Panasonic SC-BT205 Operating Instructions Manual page 49

Displays
The display is dim.
The elapsed time displayed
is actually less than the
play time.
TV screen and video
The images from this unit
do not appear on the
television.
Picture is distorted.
Jittering occurs.
Picture stops.
The screen changes
automatically.
Video is not output.
Video is not output in high
definition.
The Setup menu cannot be
accessed.
Status messages do not appear.
The 4:3 aspect ratio picture
expands left and right.
Screen size is wrong.
When playing DVD-Video
using progressive output, one
part of the picture momentarily
appears to be doubled up.
There is no apparent change
in picture quality when
adjusted with the "Picture"
menu in the on-screen menu.
The masked-off area is
masked in grey.
Still pictures (JPEG) do not
playback normally.
After choosing "Home Cinema"
in "Speaker Selection" with the
TV's remote control, the TV's
input selection also changes.
≥Change "FL Display" in the Setup menu.
≥The displayed play time is converted from the number of frames at 29.97 frames
(equal to 0.999 seconds) to one second. There will be a slight difference between
the time displayed and the actual elapsed time (e.g., actual one-hour elapsed time
may display as approximately 59 minutes 56 seconds).
≥Make sure that the television is connected to the VIDEO OUT terminal,
COMPONENT VIDEO OUT terminals or HDMI AV OUT terminal on this unit.
≥Make sure that the television's input setting (e.g., AV 1) is correct.
≥An incorrect resolution is selected in "HDMI Video Format", when the television is
connected to HDMI AV OUT terminals. While stopped, press and hold [1PLAY] and
[∫STOP] on the main unit at the same time for more than 5 seconds to cancel this setting.
Set the item again. However, Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio
are not output in bitstream. To output the bitstream, select "Default Settings" to
restore the factory presets and make proper settings.
≥To output video from a device connected with an HDMI cable, set "HDMI Video
Mode" to "On" in the Setup menu.
≥If "24p Output" is set to "On" when the unit is connected to a TV through any terminal other
than HDMI, images may not display properly. In this case, set "24p Output" to "Off".
≥When "24p Output" is set to "On", HDMI authentication takes place where 24p
images switch to other images, and a black screen is displayed.
≥When "24p Output" is set to "On", jittering may occur while playing DVD-Video. In
this case, turn "24p Output" to "Off".
≥An incorrect resolution is selected in "Component Resolution", when the television is
connected to COMPONENT VIDEO OUT terminals. While stopped, press and hold
[1PLAY] and [∫STOP] on the main unit at the same time for more than 5 seconds to
cancel this setting. Set the item again.
≥Picture may not be seen when more than 2 devices are connected with HDMI cables.
Reduce the number of connected devices.
≥The unit and television are using different video systems. While stopped, keep
pressing [∫STOP] and [< OPEN/CLOSE] on the main unit for 5 or more seconds.
The system switches from PAL to NTSC or vice versa.
≥The system used on the disc doesn't match your television.
–PAL discs cannot be correctly viewed on an NTSC television.
–This unit can convert NTSC signals to PAL60 for viewing on a PAL television
("NTSC Contents Output" in the "Picture").
≥ Images may not be output due to how files were created.
[DivX]
≥If you are using an indoor TV antenna, change to an outdoor antenna.
≥The TV antenna wire is too close to the unit. Move it away from the unit.
≥ Picture may stop if the DivX files are greater than 2 GB.
[DivX]
≥When the "Screen Saver Function" in the Setup menu is set to "On", the display
may return to the screen saver mode automatically if there is no operation for
5 minutes or more.
≥An image is not output from the COMPONENT VIDEO OUT terminal or the VIDEO
OUT terminal when the "High Clarity Sound" is enabled. Set the "High Clarity
Sound" in the on-screen menu to "Off" to use the COMPONENT VIDEO OUT
terminal or the VIDEO OUT terminal.
≥High definition video cannot be output through the VIDEO OUT terminal.
≥Confirm that the "HDMI Video Mode", "HDMI Video Format", and "Component
Resolution" in the Setup menu are set properly.
≥The video output resolution is restricted to "576p/480p" when DVD-Video discs,
DivX and BD-Video discs recorded at a rate of 50 field per second are output from
the COMPONENT VIDEO OUT terminals.
≥Select "BD/DVD" as the source.
≥Select "Automatic" in "On-Screen Messages" in the Setup menu.
≥Use the television to change the aspect. Refer to your television's operating instructions.
≥When using a component video cable, set "Progressive" to "Video". If the situation
is not restored after that, set "TV Aspect" to "4:3".
≥When using an HDMI cable, set "TV Aspect" to "16:9".
≥When you use the HDMI AV OUT terminal for video output, follow the steps below for setting.
1 Connect this unit to the TV with any cable except the HDMI cable.
2 When you connect with the Component Video cable, set "HDMI Video Mode" to
"Off" and "Component Resolution" to "576i/480i" in the Setup menu.
≥The effect is less perceivable with some types of video.
≥If the "Screen Saver Function" in the Setup menu is set to "Off", the masked-off
area is displayed in black.
≥The images that were edited on the PC, such as Progressive JPEG, etc., may not
playback.
≥Disconnect the HDMI cable from the TV and reconnect it to a different HDMI
terminal.
Page
38
—
10, 11
—
39
39
39
39
39
39
—
—
—
37
—
—
—
—
38
36
—
39
—
—
38
—
36, 39
39
39
—
38
46
—
RQT9445
49