Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Craftex CX502
Summary of Contents for Craftex CX502
- Page 1 CX502 OSCILLATING VERTICAL SPINDLE SANDER User Manual...
-
Page 2: Table Of Contents
TABLE OF CONTENTS General Safety Instructions for Machines ............... 3 Specific Safety Instructions..................4 Features........................5 Physical Features ....................6 Proper Grounding ....................7 Un-Packing ......................7 Magnetic Switch...................... 8 Dust Collection......................8 Spindle Drum ......................8 Selecting Proper Size Drum & Table Insert ............9 Tilting the Table ...................... -
Page 3: General Safety Instructions For Machines
GENERAL SAFETY INSTRUCTIONS FOR MACHINES Extreme caution should be used when operating all power tools. Know your power tool, be familiar with its operation, read through the owner’s manual and practice safe usage procedures at all times. ALWAYS read and understand the NEVER leave a tool unattended while it user manual before operating the is in operation. -
Page 4: Specific Safety Instructions
CX502 OSCILLATING VERTICAL SPINDLE SANDER SPECIFIC SAFETY INSTRUCTIONS MAKE SURE the sander is connected DO NOT force the sander. It will do the to the matched and specific power job better and will be safer at the source instructed in the manual. -
Page 5: Features
Excellence. By following the instructions and procedures laid out in this user manual, you will receive years of excellent service and satisfaction. The CX502 is a professional tool and like all power tools, proper care and safety procedures should be adhered to. -
Page 6: Physical Features
CX502 OSCILLATING VERTICAL SPINDLE SANDER PHYSICAL FEATURES Spindle Sanding Spindle Sleeve Washer Table Insert Work Table Accessory Storage Area Powder Coated Paint ON/OFF Switch Sander Base Rubber Feet... -
Page 7: Proper Grounding
WARNING risk of electric shock. Improper connection of the equipment- CX502 is for use on a normal 110 volt grounding conductor can result in a risk circuit. Make sure that the machine is of electric shock. Check with a qualified... -
Page 8: Magnetic Switch
Use an open-end DUST COLLECTION wrench holding the spindle with its flat The CX502 is equipped with a 2” diameter surface from the bottom of the table and at dust port for optimum dust removal. -
Page 9: Selecting Proper Size Drum & Table Insert
Once the table is at the desired angle, SELECTING PROPER SIZE tighten the two table lock knobs securely to DRUM & TABLE INSERT secure the table in position. The machine comes with five spindle drums; 1/4", 1/2", 5/8”, 1-1/2” and 2”. Figure-6 Tilting the table SANDING TIPS Always select the spindle that is smaller... -
Page 10: Maintenance
MAINTENANCE During the life of your tool, you will need to To check if the spindle is square to the practice some regular maintenance to keep table: your sander in peak performance condition. Make sure the switch is in the OFF position and the cord is disconnected from the power source. -
Page 15: Parts List
CX502 PARTS LIST PART# DESCRIPTION BASE 101A TOP PLATE STRAIN RELIEF POWER CORD SCREW RND HD M6-1.0 X 25 RUBBER FEET WASHER 1/4 NUT - HEX M6-1.0 WASHER - LOCK M4 SCREW RD HD M4-0.7 X 10 CX502MOT MOTOR 1/2 HP KEY 6 X 6 X 50 SCREW FLAT HD M4- 0.7 X 15... - Page 16 MAIN CASTING 304-A BRACKET RIGHT 304-B BRACKET LEFT BOLT HEX HD M8-1.25 X 16 HEX BOLT M8-1.25 X 110 NUT - HEX M8-1.25 310-a GRADUATION DIAL -RIGHT 310-A GRADUATION DIAL - LEFT LEVER M5-0.8 X 16 SCREW - FLAT HEAD M5-0.8 X 15 SCREW SET SOC HD M6-1.0 X 6 WIDTH POINTER WASHER STAR 3/16...
-
Page 17: Warranty
Proof of purchase is necessary. All warranty claims are subject to inspection of such products or part thereof and Craftex reserves the right to inspect any returned item before a refund or replacement may be issued.
Need help?
Do you have a question about the CX502 and is the answer not in the manual?
Questions and answers