Page 1
SUPER USER’S MANUAL This is HIGH-POWER item; please DO NOT USE THE SAME OUTLET WITH OTHER HIGH-POWER HOUSEHOLD APPLIANCE like air-conditioning etc. Please choose an outlet exclusively for the machine and make sure the fuse is 10A. Product may vary slightly from the item pictured due to model upgrades...
IMPORTANT SAFETY PRECAUTIONS CAUTION: Before starting any exercise program, consult with your physician or health professional. IMPORTANT: Read all instructions carefully before using this product. Retain this owner’s manual for the future reference. 1. Plug the power cord of the treadmill directly into a dedicated grounded circuit. This product must be grounded well.
movement, may affect the accuracy of heart rate readings. The pulse sensors are intended only as exercise aids in determining heart rate trends in general. For your information, please note following electrical specification of Treadmill: a. The input voltage: 240V±10% (50HZ) b.
Page 6
Name Specification Name Specification Fixed pin Circuit wire and plug According to order φ5X1X12 Pin spring φ8.2Xφ0.8X15 Outerφ16*Outerφ Steel bushing Lifting motor 1/15Hp 14outer*φ10.1*12 Inner hexagonal wrench Display wrench S13、S14、S15 Square magnet Line length 1000mm φ32 spring sleeve Hand pulse set Line length 380mm φ38 spring sleeve Trunk line 2...
25. inner hexagonal bolt M8x65 teeth length 20 28.Washer 7. Spring washer Tools and nuts list: Part NO. Name Specification Cross-head wrench S13,S14,S15 Inner hexagonal wrench ASSEMBLY INSTRUCTIONS Take out all the assembly parts from the treadmill package. 2. (1)Insert arc washer(7) into inner hexagonal pan-headed bolt(14), and fix them into the separate holes with inner hexagonal wrench ;...
Page 8
4.Put the washer(28) into the inner hexagonal pan-headed bolt(25),and tighten the peddle fixed set to the left and right frames. CAUTION: 1. DO NOT PLUG IN POWER CORD UNTIL FINAL ASSEMBLY IS COMPLETED AND MOTOR COVER IS INSTALLED. 2. Do not attempt to assemble the treadmill until the assembly instructions are followed and the uprights are attached to the treadmill.
WE RECOMMEND YOU HAVE SOMEONE TO ASSIST YOU IN LIFTING AND ASSEMBLING YOUR LIFESPAN TREADMILL. FOLLOW THESE INSTRUCTIONS CAREFULLY AND IT WILL MAKE IT EASIER TO ASSEMBLE YOUR LIFESPAN TREADMILL Operation Guide ·1 Basic Characters: 1. Speed Range:1.0~20.00KM/H 2. Time Range: 0:00~99:59 3.
Press SPEED UP/SPEED DOWN once, the speed will increase/decrease 0.1km/h. But if the speed reaches 20.0km/h, pressing SPEED UP will no longer increase the speed. 4.START Power the treadmill on and the safety key is in place, press START, the treadmill will work except using the fat test program.
Page 11
screens display “OFF”, the buzzer gave forth “BB” noise. At the moment, you can do nothing except turning it off. Re-put the safety key on, the treadmill will re-enter into standby mode. ·9 Precautions 1. Before doing exercise, please check if the power is connected, if the power switch turn on, and if the safety key is validity.
Never use solvents, as they can cause damage to the treadmill. • Inspect the power cord. If the power cord is damaged, contact Lifespan Fitness. • Make sure the power cord is not underneath the treadmill or in any other area where it can become pinched or cut.
(refer to section 4.4 for information). Please contact Lifespan Fitness with questions about applying lubricant to your treadmill. • Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.
If the surface is dry to the touch, apply a suitable silicone lubricant. We recommend you use a silicone based spray to lubricate your Lifespan Treadmill. This can be purchased from your local sports Retailer or a local hardware store.
Note: Adjustment is thru the small hold on the end caps. Tighten the rear roller only enough to prevent slippage at the front roller. Turn both the right and left bolt clockwise reasonably and inspect for proper tension. When an adjustment is made to the belt tension, you must also make a tracking adjustment to compensate for the change in belt tension.
Display shows normal The input voltage is The input power should operation, strap, too low. meet the requirement. however, operates improperly and suffers from a cacophony. electric running The strap becomes Adjust the strap following machine operates normally loose. the specification. with load halts...