Download  Print this page

Advertisement

Table of Contents
OWNER'S MANUAL
XVS1100
XVS1100A
5KS-28199-E1

Advertisement

Table of Contents

   Summary of Contents for YAMAHA XVS1100

  • Page 1 OWNER’S MANUAL XVS1100 XVS1100A 5KS-28199-E1...
  • Page 3 Please take the time to read this manual thoroughly, so as to enjoy all advantages of your XVS1100/XVS1100A. The owner’s manual does not only instruct you in how to operate, inspect and maintain your motorcycle, but also in how to safeguard yourself and others from trouble and injury.
  • Page 4 This manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle is subsequently sold. Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your motorcycle and this manual.
  • Page 5: Important Manual Information

    IMPORTANT MANUAL INFORMATION EW000002 WARNING PLEASE READ THIS MANUAL CAREFULLY AND COMPLETELY BEFORE OPERATING THIS MOTORCYCLE.
  • Page 6 IMPORTANT MANUAL INFORMATION EAU00008 XVS1100/XVS1100A OWNER’S MANUAL © 2000 by Yamaha Motor Co., Ltd. 1st Edition, April 2000 All rights reserved. Any reprinting or unauthorized use without the written permission of Yamaha Motor Co., Ltd. is expressly prohibited. Printed in Japan.
  • Page 7: Table Of Contents

    EAU00009 TABLE OF CONTENTS 1 GIVE SAFETY THE RIGHT OF WAY 2 DESCRIPTION 3 INSTRUMENT AND CONTROL FUNCTIONS 4 PRE-OPERATION CHECKS 5 OPERATION AND IMPORTANT RIDING POINTS 6 PERIODIC MAINTENANCE AND MINOR REPAIR 7 MOTORCYCLE CARE AND STORAGE 8 SPECIFICATIONS 9 CONSUMER INFORMATION INDEX...
  • Page 9: Give Safety The Right Of Way

    GIVE SAFETY THE RIGHT OF WAY GIVE SAFETY THE RIGHT OF WAY..........1-1...
  • Page 10 G IVE SAFETY THE RIGHT OF WAY EAU00021 Motorcycles are fascinating vehicles, which can give you an unsurpassed feeling of power and freedom. However, they also impose certain limits, which you must accept; even the best motorcycle does not ignore the laws of physics. Regular care and maintenance are essential for preserving value and operating condition of your motorcycle.
  • Page 11: Description

    DESCRIPTION Left view (XVS1100) ................2-1 Right view (XVS1100) ................ 2-2 Left view (XVS1100A) ................ 2-3 Right view (XVS1100A)..............2-4 Controls and instruments (XVS1100/XVS1100A) ......2-5...
  • Page 12: Left View (xvs1100)

    D ESCRIPTION EAU00026 Left view (XVS1100) 1. Shift pedal (page 3-6) 2. Fuel cock (page 3-9) 3. Spring preload adjusting ring (shock absorber assembly) (page 3-15) 4. Helmet holder (page 3-13) 5. Storage compartment (page 3-14) 6. Owner’s tool kit (page 6-1) 7.
  • Page 13: Right View (xvs1100)

    DESCRIPTION Right view (XVS1100) 9. Oil filter element (page 6-7) 10. Battery (page 6-26) 11. Main fuse (page 6-27) 12. Main switch/steering lock (page 3-1) 13. Air filter (page 6-11) 14. Brake pedal (page 3-7)
  • Page 14: Left View (xvs1100a)

    DESCRIPTION Left view (XVS1100A) 1. Shift pedal (page 3-6) 2. Fuel cock (page 3-9) 3. Spring preload adjusting ring (shock absorber assembly) (page 3-15) 4. Helmet holder (page 3-13) 5. Storage compartment (page 3-14) 6. Owner’s tool kit (page 6-1) 7.
  • Page 15: Right View (xvs1100a)

    DESCRIPTION Right view (XVS1100A) 9. Oil filter element (page 6-7) 10. Battery (page 6-26) 11. Main fuse (page 6-27) 12. Main switch/steering lock (page 3-1) 13. Air filter (page 6-11) 14. Brake pedal (page 3-7)
  • Page 16: Controls And Instruments (xvs1100/xvs1100a)

    DESCRIPTION Controls and instruments (XVS1100/XVS1100A) 1. Clutch lever (page 3-5) 2. Left handlebar switches (page 3-4) 3. Starter (choke) lever “ ” (page 3-10) 4. Speedometer unit (page 3-3) 5. Fuel tank cap (page 3-8) 6. Right handlebar switches (page 3-5) 7.
  • Page 17: Instrument And Control Functions

    Indicator lights ................... 3-2 Speedometer unit ................3-3 Anti-theft alarm (optional) ..............3-4 Handlebar switches ................3-4 Clutch lever ..................3-5 Shift pedal (XVS1100)................ 3-6 Shift pedal (XVS1100A) ..............3-6 Brake lever ..................3-6 Brake pedal ..................3-7 Fuel tank cap ..................3-8 Fuel ....................
  • Page 18: Main Switch/steering Lock

    I NSTRUMENT AND CONTROL FUNCTIONS EAU00027 1. Push 2. Turn EAU00029 EAU00040 Main switch/steering lock LOCK EW000016 The steering is locked, and all electrical WARNING The main switch/steering lock controls systems are off. The key can be re- the ignition and lighting systems, and is Never turn the key to “OFF”...
  • Page 19: Indicator Lights

    The steering is locked, and the taillight pushing the start switch, have a and auxiliary light are on, but all other Yamaha dealer check the electri- electrical systems are off. The key can cal circuit. be removed.
  • Page 20: Speedometer Unit

    This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this oc- curs, have the Yamaha dealer check the self-diagnosis system. The electrical circuit of the warning light can be checked according to the fol- lowing procedure.
  • Page 21: Anti-theft Alarm (optional)

    This motorcycle can be equipped with beam and to “ ” for the low beam. an optional anti-theft alarm by a EAU00129 Yamaha dealer. Contact a Yamaha Horn switch “ ” dealer for more information. Press this switch to sound the horn.
  • Page 22: Clutch Lever

    INSTRUMENT AND CONTROL FUNCTIONS EAU00143 Start switch “ ” Push this switch to crank the engine with the starter. EC000005 CAUTION: See page 5-1 for starting instruc- tions prior to starting the engine. 1. Engine stop switch 1. Clutch lever 2.
  • Page 23: Shift Pedal (xvs1100)

    1. Shift pedal 1. Brake lever EAU00157 EAU01215 EAU00158 Shift pedal (XVS1100) Shift pedal (XVS1100A) Brake lever The shift pedal is located on the left The shift pedal is located on the left The brake lever is located at the right...
  • Page 24: Brake Pedal

    INSTRUMENT AND CONTROL FUNCTIONS XVS1100 XVS1100A 1. Brake pedal 1. Brake pedal EAU00162 Brake pedal The brake pedal is on the right side of the motorcycle. To apply the rear brake, press down on the brake pedal.
  • Page 25: Fuel Tank Cap

    INSTRUMENT AND CONTROL FUNCTIONS 2. Turn the key counterclockwise to the original position, remove it, and then close the lock cover. NOTE: The fuel tank cap cannot be installed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly installed and locked.
  • Page 26: Fuel Cock

    INSTRUMENT AND CONTROL FUNCTIONS EAU00185 Off position Normal position CAUTION: Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfac- es or plastic parts. EAU00191 Recommended fuel: 1. Pointed end positioned over “OFF” 1.
  • Page 27: Starter (choke) Lever

    INSTRUMENT AND CONTROL FUNCTIONS ECA00038 Reserve position CAUTION: Do not use the starter (choke) for more than 3 minutes as the exhaust pipe may discolor from excessive heat. In addition, extended use of the starter (choke) will cause after- burning. If this occurs, turn off the starter (choke).
  • Page 28: Seats (xvs1100)

    1. Nut 1. Projection 1. Bolt ( 2) 2. Seat holder 2. Bracket EAU01710 Seats (XVS1100) To install the passenger seat Rider seat Insert the projection on the front of the To remove the rider seat Passenger seat passenger seat into the seat holder as 1.
  • Page 29: Seats (xvs1100a)

    INSTRUMENT AND CONTROL FUNCTIONS XVS1100 XVS1100A XVS1100A 1. Projection ( 2) 1. Bolt 1. Projection 2. Seat holder ( 2) 2. Seat holder EAU03202 Seats (XVS1100A) To install the rider seat To install the passenger seat 1. Insert the projections on the front...
  • Page 30: Helmet Holder

    INSTRUMENT AND CONTROL FUNCTIONS XVS1100A XVS1100A 1. Bolt 1. Projection ( 2) 1. Helmet holder 2. Seat holder ( 2) Rider seat EAU00260 Helmet holder To install the rider seat To remove the rider seat To open the helmet holder, insert the 1.
  • Page 31: Storage Compartment

    INSTRUMENT AND CONTROL FUNCTIONS 1. Storage compartment cover 1. Lock cover 1. Storage compartment cover 2. Lock To open the storage compartment 2. Pull the storage compartment cov- EAU01869 1. Slide the lock cover open, insert er out as shown. Storage compartment the key into the lock, and then turn The storage compartment is located on...
  • Page 32: Adjusting The Shock Absorber Assembly

    1. Remove the rider seat. (See shown. then pulling the fastener out. page 3-11 [XVS1100] or 3-13 2. Turn the key counterclockwise, re- [XVS1100A] for rider seat removal move it, and then close the lock and installation procedures.)
  • Page 33 INSTRUMENT AND CONTROL FUNCTIONS XVS1100 XVS1100A 1. Ignitor unit panel 1. Quick fastener ( 3) 1. Quick fastener ( 2) 2. Mudguard 2. Mudguard 3. Pull the ignitor unit panel out to the 4. Remove the mudguard by remov- right.
  • Page 34 Always have a Yamaha dealer Use the special wrench included in service the shock absorber. 7. Install the rider seat.
  • Page 35: Luggage Strap Holders

    There is a luggage strap holder on responsibility of raising the side- each passenger footrest. stand before starting off. Therefore, check this system regularly as de- scribed below and have a Yamaha dealer repair it if it does not function properly. 3-18...
  • Page 36: Ignition Circuit Cut-off System

    WARNING lowing functions. If a malfunction is noted, have a It prevents starting when the trans- Yamaha dealer check the system mission is in gear and the side- before riding. stand is up, but the clutch lever is not pulled.
  • Page 37 5. Push the start switch. Does the engine start? The neutral switch may be defective. The motorcycle should not be ridden until checked by a Yamaha dealer. With the engine still running: 6. Move the sidestand up. 7. Keep the clutch lever pulled.
  • Page 39: Pre-operation Checks

    PRE-OPERATION CHECKS Pre-operation check list..............4-1...
  • Page 40: Pre-operation Check List

    P RE-OPERATION CHECKS EAU01114 The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly, even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss of tire air pressure could have serious consequences.
  • Page 41 PRE-OPERATION CHECKS ITEM CHECKS PAGE • Make sure that all nuts, bolts and screws are properly tightened. Chassis fasteners — • Tighten if necessary. • Check fuel level. – Fuel • Add fuel if necessary. Lights, signals and switches • Check proper operation. —...
  • Page 43: Operation And Important Riding Points

    OPERATION AND IMPORTANT RIDING POINTS Starting a cold engine ............... 5-1 Starting a warm engine ..............5-3 Shifting ....................5-3 Recommended shift points (for Switzerland only) ......5-4 Tips for reducing fuel consumption ........... 5-4 Engine break-in ................. 5-5 Parking ....................5-5...
  • Page 44: Starting A Cold Engine

    If the should be on, otherwise have a sidestand is not raised com- Yamaha dealer check the electrical cir- pletely, it could contact the cuit. ground and distract the opera- tor, resulting in a possible loss of control.
  • Page 45: Operation And Important Riding Points

    5. Start the engine by pushing the if it does not go off after starting the start switch. engine with sufficient engine oil, have a Yamaha dealer check the NOTE: electrical circuit. If the engine fails to start, release the start switch, wait a few seconds, and then try again.
  • Page 46: Starting A Warm Engine

    OPERATION AND IMPORTANT RIDING POINTS EAU01258 XVS1100 XVS1100A Starting a warm engine Follow the same procedure as for start- ing a cold engine with the exception that the starter (choke) is not required when the engine is warm. EAU00423 Shifting...
  • Page 47: Recommended Shift Points (for Switzerland Only)

    OPERATION AND IMPORTANT RIDING POINTS EC000048 EAU02941 EAU00424 Recommended shift points Tips for reducing fuel CAUTION: (for Switzerland only) consumption Even with the transmission in The recommended shift points during Fuel consumption depends largely on the neutral position, do not acceleration are shown in the table be- your riding style.
  • Page 48: Engine Break-in

    1,600 km and beyond The vehicle can now be operated nor- mally. EC000049 CAUTION: If any engine trouble should occur during the engine break-in period, immediately have a Yamaha dealer check the vehicle.
  • Page 49: Periodic Maintenance And Minor Repair

    PERIODIC MAINTENANCE AND MINOR REPAIR Owner’s tool kit ............6-1 Changing the brake fluid ........6-22 Periodic maintenance and lubrication chart ..6-2 Checking and lubricating the cables ....6-22 Removing and installing the panel .......6-5 Checking and lubricating the throttle grip and cable ............
  • Page 50: Owner's Tool Kit

    Periodic inspection, adjustment and lu- ence required for a particular job, have brication will keep your vehicle in the a Yamaha dealer perform it for you. safest and most efficient condition pos- EW000063 sible. The most important points of in-...
  • Page 51: Periodic Maintenance And Minor Repair

    PERIODIC MAINTENANCE AND MINOR REPAIR EAU00473 Periodic maintenance and lubrication chart CP-02E Every Every Initial Annual ITEM CHECKS AND MAINTENANCE JOBS 1,000 km check 6,000 km 12,000 km • Check fuel hoses for cracks or damage. Fuel line • Replace if necessary. •...
  • Page 52 PERIODIC MAINTENANCE AND MINOR REPAIR Every Every Initial Annual ITEM CHECKS AND MAINTENANCE JOBS 1,000 km check 6,000 km 12,000 km • Check bearing for looseness or damage. Wheel bearings • Replace if necessary. • Check swingarm pivoting point for play. •...
  • Page 53 • Correct if necessary. switches • Adjust headlight beam if necessary. * Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service. EAU03206 NOTE: The annual checks must be performed every year except if a 6,000 km or 12,000 km maintenance is performed instead.
  • Page 54: Removing And Installing The Panel

    PERIODIC MAINTENANCE AND MINOR REPAIR 1. Panel A 1. Bolt To install the panel EAU01777 EAU00491 Removing and installing the Panel A Place the panel in the original position, To remove the panel panel and then install the bolt. Remove the bolt, and then pull the pan- The panel shown above needs to be el off as shown.
  • Page 55: Checking The Spark Plugs

    Do not attempt to diagnose such problems yourself. Instead, have a Yamaha dealer check the motorcycle. 3. Check each spark plug for elec- trode erosion and excessive car- bon or other deposits, and replace 1.
  • Page 56: Engine Oil And Oil Filter Element

    PERIODIC MAINTENANCE AND MINOR REPAIR Tightening torque: Spark plug: 20 Nm (2.0 m·kg) NOTE: If a torque wrench is not available when installing a spark plug, a good estimate of the correct torque is 1/4–1/2 turn past finger tight. However, the spark a.
  • Page 57 PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: Make sure that the motorcycle is posi- tioned straight up when checking the oil level. A slight tilt to the side can result in a false reading. 2. Start the engine, warm it up for sev- eral minutes, and then turn it off.
  • Page 58: Final Gear Oil

    Oil quantity: for oil leakage before each ride. If any immediately turn the engine off Without oil filter element replace- leakage is found, have a Yamaha deal- and check for the cause. ment: er check and repair the motorcycle. In 3.0 L...
  • Page 59 PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: Recommended final gear oil: The oil level should be at the brim of Hypoid gear oil SAE 80 (API GL4) the filler hole. or multigrade hypoid gear oil SAE 3. If the oil is below the brim of the fill- 80W-90 er hole, add sufficient oil of the rec- Oil quantity:...
  • Page 60: Cleaning The Air Filter Element

    PERIODIC MAINTENANCE AND MINOR REPAIR 1. Air filter case cover 1. Air filter element 2. Screw ( 3) 2. Projection 3. Lightly tap the air filter element to 3. Tab EAU03195 remove most of the dust and dirt, Cleaning the air filter element 4.
  • Page 61: Adjusting The Carburetors

    Therefore, most car- checked and, if necessary, adjusted as buretor adjustments should be left to a follows at the intervals specified in the Yamaha dealer, who has the neces- periodic maintenance and lubrication sary professional knowledge and expe- chart.
  • Page 62: Adjusting The Throttle Cable Free Play

    To prevent this your motorcycle, note the following from occurring, the valve clearance points regarding the specified tires. must be adjusted by a Yamaha dealer at the intervals specified in the periodic Tire air pressure maintenance and lubrication chart.
  • Page 63 PERIODIC MAINTENANCE AND MINOR REPAIR XVS1100 EWA00012 Adjust the suspension and tire WARNING air pressure with regard to the CE-01E Tire air pressure (measured on cold tires) Because loading has an enormous load. Load* Front Rear impact on the handling, braking,...
  • Page 64 Manufacturer Size Type or glass fragments in it, or if the side- Dunlop 110/90-18 61S K555F wall is cracked, have a Yamaha dealer Bridgestone 110/90-18 61S EXEDRA L309 replace the tire immediately. REAR (XVS1100) CE-08E Minimum tire tread depth...
  • Page 65: Spoke Wheels

    The replacement of all wheel- age before each ride. If any dam- and brake-related parts, includ- age is found, have a Yamaha ing the tires, should be left to a dealer replace the wheel. Do not Yamaha dealer, who has the...
  • Page 66: Adjusting The Clutch Lever Free Play

    NOTE: If the specified free play cannot be ob- tained as described above or if the clutch does not operate correctly, have a Yamaha dealer check the internal clutch mechanism. 1. Locknut a. Brake lever free play 2. Adjusting bolt EAU00696 c.
  • Page 67 1. Locknut system. If there is air in the hy- 2. Brake lever free play adjusting bolt draulic system, have a Yamaha 1. Loosen the locknut at the brake le- dealer bleed the system before ver.
  • Page 68: Adjusting The Brake Pedal Position

    If there tivated by the brake pedal, is properly (XVS1100) or 98.5 mm (XVS1100A) is air in the hydraulic system, have a adjusted when the brake light comes above the top of the footrest as shown.
  • Page 69: Checking The Front And Rear Brake Pads

    To check the brake pad wear, check wear indicator grooves. If a brake pad has worn to the point that the wear indicator groove has almost disappeared, have a Yamaha dealer replace the brake pads as a set. 6-20...
  • Page 70: Checking The Brake Fluid Level

    Use only the recommended quali- brake fluid level goes down sud- is above the minimum level mark and ty brake fluid, otherwise the rubber denly, have a Yamaha dealer replenish if necessary. A low brake flu- seals may deteriorate, causing check the cause.
  • Page 71: Changing The Brake Fluid

    EAU02962 EAU03197 Changing the brake fluid Checking and lubricating the Checking and lubricating the Have a Yamaha dealer change the cables throttle grip and cable brake fluid at the intervals specified in The operation of all control cables and The operation of the throttle grip and...
  • Page 72: Checking And Lubricating The Brake And Shift Pedals

    PERIODIC MAINTENANCE AND MINOR REPAIR 4. Grease the metal-to-metal contact surface of the throttle grip, and then install the grip by installing the screws. Recommended lubricant: Throttle cable: Engine oil Throttle grip housing and grip: Lithium-soap-based grease EAU03199 EAU03164 (all-purpose grease) Checking and lubricating the Checking and lubricating the brake and shift pedals...
  • Page 73: Checking And Lubricating The Sidestand

    CAUTION: and down smoothly, have a Yamaha If any damage is found or the front dealer check or repair it. fork does not operate smoothly, have a Yamaha dealer check or re- Recommended lubricant: pair it. Lithium-soap-based grease (all-purpose grease)
  • Page 74: Checking The Steering

    The front and rear wheel bearings must ward and backward. If any free be checked at the intervals specified in play can be felt, have a Yamaha the periodic maintenance and lubrica- dealer check or repair the steer- tion chart. If there is play in the wheel ing.
  • Page 75: Battery

    PERIODIC MAINTENANCE AND MINOR REPAIR EAU00800 EW000116 KEEP THIS AND ALL BATTER- Battery WARNING IES OUT OF THE REACH OF This motorcycle is equipped with a Electrolyte is poisonous and CHILDREN. sealed-type (MF) battery, which does dangerous since it contains sul- not require any maintenance.
  • Page 76: Replacing The Fuses

    Always keep battery The main fuse box is located under the Have a Yamaha dealer charge the bat- charged. Storing a discharged rider seat. To access the main fuse tery as soon as possible if it seems to battery can cause permanent box, proceed as follows.
  • Page 77 PERIODIC MAINTENANCE AND MINOR REPAIR If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage.
  • Page 78: Replacing The Headlight Bulb

    4. If the fuse immediately blows 3. Remove the headlight bulb holder EAU03003 Replacing the headlight bulb again, have a Yamaha dealer by turning it counterclockwise, and This motorcycle is equipped with a check the electrical system. then remove the defective bulb.
  • Page 79: Replacing A Turn Signal Light Bulb Or The Tail/brake Light Bulb

    1. Remove the lens by removing the ing the screws. touch the bulb until it has cooled screws. 7. Have a Yamaha dealer adjust the down. 2. Remove the defective bulb by headlight beam if necessary. pushing it in and turning it counter- 4.
  • Page 80: Troubleshooting

    However, should your motorcycle Do not overtighten the screws, oth- wise until it stops. require any repair, take it to a Yamaha 4. Install the lens by installing the erwise the lens may break. dealer, whose skilled technicians have screws.
  • Page 81: Troubleshooting Chart

    Remove the spark plugs and check the electrodes. The engine does not start. Have a Yamaha dealer check the vehicle. Check the battery. 4. Battery The engine turns over The battery is good.
  • Page 83: Motorcycle Care And Storage

    MOTORCYCLE CARE AND STORAGE Care ....................7-1 Storage....................7-4...
  • Page 84 M OTORCYCLE CARE AND STORAGE EAU03200 Care Before cleaning Cleaning 1. Cover the muffler outlets with plas- ECA00010 While the open design of a motorcycle CAUTION: tic bags after the engine has reveals the attractiveness of the tech- Avoid using strong acidic wheel cooled down.
  • Page 85: Motorcycle Care And Storage

    MOTORCYCLE CARE AND STORAGE thinner, fuel (gasoline), rust re- shield is scratched, use a quali- After normal use movers or inhibitors, brake flu- ty plastic polishing compound Remove dirt with warm water, a mild id, antifreeze or electrolyte. after washing. detergent, and a soft, clean sponge, Do not use high-pressure wash- and then rinse thoroughly with clean...
  • Page 86 MOTORCYCLE CARE AND STORAGE 1. Clean the motorcycle with cold After cleaning EWA00031 WARNING water and a mild detergent, after 1. Dry the motorcycle with a chamois Make sure that there is no oil or the engine has cooled down. or an absorbing cloth.
  • Page 87 MOTORCYCLE CARE AND STORAGE Storage Long-term NOTE: Consult a Yamaha dealer for advice on Before storing your motorcycle for sev- what products to use. eral months: Short-term 1. Follow all the instructions in the Always store your motorcycle in a cool, “Care”...
  • Page 88 MOTORCYCLE CARE AND STORAGE c. Install the spark plug caps onto the 7. Check and, if necessary, correct spark plugs, and then place the the tire air pressure, and then lift spark plugs on the cylinder head the motorcycle so that both of its so that the electrodes are ground- wheels are off the ground.
  • Page 89: Specifications

    SPECIFICATIONS Specifications ..................8-1 Conversion table ................8-6...
  • Page 90: Specifications

    S PECIFICATIONS EAU01038 Specifications CS-01E Model XVS1100/XVS1100A Engine Dimensions Engine type Air-cooled 4-stroke, SOHC XVS1100 Cylinder arrangement V type 2-cylinder Overall length 2,405 mm Displacement 1,063 cm Overall width 895 mm Bore stroke 95.0 75.0 mm Overall height 1,095 mm Compression ratio 8.3:1...
  • Page 91 Dry type element 1.032 Fuel 0.853 Type Regular unleaded gasoline Chassis Fuel tank capacity 17 L Frame type Double cradle Fuel reserve amount 4.5 L Caster angle 33° Carburetor Trail Manufacturer MIKUNI XVS1100 136 mm Model quantity BSR37 XVS1100A 132 mm...
  • Page 92 SPECIFICATIONS Tires XVS1100A XVS1100 Front Front Type Tube Type Tube Size 130/90-16 67S Size 110/90-18 61S Manufacturer/ model Dunlop / D404F Manufacturer/ model Bridgestone / EXEDRA L309 Rear Dunlop / K555F Type Tube Rear Size 170/80-15 M/C 77S Type Tube...
  • Page 93 SPECIFICATIONS Wheels Suspension XVS1100 Front Telescopic fork Front Rear Swingarm (link suspension) Type Spoke Spring/shock absorber Size 2.15 Front Coil spring / oil damper Rear Rear Coil spring / gas-oil damper, spring preload adjustable Type Spoke Wheel travel Size 15M/C MT4.50...
  • Page 94 SPECIFICATIONS Bulb voltage, wattage quantity Headlight 12 V, 60/55 W Auxiliary light 12 V, 4 W Tail/brake light 12 V, 5/21 W Turn signal light 12 V, 21 W Meter light 14 V, 1.4 W Oil level warning light 12 V, 1.7 W Neutral indicator light 12 V, 1.7 W Turn signal indicator light...
  • Page 95: Conversion Table

    SPECIFICATIONS EAU01064 Conversion table CS-02E Conversion table All specification data in this manual are listed in SI and METRIC TO IMPERIAL METRIC UNITS. Metric unit Multiplier Imperial unit Use this table to convert METRIC unit data to IMPERIAL m·kg 7.233 ft·lb m·kg 86.794...
  • Page 97: Consumer Information

    CONSUMER INFORMATION Identification numbers ............... 9-1 Key identification number ..............9-1 Vehicle identification number ............. 9-1 Model label ..................9-2...
  • Page 98: Identification Numbers

    Record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehi- cle is stolen. 1. Key identification number 1.
  • Page 99: Consumer Information

    Model label The model label is affixed to the frame under the rider seat. (See page 3-11 [XVS1100] or 3-13 [XVS1100A] for rid- er seat removal and installation proce- dures.) Record the information on this label in the space provided. This infor- mation will be needed when ordering spare parts from a Yamaha dealer.
  • Page 100 I NDEX 1 0 - Air filter element, cleaning ......6-11 Final gear oil..........6-9 Left view (XVS1100) ........2-1 Anti-theft alarm (optional)......3-4 Front fork, checking ....... 6-24 Left view (XVS1100A) ......2-3 Fuel ............3-8 Luggage strap holders ......3-18 Fuel cock..........3-9 Battery ...........6-26...
  • Page 101: Throttle Grip

    INDEX Specifications .......... 8-1 Speedometer unit ........3-3 Starter (choke) lever ......3-10 Starting a cold engine ......5-1 Steering, checking ......... 6-25 Storage............ 7-4 Storage compartment ......3-14 Throttle cable free play, adjusting ..6-13 Throttle grip and cable, checking and lubricating........
  • Page 104 YAMAHA MOTOR CO., LTD. PRINTED ON RECYCLED PAPER PRINTED IN JAPAN 2000 · 4 - 0.3 1 CR...

This manual is also suitable for:

Drag star xvs1100aDrag star xvs1100

Comments to this Manuals

Symbols: 0
Latest comments: