E-Rb Recumbent Bike Assembly And Setup - Star Trac E-UB Owner's Manual

E-RB RECUMBENT BIKE ASSEMBLY AND SETUP

Use the following procedures to unpack and assemble your STAR TRAC E-UB RECUMBENT BIKE.
U
NPACKING
Open the shipping carton, remove all parts from the carton and foam inserts, and verify that the following parts are included in your ship-
ment:
Bike Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Display Console Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 1
Seat Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Front Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Rear Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pedals (set of two) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Screw, Button Head, M10 X 30 . . . . . . . . . . . . . . . . . . . . . 8
Take time now to enter your E SERIES BIKE serial number in the space below. If parts are missing, or if you have any operational ques-
tions, please call Star Trac's Service Department at (800) 503-1221; have your serial number ready.
Serial No. ___________________________
A
SSEMBLY
The front foot assembly has wheels attached to the front
edge. Be sure the wheels face forward when installing the front foot
assembly.
Stand the bike frame upright on the floor. Raise the front end of the
bike frame by placing a 2-inch Styrofoam spacer under the front main
beam. Insert four M10 X 30 button head screws through the holes in
the front foot attachment plate.
Position the front foot assembly under the attachment plate, aligning
the holes in the foot with the four screws.
Using the 6mm hex wrench, secure the front foot assembly to the
frame with the four M10 X 30 button head screws. Tighten all four
screws securely.
Be sure the rear foot assembly is positioned with the curved
edge facing forward (similar to the front foot).
Lift up the rear of the bike frame and place the rear foot assembly in
position under the frame, aligning the holes in the foot with the holes
in the frame.
Using the 6mm hex wrench and four M10 X 30 button head screws,
secure the rear foot assembly to the frame. Tighten all four screws
securely.
STAR TRAC E SERIES BIKES O ' G
WNER S UIDE
Screw, Socket Head, M10 X 10 . . . . . . . . . . . . . . . . . . . . . 4
Screw, Flat Head, M6 X 20 . . . . . . . . . . . . . . . . . . . . . . . . 4
Wrench, Hex, 6mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Wrench, Hex, 4mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Wrench, Hex, 3mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Multi-end Wrench, 10mm, 12mm,15mm . . . . . . . . . . . . . . 1
15