTEr USE, wipe external surfaces of the tool with clean cloth. WArning! if the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician. Page 12 For technical questions, please call 1-800-444-3353. SKU 91938...
See Extension Cords in GROUNDING section. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. SKU 91938 For technical questions, please call 1-800-444-3353. Page 13...
If product has no serial number, record month and year of purchase instead. note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. rEV 10a Page 14 For technical questions, please call 1-800-444-3353. SKU 91938...
Camarillo, CA 93011 • (800) 444-3353 not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. Page 16 For technical questions, please call 1-800-444-3353. SKU 91938...