Download  Print this page

Enjoying Tv, Etc. With This Unit's Speakers; Enjoying Tv And Other Devices Sound From This Unit's Speakers; Adjusting The Sound; Making Settings For Digital Audio Input - PANASONIC SC-BT205 Operating Instructions Manual

Blu-ray disc home theater sound system.
Hide thumbs

Advertisement

Enjoying TV, etc. with this unit's speakers

You can enjoy TV broadcasts with this unit's speakers.
SURROUND
SURROUND
STATUS
STATUS
Preparation
Confirm the audio connection to the OPTICAL IN or AUX
terminal on this unit (
10 to 12).
Turn on the TV.
1 Press [EXT-IN] several times to select "D-IN 1"
(DIGITAL IN 1) *
, "D-IN 2" (DIGITAL IN 2) *
1
"AUX" *
.
1
This unit: Press [SELECTOR].
≥D-IN 1 (DIGITAL IN 1)*
When connecting using OPTICAL 1(TV) terminal.
≥D-IN 2 (DIGITAL IN 2)*
When connecting using OPTICAL 2(STB) terminal.
:
≥AUX*
1
When connecting using AUX terminal.
*
For connections with the TV. (
1
*
For connections with other devices. (
2
≥When the system is connected to an HDAVI Control 2 or
later-compatible TV via an HDMI cable, TV broadcast audio
is output through the system speakers if the TV input is
switched to TV tuner mode. See "Setting the TV audio for
VIERA Link "HDAVI Control"" on page 28 for setting method.
≥Reduce the volume on the TV to its minimum, and then
adjust the volume of this unit.
Enjoying TV and other devices sound
from this unit's speakers
You can enhance stereo sources with surround sound effect.
Press [SURROUND] several times to select the mode.
≥You can also press [SURROUND] and then [3, 4] to
select the mode.
≥The selected effect will only be displayed on the main
unit.
While "MANUAL" is displayed
Press [2, 1] and select the desired effect.
Recommended modes to enjoy TV audio:
≥DOLBY PL II MOVIE
≥DOLBY PL II MUSIC
≥S.SURROUND
For more detailed information on this operation, please refer to
the "Enjoying surround sound effects" section on page 17.
EXT-IN
EXT-IN
SOUND
SOUND
OK
SD CARD
SETUP MIC
SELECTOR
SELECTOR
TUNE
SELECTOR
or
2
1
:
:
2
10, 11)
12)

Adjusting the sound

You can adjust the mode depending on the source or situation.
1 Press [SOUND] several times to select the mode.
≥You can also press [SOUND] and then [3, 4] to select
the mode.
≥The selected effect will only be displayed on the main
unit.
While the selected mode is displayed
2
Press [2, 1] and select the desired setting.
For more detailed information on this operation, please refer to
the "Changing the sound modes" section on page 17.

Making settings for digital audio input

Select to suit the type of audio from the OPTICAL IN terminals
on the main unit.
≥Underlined items are the factory presets.
Available settings
Mode
DUAL:
(Only works with Dolby Dual Mono)
–M1
–M2
–M1+M2(stereo audio)
≥If this is set to "M1" or to "M2", the "PCM FIX"
will automatically be set to "OFF"(
DRC:
–ON
Adjust for clarity even when the volume is low by
(Dynamic
compressing the range of the lowest sound level
Range
and the highest sound level. Convenient for late
Compression)
night viewing. (Only works with Dolby Digital)
–OFF
The full dynamic range of the signal is
reproduced.
PCM FIX:
–ON
Select when receiving only PCM signals.
–OFF
Select when receiving Dolby Digital and
PCM signals.
≥When receiving true 5.1-channel surround
sound, select "OFF".
: –AUX
TV AUDIO*
3
Select when receiving analogue sound from
the TV to the AUX terminal.
–D-IN 1
Select when receiving digital sound from the
TV to the OPTICAL 1(TV) terminal.
CABLE/SAT
–SET
Select when setting the main unit to switch to "D-IN
AUDIO*
:
4,5
2" when the input channel of a HDMI connected
STB is selected on the TV ( 28, Setting the TV
audio for VIERA Link "HDAVI Control").
–OFF
Select to cancel this setting.
1 Press [EXT-IN] several times to select "D-IN 1"
(DIGITAL IN 1) or "D-IN 2" (DIGITAL IN 2).
Main unit: Press [SELECTOR].
2 Press [STATUS] several times to select the
mode.
≥You can also press [STATUS] and then [3, 4] to select
the mode.
≥The digital audio input settings are to be set separately
to each source, "D-IN 1" and "D-IN 2".
≥The selected effect will only be displayed on the main unit.
While the selected mode is displayed
3
Press [2, 1] and select the desired setting.
*
When "D-IN 1" is selected.
3
*
When "D-IN 2" is selected.
4
*
The device connected to the OPTICAL 2(STB) terminal must be
5
connected to the TV via an HDMI cable. If it is not connected via an
HDMI cable, "NOT CONDITIONAL" is displayed on the main unit.
≥Audio that is input through the OPTICAL DIGITAL
IN or AUX terminals are not output from the HDMI
terminal.
NOTE
Setting
below).
RQT9445
27

Advertisement

Table of Contents

   Related Manuals for PANASONIC SC-BT205

Comments to this Manuals

Symbols: 0
Latest comments: