Table of Contents
Advertisement
Cybex 600T Treadmill Owner's Manual
belt is slipping. If the belt does slip, use a wrench to equally tighten both rear roller
adjustment bolts 1/2 of a turn (clockwise). Adjust the belt until no further slipping
is felt.
Running Belt Maintenance
The running belt and deck should be checked periodically for any excessive
wear. The belt may need minor adjustments. Use the following section to help
keep your 600T operating properly.
Checking the Belt and Deck Surfaces — In an effort to make sure that the
running belt operates properly, visually inspect the belt on a weekly basis to
make sure that there are no tears or fraying in the belt material.
To inspect the edges of the belt, it is necessary to remove the plastic side rails.
Follow these steps:
1. Turn the power off.
A. Turn the main power switch on the front panel to the off (O) position.
B. Unplug the treadmill from the power outlet.
! WARNING: When removing or installing the side rails be sure to wear
work gloves to protect against any sharp edges.
2. Remove the plastic end caps and side rails.
A. Remove the Phillips head screws that fasten each of the plastic end
caps in place and set aside. See Figure 2.
B. Grab the side rail and firmly slide it out towards the back of
the treadmill.
Figure 2
End Caps
Phillips Head
Screws
Table of Contents
i
Read All Instructions & Warnings
ii
Important Safety Instructions
iv
About This Manual
Important Voltage Information iv
FCC Compliance Information . iv
v
Declaration of Conformity
vii
Table of Contents
1
Safety
Warning Decals. . . . . . . . . . . 1-1
Caution Decals . . . . . . . . . . . 1-2
2
Technical Specifications
Specifications . . . . . . . . . . . . 2-1
Stableflex System . . . . . . . . . 2-2
3
Operation
Quick Start . . . . . . . . . . . . . . 3-1
Stopping the Treadmill . . . . . 3-1
Automatic Stop Feature . . . . 3-1
Selecting Programs
& Options. . . . . . . . . . . . . . 3-2
Displaying Heart Rate . . . . . . 3-2
The Workout Graph. . . . . . . . 3-2
Detailed Operation Guide . . . 3-3
Control During Operation . . . 3-4
Changing Data Readouts . . . 3-5
Use of Programs. . . . . . . . . . 3-6
4
Preventive Maintenance
Regular Maintenance
Activities. . . . . . . . . . . . . . . 4-1
Running Belt Maintenance . . 4-3
5
Setup & Assembly
Quick Setup . . . . . . . . . . . . . 5-1
Choosing & Preparing
a Site . . . . . . . . . . . . . . . . . 5-1
Electrical Power
Requirements. . . . . . . . . . . 5-3
Unpacking. . . . . . . . . . . . . . . 5-3
Assembling the Treadmill . . . 5-4
Auto Tuning. . . . . . . . . . . . . 5-10
Testing the 600T
Operation. . . . . . . . . . . . . 5-11
Setting Operation Options . 5-12
6
Customer Service
Contacting Service . . . . . . . . 6-1
Serial Number & Voltage . . . . 6-1
Warranty . . . . . . . . . . . . . . . . 6-1
Return Material
Authorization (RMA). . . . . . 6-3
Damaged Treadmill or Parts . 6-3
7
Index . . . . . . . . . . . . . . . . . 7-1
Page 4-3
Advertisement
Table of Contents
