Hatteland HD 12T21 STD-xxx-Fxxx User Manual page 77

Pinout Assignments
8-pin Digital Output / Input Module
"Solid State Relay"
3 A
X1
DIG
OUT
1
1
X1
DIG
IN
Pin 01 X1 - Out: 41 Out +
Pin 02 X1 - Out: 42 Out -
COM (Common Center
Pin 03 X1 - Out: 31
Terminal) *
Pin 04 X1 - Out: 32 NC (Normally Closed)*
* IEC 60950 Compliant, 48VDC
Pin 01 X1 - In: 52
+24VDC
Pin 02 X1 - In: 53 GND (Ground)
Pin 03 X1 - In: 61 +24VDC
Pin 04 X1 - In: 62 +Input
5-pin Digital Output Module
"Safety Signal Relay"
3 A
X1
DIG
OUT
1 2 3 4
COM (Common
PIN 01 X1 - Out: 11
Center Terminal)
Not Connected
PIN 02 X1 - N/C
Not in use
PIN 03 X1 - Out: 14 NO (Normally Open)
Not Connected
PIN 04 X1 - N/C
Not in use
PIN 05 X1 - Out: 12 NC (Normally Closed)
Appendix
IND100241-13
10-pin Digital Output / Input & Serial Module
"Mechanical Relay & COM (isolated RS-422/485)"
2 3 4
2 3 4
PIN 01 X1 - Out: 21
PIN 02 X1 - N/C
PIN 03 X1 - Out: 24 NO (Normally Open)
PIN 04 X1 - N/C
PIN 05 X1 - Out: 22 NC (Normally Closed)
PIN 01 X7 - In: 71
PIN 02 X7 - In: 72
PIN 03 X7 - Out: 73
PIN 04 X7 - Out: 74
PIN 05 X7 - GND: 75 SGnd (Signal Ground)
10+10 pin RS-422 / RS-485 NMEA Module
5
PIN 01 TxD-
PIN 02 TxD+ Transmit Data Positive
PIN 03 GND
PIN 04 RxD-
PIN 05 RxD+ Receive Data Positive
PIN 06 TxD-
PIN 07 TxD+ Transmit Data Positive
PIN 08 GND
PIN 09 RxD-
PIN 10 RxD+ Receive Data Positive
RS-485 Half Duplex (2-wire) Configuration:
*Note: The jumper for "force of transmitter" is
open by factory default. For some custom
models this jumper is preset to closed (active),
in that case unit has to be opened and jumper
set to open to allow Half Duplex mode.
3 A
X1
DIG
OUT
1 2 3 4 5
1 2 3 4 5
X7
SER
I/O
COM (Common Center
Terminal)
Not Connected / Not used
Not Connected / Not used
Rx+ (Receive Data +)
Rx- (Receive Data -)
Tx+ (Transmit Data +)
Tx- (Transmit Data -)
Type Number "PCA100293-1"
3 A B
6 7 8 9 1 0 6 7 8 9 1 0
1 2 3 4 5 1 2 3 4 5
Transmit Data Negative
Isolated Ground
Receive Data Negative
Transmit Data Negative
Isolated Ground
Receive Data Negative
Connect TX and RX pair-wise:
TX- to RX-, TX+ to RX+.
77
4+4 pin CAN I/O Module, 2 channels
Type Number "HT 00254 OPT-A1"
3 A B
X8
CAN1
1 2 3
1 2 3
X9
CAN2
Pin 01 X8 - Can1: 81 In Low
Pin 02 X8 - Can1: 82 Out Low
Pin 03 X8 - Can1: 83 In High
Pin 04 X8 - Can1: 84 Out High
Pin 01 X9 - Can2: 91 In Low
Pin 02 X9 - Can2: 92 Out Low
Pin 03 X9 - Can2: 93 In High
Pin 04 X9 - Can2: 94 Out High
10-pin RS-422 / RS-485 Module
"RS-422/RS-485 SCOM Buzzer"
1 2 B
2 4 6 8 10
1 3 5 7 9
PIN 01* RxD+ Receive Data Positive
PIN 02 GND Ground
PIN 03* RxD- Receive Data Negative
PIN 04 +5V +5V Out
PIN 05* TxD+ Transmit Data Positive
PIN 06 BUZ- Buzzer Control Negative
PIN 07* TxD- Transmit Data Negative
PIN 08 BUZ+ Buzzer Control Positive
PIN 09 GNDR Ground 100Ω
PIN 10 GND Ground
*Pin 1,3,5,7 = RS-485 Full Duplex (4-wire)
*Pin 5,7 = RS-485 Half Duplex (2-wire)
4
4