Yamaha Drag Star XVS250 Owner's Manual
  1. Manuals
  2. Brands
  3. Yamaha Manuals
  4. Motorcycle
  5. Drag Star XVS250
  6. Owner's manual

Yamaha Drag Star XVS250 Owner's Manual

Drag star 2000
Hide thumbs Also See for Drag Star XVS250:
Table of Contents

Advertisement

Quick Links

OWNER'S MANUAL
XVS250
5KR-28199-E0

Advertisement

Table of Contents
loading

Related Manuals for Yamaha Drag Star XVS250

Summary of Contents for Yamaha Drag Star XVS250

  • Page 1 OWNER’S MANUAL XVS250 5KR-28199-E0...
  • Page 3 EAU03338 Welcome to the Yamaha world of motorcycling! As the owner of an XVS250, you are benefiting from Yamaha’s vast experience and newest technology regarding the design and manufacture of high-quality products, which have earned Yamaha a reputation for dependability.
  • Page 4 This manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle is subsequently sold. Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your motorcycle and this manual.

  • Page 5: Important Manual Information

    IMPORTANT MANUAL INFORMATION EW000002 WARNING PLEASE READ THIS MANUAL CAREFULLY AND COMPLETELY BEFORE OPERATING THIS MOTORCYCLE.
  • Page 6 IMPORTANT MANUAL INFORMATION EAU03337 XVS250 OWNER’S MANUAL © 2000 by Yamaha Motor Co., Ltd. 1st Edition, July 2000 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Co., Ltd. is expressly prohibited. Printed in Japan.

  • Page 7: Table Of Contents

    TABLE OF CONTENTS EAU00009 GIVE SAFETY THE RIGHT OF WAY ....1-1 PRE-OPERATION CHECKS .......4-1 Pre-operation check list ........4-1 DESCRIPTION ...........2-1 Left view .............2-1 OPERATION AND IMPORTANT RIDING Right view............2-2 POINTS..............5-1 Controls and instruments ........2-3 Starting the engine ..........5-1 Starting a warm engine ........5-2 Shifting ..............5-3 INSTRUMENT AND CONTROL FUNCTIONS ..3-1 Recommended shift points...
  • Page 8 TABLE OF CONTENTS Adjusting the clutch lever free play ....6-19 Troubleshooting ..........6-40 Adjusting the brake lever free play ....6-20 Troubleshooting chart ........6-41 Adjusting the brake pedal position and free play ............6-20 MOTORCYCLE CARE AND STORAGE ..... 7-1 Adjusting the rear brake light switch ....

  • Page 9: Give Safety The Right Of Way

    EAU00021 GIVE SAFETY THE RIGHT OF WAY Motorcycles are fascinating vehicles, which can give you an unsurpassed feeling of power and freedom. However, they also impose certain limits, which you must accept; even the best motorcycle does not ignore the laws of physics. Regular care and maintenance are essential for preserving value and operating condition of your motorcycle.

  • Page 10: Description

    D ESCRIPTION EAU00026 Left view 1. Headlight (page 6-33) 5. Shock absorber assembly spring 2. Fuel cock (page 3-8) preload adjusting ring (page 3-10) 3. Fuses (page 6-32) 6. Shift pedal (page 3-5) 4. Helmet holder (page 3-9)

  • Page 11: Right View

    DESCRIPTION Right view 7. Owner’s tool kit (page 6-1) 11. Brake pedal (page 3-6) 8. Battery (page 6-30) 12. Oil filter element (page 6-10) 9. Air filter element (page 6-12) 13. Shock absorber assembly spring 10. Main switch/steering lock (page 3-1) preload adjusting ring (page 3-10)

  • Page 12: Controls And Instruments

    DESCRIPTION Controls and instruments 1. Clutch lever (page 3-5) 5. Brake lever (page 3-6) 2. Left handlebar switches (page 3-4) 6. Throttle grip (page 6-15) 3. Speedometer unit (page 3-3) 7. Fuel tank cap (page 3-6) 4. Right handlebar switches (page 3-4)

  • Page 13: Instrument And Control Functions

    EAU00027 I NSTRUMENT AND CONTROL FUNCTIONS 1. Push. 2. Turn. EAU00029 EAU00040 Main switch/steering lock LOCK EW000016 The steering is locked, and all electrical WARNING The main switch/steering lock controls systems are off. The key can be the ignition and lighting systems, and is Never turn the key to “OFF”...

  • Page 14: Indicator And Warning Lights

    ECA00043 the engine is defective. When this oc- CAUTION: 1. High beam indicator light “ ” curs, have the Yamaha dealer check 2. Turn signal indicator light “ ” Do not use the parking position for the self-diagnosis system. 3. Neutral indicator light “...

  • Page 15: Speedometer Unit

    2. Odometer CAUTION: 3. Tripmeter To prevent engine damage, be sure 4. Tripmeter reset knob to consult a Yamaha dealer as soon EAU00095 as possible if this occurs. Speedometer unit The speedometer unit is equipped with a speedometer, an odometer and a tripmeter.

  • Page 16: Handlebar Switches

    INSTRUMENT AND CONTROL FUNCTIONS EAU00127 Turn signal switch To signal a right-hand turn, push this switch to “ ”. To signal a left-hand turn, push this switch to “ ”. When released, the switch returns to the cen- ter position. To cancel the turn signal lights, push the switch in after it has re- turned to the center position.

  • Page 17: Clutch Lever

    INSTRUMENT AND CONTROL FUNCTIONS EAU00143 Start switch “ ” Push this switch to crank the engine with the starter. EC000005 CAUTION: See page 5-1 for starting instruc- tions prior to starting the engine. 1. Clutch lever 1. Shift pedal EAU00152 EAU00157 Clutch lever Shift pedal...

  • Page 18: Brake Lever

    INSTRUMENT AND CONTROL FUNCTIONS 1. Brake lever 1. Brake pedal 1. Unlock. EAU00158 EAU00162 EAU03756 Brake lever Brake pedal Fuel tank cap The brake lever is located at the right The brake pedal is on the right side of handlebar grip. To apply the front the motorcycle.

  • Page 19: Fuel

    INSTRUMENT AND CONTROL FUNCTIONS EAU00185 NOTE: CAUTION: The fuel tank cap cannot be installed unless the key is in the lock. In addition, Immediately wipe off spilled fuel the key cannot be removed if the cap is with a clean, dry, soft cloth, since not properly installed and locked.

  • Page 20: Fuel Cock

    INSTRUMENT AND CONTROL FUNCTIONS ON: normal position RES: reserve position PRI: priming position 1. Arrow mark positioned over “ON” 1. Arrow mark positioned over “RES” 1. Arrow mark positioned over “PRI” EAU03236 Fuel cock This indicates reserve. With the fuel This indicates prime.

  • Page 21: Starter (Choke) Lever

    INSTRUMENT AND CONTROL FUNCTIONS 1. Starter (choke) lever 1. Helmet holder 2. Unlock. EAU02976 Starter (choke) lever EAU00260 Helmet holder Starting a cold engine requires a richer To open the helmet holder, insert the air-fuel mixture, which is supplied by key into the lock, and then turn the key the starter (choke).

  • Page 22: Adjusting The Shock Absorber Assemblies

    INSTRUMENT AND CONTROL FUNCTIONS EAU00300 CI-10E Setting Adjusting the shock absorber Minimum (soft) assemblies Standard Each shock absorber assembly is Maximum (hard) equipped with a spring preload adjust- ing ring. EC000015 CAUTION: Never attempt to turn an adjusting 1. Spring preload adjusting ring mechanism beyond the maximum 2.

  • Page 23: Sidestand

    It cuts the running engine when check this system regularly as de- the transmission is in gear and the scribed below and have a Yamaha sidestand is moved down. dealer repair it if it does not function Periodically check the operation of the properly.
  • Page 24 5. Push the start switch. Does the engine start? The neutral switch may be defective. The motorcycle should not be ridden until checked by a Yamaha dealer. With the engine still running: 6. Move the sidestand up. 7. Keep the clutch lever pulled.

  • Page 25: Pre-Operation Checks

    • If necessary, add recommended oil to specified level. 6-10 • Check vehicle for oil leakage. • Check operation. • If soft or spongy, have Yamaha dealer bleed hydraulic system. • Check lever free play. Front brake • Adjust if necessary.
  • Page 26 Chassis fasteners — • Tighten if necessary. Instruments, lights, signals • Check operation. — and switches • Correct if necessary. • Check operation of ignition circuit cut-off system. Sidestand switch 3-11 • If system is defective, have Yamaha dealer check vehicle.
  • Page 27 PRE-OPERATION CHECKS NOTE: Pre-operation checks should be made each time the motorcycle is used. Such an inspection can be accomplished in a very short time; and the added safety it assures is more than worth the time involved. EWA00033 WARNING If any item in the Pre-operation check list is not working properly, have it inspected and repaired before operating the motorcycle.

  • Page 28: Operation And Important Riding Points

    The transmission is in the neutral Consult a Yamaha dealer re- position. garding any control or function The transmission is in gear with that you do not thoroughly the clutch lever pulled and the understand.

  • Page 29: Starting A Warm Engine

    OPERATION AND IMPORTANT RIDING POINTS 4. Turn the starter (choke) on and ECA00055 EAU01258 Starting a warm engine CAUTION: completely close the throttle. (See Follow the same procedure as for start- For maximum engine life, always page 3-9 for starter (choke) ing a cold engine with the exception warm the engine up before starting operation.)

  • Page 30: Shifting

    OPERATION AND IMPORTANT RIDING POINTS EC000048 EAU02941 Recommended shift points CAUTION: (for Switzerland only) Even with the transmission in The recommended shift points during the neutral position, do not acceleration are shown in the table be- coast for long periods of time low.

  • Page 31: Tips For Reducing Fuel Consumption

    The vehicle can now be operated of time (e.g., in traffic jams, at traf- normally. fic lights or at railroad crossings). EC000049 CAUTION: If any engine trouble should occur during the engine break-in period, immediately have a Yamaha dealer check the vehicle.

  • Page 32: Parking

    OPERATION AND IMPORTANT RIDING POINTS EAU00457 Parking When parking, stop the engine, re- move the key from the main switch, and then turn the fuel cock lever to “OFF”. EW000058 WARNING Since the engine and exhaust system can become very hot, park in a place where pedestri- ans or children are not likely to touch them.

  • Page 33: Periodic Maintenance And Minor Repair

    Periodic inspection, adjustment and lu- ence required for a particular job, have brication will keep your vehicle in the a Yamaha dealer perform it for you. safest and most efficient condition pos- EW000063 sible. The most important points of in-...

  • Page 34: Periodic Maintenance And Lubrication Chart

    The annual checks must be performed every year, except if a kilometer-based maintenance is performed instead. From 50,000 km, repeat the maintenance intervals starting from 10,000 km. Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and techni- cal skills.
  • Page 35 PERIODIC MAINTENANCE AND MINOR REPAIR ODOMETER READING ( 1,000 km) ANNUAL ITEM CHECK OR MAINTENANCE JOB CHECK • Check runout, spoke tightness and for damage. Wheels • Tighten spokes if necessary. • Check tread depth and for damage. • Replace if necessary. Tires •...
  • Page 36 PERIODIC MAINTENANCE AND MINOR REPAIR ODOMETER READING ( 1,000 km) ANNUAL ITEM CHECK OR MAINTENANCE JOB CHECK • Check the air cut valve and reed valve for damage. Air induction system • Replace the entire air induction system if necessary. Lights, signals and •...

  • Page 37: Removing And Installing Panels

    PERIODIC MAINTENANCE AND MINOR REPAIR 1. Panel A 1. Panel B 1. Panel lock cover 2. Unlock. EAU01122 Removing and installing EAU03184 Panel A panels To remove the panel The panels shown above need to be 1. Slide the lock cover open, insert removed to perform some of the main- the key into the lock, and then turn tenance jobs described in this chapter.
  • Page 38 PERIODIC MAINTENANCE AND MINOR REPAIR 1. Bolt 2. Pull the rear of the panel out with To install the panel EAU03185 Panel B the key inserted in the lock, and 1. Secure the front of the panel, and To remove the panel then slide the panel forward to re- then push the rear of the panel in 1.
  • Page 39 PERIODIC MAINTENANCE AND MINOR REPAIR 2. Pull the rear of the panel out, and To install the panel then slide the panel forward to re- 1. Secure the front of the panel, and lease it in the front. then push the rear of the panel in. 2.

  • Page 40: Checking The Spark Plugs

    Instead, have a Since heat and deposits will cause any Yamaha dealer check the motorcycle. spark plug to slowly erode, the spark 3. Check each spark plug for elec- plugs should be removed and checked...
  • Page 41 PERIODIC MAINTENANCE AND MINOR REPAIR Tightening torque: Spark plug: 12.5 Nm (1.25 m·kg) NOTE: If a torque wrench is not available when installing a spark plug, a good estimate of the correct torque is 1/4–1/2 turn past finger tight. However, the spark a.

  • Page 42: Engine Oil And Oil Filter Element

    PERIODIC MAINTENANCE AND MINOR REPAIR EAU01523 To change the engine oil (with or with- Right side Engine oil and oil filter out oil filter element replacement) element 1. Start the engine, warm it up for The engine oil level should be checked several minutes, and then turn it before each ride.
  • Page 43 PERIODIC MAINTENANCE AND MINOR REPAIR 1. Engine oil drain bolt 1. Bolt ( 3) 1. Oil filter element 2. Oil pan 2. O-ring 4. Remove the oil filter element cover 3. Remove the engine oil filler cap 5. Remove and replace the oil filter by removing the bolts.

  • Page 44: Cleaning The Air Filter Element

    PERIODIC MAINTENANCE AND MINOR REPAIR 7. Install the engine oil drain bolt, and EC000072 CAUTION: then tighten it to the specified In order to prevent clutch slip- torque. page (since the engine oil also lubricates the clutch), do not Tightening torque: mix any chemical additives Engine oil drain bolt: with the oil or use oils of a...
  • Page 45 PERIODIC MAINTENANCE AND MINOR REPAIR 1. Air filter case cover 1. Air filter element 2. Screw ( 4) 2. Screw ( 3) 4. Lightly tap the air filter element to 2. Remove the air filter case cover by 3. Remove the air filter element by remove most of the dust and dirt, removing the screws.

  • Page 46: Adjusting The Carburetor

    Therefore, most car- air filter case. buretor adjustments should be left to a The engine should never be op- Yamaha dealer, who has the neces- erated without the air filter ele- sary professional knowledge and expe- ment installed, otherwise the rience.

  • Page 47: Adjusting The Engine Idling Speed

    4,000–5,000 r/min. NOTE: Engine idling speed: The engine is warm when it quickly re- 1,200–1,400 r/min sponds to the throttle. NOTE: If the specified idling speed cannot be obtained as described above, have a Yamaha dealer make the adjustment. 6-15...

  • Page 48: Adjusting The Valve Clearance

    1.75 bar) 2.00 bar) from occurring, the valve clearance regarding the specified tires. 225 kPa 225 kPa must be adjusted by a Yamaha dealer 90 kg–maximum (2.25 kg/cm (2.25 kg/cm 2.25 bar) 2.25 bar) at the intervals specified in the periodic...
  • Page 49 Yamaha dealer fied maximum load for the replace the tire immediately. vehicle.
  • Page 50 PERIODIC MAINTENANCE AND MINOR REPAIR EW000079 Tire information EAU00681 WARNING WARNING This motorcycle is equipped with tube Have a Yamaha dealer replace Have a Yamaha dealer replace tires. excessively worn tires. Besides excessively worn tires. Besides EW000078 WARNING being illegal,...

  • Page 51: Spoke Wheels

    If any dam- 2. Clutch lever free play adjusting bolt 2. Clutch lever free play adjusting nut age is found, have a Yamaha c. Clutch lever free play 3. If the specified clutch lever free dealer replace the wheel. Do not...

  • Page 52: Adjusting The Brake Lever Free Play

    WARNING sure 5–8 mm as shown. Periodically trol and an accident. It is advisable to have a Yamaha check the brake lever free play and, if dealer make these adjustments. necessary, adjust it as follows.
  • Page 53 If proper adjustment cannot be obtained as described, have a Yamaha dealer make this ad- 1. Brake pedal position adjusting bolt 1. Brake pedal free play adjusting nut justment. 2. Locknut...

  • Page 54: Adjusting The Rear Brake Light Switch

    Yamaha dealer replace Turn the adjusting nut while holding the the brake pads as a set. rear brake light switch in place. To make the brake light come on earlier, turn the adjusting nut in direction a.

  • Page 55: Checking The Brake Fluid Level

    Yamaha brake pads for wear and the brake sys- dealer replace the brake shoes as a tem for leakage.

  • Page 56: Changing The Brake Fluid

    Brake fluid may deteriorate paint- EAU03238 EAU00744 Changing the brake fluid Drive chain slack ed surfaces or plastic parts. Al- Have a Yamaha dealer change the The drive chain slack should be ways clean spilled fluid brake fluid at the intervals specified in checked before each ride and adjusted immediately.
  • Page 57 PERIODIC MAINTENANCE AND MINOR REPAIR a. Drive chain slack 1. Axle nut 1. Alignment marks 2. Drive chain puller locknut 2. Drive chain slack adjusting nut 2. Shift the transmission into the neu- 3. Brake pedal free play adjusting nut 3.

  • Page 58: Lubricating The Drive Chain

    PERIODIC MAINTENANCE AND MINOR REPAIR EC000096 EAU03006 2. Wipe the drive chain dry. Lubricating the drive chain CAUTION: 3. Thoroughly lubricate the drive The drive chain must be cleaned and Improper drive chain slack will over- chain with a special O-ring chain lubricated at the intervals specified in load the engine as well as other vital lubricant.

  • Page 59: Checking And Lubricating The Cables

    If a cable is damaged or does not move smoothly, have a Recommended lubricant: Yamaha dealer check or replace it. Lithium-soap-based grease (all-purpose grease) Recommended lubricant: Engine oil...

  • Page 60: Checking And Lubricating The Brake And Clutch Levers

    EW000113 Recommended lubricant: WARNING Lithium-soap-based grease If the sidestand does not move up (all-purpose grease) and down smoothly, have a Yamaha dealer check or repair it. Recommended lubricant: Lithium-soap-based grease (all-purpose grease) 6-28...

  • Page 61: Checking The Steering

    If any free Securely support the motorcycle so position. play can be felt, have a Yamaha that there is no danger of it falling 2. While applying the front brake, dealer...

  • Page 62: Checking The Wheel Bearings

    PERIODIC MAINTENANCE AND MINOR REPAIR EAU01144 To charge the battery Checking the wheel bearings Have a Yamaha dealer charge the bat- The front and rear wheel bearings must tery as soon as possible if it seems to be checked at the intervals specified in have discharged.
  • Page 63 (MF) bat- charge it if necessary. • INTERNAL: Drink large quan- tery charger, have a Yamaha 3. Fully charge the battery before in- tities of water or milk and im- dealer charge your battery.

  • Page 64: Replacing The Fuses

    EAU01749 3. Headlight fuse Replacing the fuses 4. If the fuse immediately blows 4. Ignition fuse again, have a Yamaha dealer The fuse boxes are located behind 5. Signaling system fuse check the electrical system. 6. Carburetor heater fuse panel B. (See page 6-6 for panel re- 7.

  • Page 65: Replacing The Headlight Bulb

    PERIODIC MAINTENANCE AND MINOR REPAIR 1. Screw ( 2) 1. Headlight coupler 1. Headlight bulb cover 2. Disconnect the headlight coupler, EAU03188 Replacing the headlight bulb and then remove the headlight unit This motorcycle is equipped with a and bulb cover. quartz bulb headlight.
  • Page 66 PERIODIC MAINTENANCE AND MINOR REPAIR 6. Install the headlight unit by install- ing the screws. 7. Have a Yamaha dealer adjust the headlight beam if necessary. 1. Headlight bulb holder 1. Do not touch this area. 3. Unhook the headlight bulb holder,...

  • Page 67: Replacing The Tail/Brake Light Bulb

    PERIODIC MAINTENANCE AND MINOR REPAIR 1. Screw ( 2) 1. Tail/brake light bulb 2. Remove the defective bulb by EAU01623 Replacing the tail/brake light pushing it in and turning it counter- bulb clockwise. 1. Remove the tail/brake light lens by 3.

  • Page 68: Replacing A Turn Signal Light Bulb

    PERIODIC MAINTENANCE AND MINOR REPAIR EAU01579 Supporting the motorcycle Since this model is not equipped with a centerstand, follow these precautions when removing the front and rear wheel or performing other mainte- nance requiring the motorcycle to stand upright. Check that the motor- cycle is in a stable and level position 1.

  • Page 69: Front Wheel

    3. Remove the rubber cap, and then EW000122 loosen the wheel axle. WARNING 4. Lift the front wheel off the ground It is advisable to have a Yamaha according to the procedure on dealer service the wheel. page 6-36. Securely support the motor- 5.
  • Page 70 PERIODIC MAINTENANCE AND MINOR REPAIR 6. Tighten the wheel axle to the specified torque, and then install the rubber cap. Tightening torque: Wheel axle: 59 Nm (5.9 m·kg) 7. Install the front wheel axle pinch 1. Retainer bolt, and then tighten it to the specified torque.

  • Page 71: Rear Wheel

    PERIODIC MAINTENANCE AND MINOR REPAIR EAU03189 Rear wheel To remove the rear wheel EW000122 WARNING It is advisable to have a Yamaha dealer service the wheel. Securely support the motor- cycle so that there is no danger 1. Axle nut 1. Wheel axle 2.

  • Page 72: Troubleshooting

    However, should your motorcycle the brake shoe plate by installing After adjusting the brake pedal free require any repair, take it to a Yamaha the bolt and the nut, and then tight- play, check the operation of the dealer, whose skilled technicians have en the bolt to the specified torque.

  • Page 73: Troubleshooting Chart

    Remove the spark plugs and check the electrodes. The engine does not start. Have a Yamaha dealer check the vehicle. Check the battery. 4. Battery The engine turns over The battery is good.

  • Page 74: Motorcycle Care And Storage

    M OTORCYCLE CARE AND STORAGE EAU03430 Care Before cleaning Cleaning 1. Cover the muffler outlets with plas- ECA00010 While the open design of a motorcycle CAUTION: tic bags after the engine has reveals the attractiveness of the tech- Avoid using strong acidic wheel cooled down.
  • Page 75 MOTORCYCLE CARE AND STORAGE Do not use any harsh chemical For motorcycles equipped with After riding in the rain, near the sea or products on plastic parts. Be a windshield: Do not use strong on salt-sprayed roads sure to avoid using cloths or cleaners or hard sponges as Since sea salt or salt sprayed on roads sponges which have been in...
  • Page 76 NOTE: 4. To prevent corrosion, it is recom- Consult a Yamaha dealer for advice on mended to apply a corrosion pro- what products to use. tection spray...

  • Page 77: Storage

    MOTORCYCLE CARE AND STORAGE Storage Long-term a. Remove the spark plug caps and Before storing your motorcycle for spark plugs. several months: b. Pour a teaspoonful of engine oil Short-term 1. Follow all the instructions in the into each spark plug bore. Always store your motorcycle in a cool, “Care”...
  • Page 78 MOTORCYCLE CARE AND STORAGE 6. Lubricate all control cables and NOTE: Make any necessary repairs before the pivoting points of all levers and storing the motorcycle. pedals as well as of the sidestand/ centerstand. 7. Check and, if necessary, correct the tire air pressure, and then lift the motorcycle so that both of its wheels are off the ground.

  • Page 79: Specifications

    EAU01038 S PECIFICATIONS Specifications CS-01E Model XVS250 Engine oil Dimensions Type -20 -10 10 20 30 40 50 ˚C Overall length 2,320 mm SAE 10W-30 Overall width 910 mm Overall height 1,075 mm SAE 10W-40 Seat height 670 mm SAE 15W-40...

  • Page 80: Specifications

    SPECIFICATIONS Air filter Dry type element Gear ratio Fuel 2.643 Type Regular unleaded gasoline 1.684 Fuel tank capacity 11 L 1.261 Fuel reserve amount 3.4 L 1.000 Carburetor 0.821 Manufacturer MIKUNI Chassis Model quantity BDS26 Frame type Double cradle Spark plug Caster angle 35°...
  • Page 81 SPECIFICATIONS Maximum load* 180 kg Rear Tire air pressure (measured Type Drum brake on cold tires) Operation Right foot Up to 90 kg* Suspension Front 175 kPa (1.75 kg/cm , 1.75 bar) Front Telescopic fork Rear 200 kPa (2.00 kg/cm , 2.00 bar) Rear Swingarm...
  • Page 82 SPECIFICATIONS Bulb voltage, wattage quantity Headlight 12 V, 60/55 W Tail/brake light 12 V, 5/21 W Turn signal light 12 V, 21 W Auxiliary light 12 V, 4 W Meter lighting 12 V, 1.7 W Neutral indicator light 12 V, 1.7 W High beam indicator light 12 V, 1.7 W Turn signal indicator light...

  • Page 83: Conversion Table

    SPECIFICATIONS EAU01064 Conversion table CS-02E Conversion table All specification data in this manual are listed in SI and METRIC TO IMPERIAL METRIC UNITS. Metric unit Multiplier Imperial unit Use this table to convert METRIC unit data to IMPERIAL m·kg 7.233 ft·lb m·kg 86.794...

  • Page 84: Consumer Information

    Record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehi- cle is stolen. 1. Key identification number 1.

  • Page 85: Model Label

    1. Model label EAU03757 Model label The model label is affixed to the loca- tion shown. Record the information on this label in the space provided. This in- formation will be needed when ordering spare parts from a Yamaha dealer.
  • Page 88 YAMAHA MOTOR CO., LTD. PRINTED ON RECYCLED PAPER PRINTED IN JAPAN 2000 · 8 - 0.3 1 CR...

Table of Contents